Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Subzero Manuals
  4. Wine Cooler
  5. 424
  6. Installation manual

Subzero 424 Installation Manual

Hide thumbs

Advertisement

Quick Links

INSTALLATION GUIDE

Wine Storage

Advertisement

loading
Need help?

Need help?

Do you have a question about the 424 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Subzero 424

Summary of Contents for Subzero 424

  • Page 1: Wine Storage

    INSTALLATION GUIDE Wine Storage...

  • Page 2: Table Of Contents

    To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of Models 424 and 424FS Installation ....4 highlighted information throughout this guide: Models 427 and 427R Installation .

  • Page 3: Wine Storage Equipment

    Important product information, including the model and serial number of your unit are listed on the product rating plate. For models 424 and 424FS, the rating plate is located on the underside of the top wall. For models 427, 427R and WS-30, it is attached to the underside of the control panel.

  • Page 4: Models 424 And 424Fs Installation

    It can also be slid 24" into surrounding cabinetry with clearance dimensions (610) ROUGH slightly different than the standard built-in model 424. OPENING DEPTH Make sure that the finished rough opening where the wine storage unit is to be installed is properly prepared. Refer...
  • Page 5 " (6) female spade connectors are located in the compressor compartment and are accessible behind the kickplate on models 424 and 424FS. A minimum of 36" (914) of lead wire should be provided for each contact, exiting the back wall near the electrical outlet.
  • Page 6 Refer to the illustration below. A smaller metal ‘countertop’ bracket is also provided with the model 424, for installations that need to be modified to provide a secure surface for attaching the bracket. This ANTI-TIP BRACKET bracket will secure the front of the unit to the underside of the countertop, above the unit.
  • Page 7 Models 424 and 424FS Installation subzero.com Anti-Tip Bracket Installation WOOD FLOOR APPLICATIONS INSTALLATION FOR CONCRETE WEDGE ANCHORS Use the four #12 x 2 " wood screws and the four " 1) Drill a " (10) diameter hole any depth exceeding the flat washers provided.
  • Page 8 Refer to home alarm connections on page 9, for the location of these lead wires. After the unit is in position, For model 424, the lock is attached to the bottom of the the alarm wiring can be completed from the front.
  • Page 9 If a home alarm system is to be installed on the wine For model 424, the countertop bracket should be used storage unit, the connections should be made using the to make a solid installation. Refer to the illustration on logic supplied with the alarm specifications.
  • Page 10 The overlay model 424/O is available as a glass door (G) Turn power back on to the electrical outlet. or solid door (S) model and is designed to accept a decorative door panel to match surrounding cabinetry.
  • Page 11 IMPORTANT NOTE: After the first three or four mounting Decorative panels are attached to the model 424 door screws are in place, but not completely tightened, close using #8 x " square drive screws passing through the the door and check your panel fit.
  • Page 12 Models 424 and 424FS Installation Overlay Door Panel—Model 424 IMPORTANT NOTE: Install screws in all the mounting holes in the door frame. The nature of the door panel with a The wine storage unit door is made with a sealed narrow outer rim and no connecting center member double wall tempered glass core.
  • Page 13 IMPORTANT NOTE: When you have completed the instal- installed and leveled before door hinge adjustments can lation of the model 424 or 424FS wine storage unit, refer be made. to page 50 for an installation checklist and page 51 for service information.

