Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Installation Manual
Advertisement
Table of Contents
Related Manuals for Subzero ws-30
Summary of Contents for Subzero ws-30
- Page 1 Wine Storage Installation WINE STORAGE INSTALLATION INSTRUCTIONS INSTRUCCIONES DE INSTALACIÓN INSTRUCTIONS D’INSTALLATION ISTRUZIONI PER L’INSTALLAZIONE INSTALLATIONSANWEISUNGEN...
- Page 2 ® SUB-ZERO is a registered trademark of Sub-Zero, Inc.
-
Page 3: Model Icbws-30 Installation
Model ICBWS-30 Installation Model ICBWS-30 Installation Site Preparation Make sure that the actual equipment that was shipped to Make sure that the finished rough opening where the wine TOOLS AND MATERIALS REQUIRED: you matches the design you are expecting to install. storage unit is being installed is properly prepared. - Page 4 Model ICBWS-30 Installation subzero.com Standard Installation Opening Dimensions Flush Inset Installation Opening Dimensions Overlay and Classic Stainless Steel Models TOP VIEW TOP VIEW 610 mm 610 mm TOP VIEW OPENING FLUSH DEPTH OPENING DEPTH INSET TO CLEAT OUTLINE OF FLUSH...
- Page 5 Model ICBWS-30 Installation Dual Standard Installation Opening Dimensions Dual Flush Inset Installation Opening Dimensions Overlay and Classic Stainless Steel Models TOP VIEW TOP VIEW 610 mm 610 mm OPENING DEPTH 610 mm TOP VIEW FLUSH TO CLEAT DEPTH OPENING INSET FLUSH DEPTH OUTLINE...
-
Page 6: Electrical Requirements
Model ICBWS-30 Installation subzero.com Electrical Requirements Unpack the Unit Grille Removal For model ICBWS-30, the electrical supply should be Uncrate the unit and inspect for any damages. Remove In order to prevent damage to the grille and to access the located within the shaded area shown in the illustration. -
Page 7: Anti-Tip Bracket Installation
Model ICBWS-30 Installation Anti-Tip Bracket Installation IMPORTANT NOTE: For either wood or concrete floor CONCRETE FLOOR APPLICATIONS INSTALL CONCRETE WEDGE ANCHORS: applications, if the #12 x 64 mm screws do not hit a wall After properly locating the anti-tip brackets in the rough 1) Drill a 10 mm diameter hole any depth exceeding the To prevent the unit from tipping forward and provide stud or the wall plate in any of the back holes of the... - Page 8 Model ICBWS-30 Installation subzero.com Position the Unit Level the Unit Door Adjustment Use an appliance dolly to move the unit near the rough Once the unit is in position, extend the front leveling legs The door of the model ICBWS-30 can be adjusted in three opening.
-
Page 9: Panel Installation
Model ICBWS-30 Installation Anchoring Home Alarm Connections Complete the Installation – Model ICBWS-30/S Panel Installation After door and side panels have been installed, the unit If a home alarm system is to be installed on the wine For overlay and flush inset applications, refer to the fol- Before you install the front panel, refer to panel specifica- has been leveled and door adjustment completed, anchor storage unit, the connections should be made using the... -
Page 10: Overlay Panels
Slide the panel into position in the grille frame. be found in the Sub -Zero wine storage design guide and If you are using a grille panel 6 mm or thinner, you will BACKER PANEL on our website, subzero.com. BACKER need to install a filler. PANEL... -
Page 11: Flush Inset Panels
Sub -Zero design guide and on our need to install a filler. BACKER PANEL BACKER website, subzero.com. Reattach the top frame by reinstalling the two top corner PANEL TRIM IMPORTANT NOTE: The size of the flush inset panel is screws. -
Page 12: Dual Installations
Model ICBWS-30 Installation subzero.com Flush Inset Panel Dual Installations Flush Inset Panels—Dual Installation Illustrations A–D provide panel offsets and reveals for When two models ICBWS-30 or a model ICBWS-30 and DUAL FLUSH INSET INSTALLATIONS model ICBWS-30 in a flush inset application. Refer to the... -
Page 13: Side Panels
Model ICBWS-30 Installation Flush Inset Panels—Dual Installation Side Panels When installing two models ICBWS-30 or a model IMPORTANT NOTE: Side panels will need to be installed CUSTOM SIDE PANEL INSTALLATION TOP VIEW TOP VIEW ICBWS-30 and built-in unit side by side in a flush inset before the unit is placed in its final position.
Need help?
Do you have a question about the ws-30 and is the answer not in the manual?
Questions and answers