Onkyo TX-RZ810 Basic Manual page 45

> Specifications > Settings
Setting Item Default Value
Surr Back Right 0.0 dB
Surr Back Left 0.0 dB
Surround Left 0.0 dB
Subwoofer 0.0 dB
■ 5� Dolby Enabled Speaker
Setting Item Default Value
Dolby Enabled 6.0 ft/1.80 m
Speaker to
Ceiling
AccuReflex Off
12
> Listening Modes > Playback Function
Setting Details
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
Select a value between "－12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "－15.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Setting Details
Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between "0.1
ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units).
• The unit of distance (ft/m) shown is the unit
selected for use in "Distance".
You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": Do not use this function
"On": Use this function
■ 6� Equalizer Settings
You can adjust the output volume of the range of each connected speaker. You can adjust
the volume of the different sound ranges for each of the speakers. You can set three
different equalizers in Preset 1 to 3. You can select up to five bands for the Subwoofer and
nine bands for all other speakers.
Setting Item Default Value
Front 0.0 dB
Center 0.0 dB
Height 0.0 dB
Surround 0.0 dB
Surround Back 0.0 dB
Subwoofer 0.0 dB
> Basic Manual
Troubleshooting | Appendix
Setting Details
After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"－6.0 dB" and "＋6.0 dB" with / .
After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"－6.0 dB" and "＋6.0 dB" with / .
After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"－6.0 dB" and "＋6.0 dB" with / .
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"－6.0 dB" and "＋6.0 dB" with / .
After selecting the speaker frequency from
between 25 Hz" and "16 kHz" with the cursors
/ , adjust the volume of that frequency between
"－6.0 dB" and "＋6.0 dB" with / .
• The setting cannot be changed if anything
other than "No" is set in "Configuration" - "Zone
Speaker" and Zone 2 is on.
After selecting the speaker frequency from
between 25 Hz" and "160 Hz" with the cursors
/ , adjust the volume of that frequency between
"－6.0 dB" and "＋6.0 dB" with / .
• This cannot be selected if "No" is set in
"Configuration" - "Subwoofer".