  • Page 14: Models 427 And 427R Installation

    Models 427 and 427R Installation Models 427 and 427R Installation Make sure that the finished rough opening where the wine storage unit is to be installed is properly prepared. Refer 25" to the installation specifications illustration for rough (635) ROUGH opening dimensions, door swing clearance and electrical OPENING DEPTH...
  • Page 15 Models 427 and 427R Installation subzero.com Electrical Requirements Unpacking and Moving A 115 V AC, 60 Hz, 15 amp circuit breaker and electrical Uncrate the unit, remove its wood base and discard the supply are required. A separate circuit, servicing only this shipping bolts that hold the wood base to the bottom of appliance, is required.
  • Page 16 Models 427 and 427R Installation Anti-Tip Bracket Installation An anti-tip bracket and hardware is provided with the wine WOOD FLOOR APPLICATIONS storage unit. The anti-tip bracket must be installed on a Use the six #12 x 2 " wood screws and the six "...
  • Page 17 Sub-Zero dealer, or call Sub-Zero at 800-222-7820. You can also Always wear safety glasses and use other necessary visit our website at subzero.com. protective devices or apparel when installing or working with anchors. Anchors are not recommended for use in lightweight...
  • Page 18 800-222-7820. You can also visit our website at Pre-level the wine storage unit before rolling into position. subzero.com. This is to allow the unit to engage the anti-tip bracket IMPORTANT NOTE: For accessory stainless steel panels properly.
  • Page 19 Models 427 and 427R Installation subzero.com Leveling Install Molding Level the unit by turning the front leveling legs clockwise The decorative white molding strips for the top and sides to raise the unit, or counterclockwise to lower it. To assist...
  • Page 20 Models 427 and 427R Installation Wiring Connections Before the kickplate/grille is installed, all necessary wiring IMPORTANT NOTE: If you are not responsible for alarm connections in the compressor compartment should be system connection, this information should be supplied to completed. the home security system contractor.
  • Page 21 Models 427 and 427R Installation subzero.com Kickplate/Grille Door Panels Once the unit is leveled and wiring connections made, the Models 427 and 427R are available as a glass door (G) or kickplate/grille can be installed. solid door (S) model. Each of these wine storage units are...
  • Page 22 Models 427 and 427R Installation Stainless Steel Door Panel Overlay Door Panel Before installing the stainless steel door panel, check the Inspect the door panel for the minimum " (16) thickness, panel carefully. Options are available for kickplate/grille the greater width requirements for the stiles (to cover the height, overall height, door swing and door lock.
  • Page 23 Models 427 and 427R Installation subzero.com Overlay Door Panel The screw holes inside the door are hidden under a cover IMPORTANT NOTE: Install screws in all the mounting holes flap on the door gasket. It is necessary to lift the flap to in the door frame.
  • Page 24 Models 427 and 427R Installation Model 427R Drawer Panels TOP OF TEMPLATE IMPORTANT NOTE: Drawer panels for model 427R must FLUSH WITH TOP OF DRAWER PANEL be a minimum of " (16) thick and cannot exceed 12 lbs (5 kg) for each panel. GAP ON SIDE Remove the mounting hardware provided and set aside.
  • Page 25 427, 427R or integrated units together. The kit is available through your Sub-Zero dealer, or call Sub-Zero at 800-222-7820. You can also visit our website at subzero.com. 90° Door Stop Models 427 and 427R have a 90° door stop built into the hinge system.

  • Page 26: Model Ws-30 Installation

    Model WS-30 Installation Model WS-30 Installation Make sure that the actual equipment that was shipped to you matches the design you are expecting to install. Before you begin the installation process, check the exact model number you need against the model number on the shipping carton.
  • Page 27 Model WS-30 Installation subzero.com Site Preparation Make sure that the finished rough opening where the wine TOOLS AND MATERIALS REQUIRED: storage unit is being installed is properly prepared. Refer • Phillips screwdriver set to installation specifications on the following pages. These •...
  • Page 28 Model WS-30 Installation Standard Installation Opening Dimensions Framed, Overlay and Classic Stainless Steel Models TOP VIEW 24" (610) OPENING DEPTH OUTLINE OF UNIT WITH " (19) PANEL 24" (610) OPENING DEPTH " " (746) (2127) OPENING WIDTH OPENING HEIGHT 83" (2108) SIDE VIEW FRONT VIEW...
  • Page 29 Model WS-30 Installation subzero.com Flush Inset Installation Opening Dimensions TOP VIEW 24" " (610) " 24" (610) TOP VIEW (665) DEPTH (665) OPENING TO CLEAT FLUSH OUTLINE OF FLUSH DEPTH INSET CLEAT " UNIT WITH INSET TO CLEAT DEPTH "...
  • Page 30 Model WS-30 Installation Dual Standard Installation Opening Dimensions Framed, Overlay and Classic Stainless Steel Models TOP VIEW 24" (610) OPENING DEPTH OUTLINE OF TWO UNITS WITH " (19) PANEL 24" (610) OPENING DEPTH " (2127) OPENING WIDTH OPENING HEIGHT 83" (2108) SIDE VIEW FRONT VIEW...
  • Page 31 Model WS-30 Installation subzero.com Dual Flush Inset Installation Opening Dimensions TOP VIEW " 24" (610) DEPTH " 24" (665) (610) TOP VIEW FLUSH TO CLEAT (665) OPENING INSET FLUSH DEPTH " OUTLINE OF CLEAT DEPTH INSET TO CLEAT (32) TWO UNITS WITH...

  • Page 32: Electrical Requirements

    Model WS-30 Installation Electrical Requirements For model WS-30, the electrical supply should be located 7" within the shaded area shown in the illustration. Follow the (178) National Electrical Code and local codes and ordinances 6" (152) when installing the receptacle. A separate circuit, servicing only this appliance is required.
  • Page 33 Model WS-30 Installation subzero.com Unpack the Unit Grille Removal Uncrate the unit and inspect for any damages. Remove In order to prevent damage to the grille and to access the the wood base and discard the shipping bolts and power cord, the top grille assembly should be removed brackets that hold the wood base to the bottom of the prior to moving the unit.
  • Page 34 Model WS-30 Installation Anti-Tip Bracket Installation IMPORTANT NOTE: For either wood or concrete floor applications, if the #12 x 2 " screws do not hit a wall To prevent the unit from tipping forward and provide stud or the wall plate in any of the back holes of the a stable installation, the unit must be secured in place brackets, use the provided #8–18 x 1 "...
  • Page 35 Model WS-30 Installation subzero.com Anti-Tip Bracket Installation CONCRETE FLOOR APPLICATIONS INSTALL CONCRETE WEDGE ANCHORS: After properly locating the anti-tip brackets in the rough 1) Drill a " (10) diameter hole any depth exceeding the opening, drill pilot holes " (5) diameter maximum in the minimum embedment.
  • Page 36 Model WS-30 Installation Position the Unit Level the Unit Use an appliance dolly to move the unit near the rough Once the unit is in position, extend the front leveling legs opening. Model WS-30 is equipped with rollers, so it can down by turning the legs clockwise to adjust the height.
  • Page 37 Model WS-30 Installation subzero.com Door Adjustment The door of the model WS-30 can be adjusted in three ways: In and out, side to side tilt, and up and down. Regardless of the adjustment being made, start by slightly loosening the two upper hinge bolts on the upper hinge plate using a "...
  • Page 38 Model WS-30 Installation Anchoring Home Alarm Connections After door and side panels have been installed, the unit If a home alarm system is to be installed on the wine has been leveled and door adjustment completed, anchor storage unit, the connections should be made using the the wine storage unit to the opening.
  • Page 39 IMPORTANT NOTE: For overlay models, there are two information, visit the showroom locator section of our design applications—overlay and flush inset. Be sure to website, subzero.com. use the correct panel size for your application. The 90° door stop will be installed in the top hinge of the door.
  • Page 40 Insert a screwdriver tip into the top corner found in the Sub-Zero design guide and on our website, slot on the handle side and pop out the trim molding. subzero.com. Refer to the illustration below. If the thickness of the custom panel is less than a "...
  • Page 41 Model WS-30 Installation subzero.com Framed Panel Framed Panel Specifications RAISED PANEL With some door panel designs, you may have to rout, recess or use optional extended handles to allow for finger clearance. This is particularly true if your unit has raised panels greater than "...
  • Page 42 Additional panel design infor- mation can be found in the Sub-Zero wine storage design BACKER PANEL BACKER guide and on our website, subzero.com. PANEL TRIM IMPORTANT NOTE: The size of the overlay panel is critical. It must fit over the door frame. The weight of the "...
  • Page 43 Model WS-30 Installation subzero.com Overlay Panels Overlay Panels Specifications GRILLE PANEL ASSEMBLY Remove the grille panel assembly as described on page 33. Remove the top two corner screws and pull away the top frame. Slide the panel into position in the grille frame.
  • Page 44 Additional panel design infor- mation can be found in the Sub-Zero design guide and on BACKER PANEL BACKER our website, subzero.com. PANEL TRIM IMPORTANT NOTE: The size of the flush inset panel is critical. It must fit over the door frame. The weight of the "...
  • Page 45 Model WS-30 Installation subzero.com Flush Inset Panels Flush Inset Panels Specifications Remove the grille panel assembly as described on page 33. Remove the top two corner screws and pull away the top frame. Slide the panel into position in the grille frame.
  • Page 46 For additional information on panel reveals, visit the speci- relative to the installation, call Sub-Zero at 800-222-7820. fication library section of our website, subzerotrade.com. To obtain local dealer information, visit the showroom locator section of our website, subzero.com. Panel Offsets Illus. MODEL WS-30...
  • Page 47 Model WS-30 Installation subzero.com Dual Installations Flush Inset Panels—Dual Installation DUAL FLUSH INSET INSTALLATIONS Installing two models WS-30 or a model WS-30 and built-in unit side by side in a flush inset application will require adjustments to the dimensions of your finished rough opening, panel sizes and panel offsets.
  • Page 48 Model WS-30 Installation Flush Inset Panels—Dual Installation When installing two models WS-30 or a model WS-30 and TOP VIEW TOP VIEW built-in unit side by side in a flush inset application, you DOOR / DRAWER / GRILLE DUAL must decrease the width of the decorative flush inset TRIM panels by ".
  • Page 49 IMPORTANT NOTE: The overall height on the side panel section of our website, subzero.com. will vary with the height of the grille being used. Make sure IMPORTANT NOTE: The use of side panels may change you know your finished height before cutting any panels.

  • Page 50: Installation Checklist

    Have you given your customer the warranty package? customer service at 800-222-7820. You may also check the contact & support section of our website, subzero.com. Have any installation or service problems been noted on the product registration card? Has the registration...

  • Page 51: Service Information

    When calling for service, you will need the model and serial number of your unit. Both numbers are listed on the product rating plate. For models 424 and 424FS, the rating plate is located on the underside of the top wall. For models 427, 427R and WS-30, it is attached to the under- side of the control panel.
  • Page 52 SUB-ZERO, INC. P. O. BOX 44130 MADISON, WI 53744 SUBZERO.COM 800.222.7820 7011714 11/2008...

This manual is also suitable for:

424fs427427rWs-30