Related Manuals for Artel FiberLink 3516
Summary of Contents for Artel FiberLink 3516
- Page 1 MANUAL FiberLink® 3500 Series Transceivers 2 or 4 Channel 3G/HD/SD-SDI Transmission over one or two single mode or multimode fibers Installation and Operations Manual WWW.ARTEL.COM...
-
Page 2: Table Of Contents
Contents FiberLink 3500 Series Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Features . -
Page 3: Welcome
FiberLink 3500 Series Welcome Thank you for purchasing Artel Video Systems’ FiberLink 3500 Series . The 3500 Series is used to transmit up to 4 channels of 3G/HD/SD-SDI with or without pre-embedded au- dio and data over a single or dual fiber optic core . The FiberLink 3500 Series is compat- ible with single mode or multimode fiber . -
Page 4: Part Number Specifications
Technical Specifications FiberLink 3500 Series Part Number Specifications Part Number Specification for Transceiver Pairs Part Number Pairs with Part Number 3516 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3517 3518 . -
Page 5: General Specifications
Technical Specifications FiberLink 3500 Series General Specifications Indicators Power, HD/3G data rate lock, SD/DVB-ASI data rate lock, Alarm (Card version) Box Version Dimensions 6 .5W x 1 .15H x 6L (in) 165W x 29H x 152L (mm) Weight 12 .3 ounces, 382 grams Number of slots 3516, 3517, 3526 1 Slot... -
Page 6: Optical Output
Technical Specifications FiberLink 3500 Series 3500 Transmitter Section Specs * (cont.) Overshoot <10% of Amplitude Timing Jitter <0 .2 UI at 270Mbps; <1 .0 UI at 1 .485 Gbps; <2 .0 UI at 2 .97 Gbps with color bar signal applied Alignment Jitter <0 .2UI at 270Mbps, <0 .2UI at 1 .485 Gbps;... -
Page 7: Operating Loss Budget
** Distance specifications are approximate, based upon connecting a 3500 Transmitter to a 3500 Receiver, and are not guaranteed . Artel cannot estimate or guarantee operating loss budgets when the 3500 Series is used with other, non-FiberLink devices . Operating loss budget must not be exceeded . See data sheet for your specific model(s) . -
Page 8: Installation Instructions
Installation Instructions FiberLink 3500 Series Installation Instructions The FiberLink 3500 Series of fiber optic transmission systems are ready for immediate use and do not require any special tools or equipment . However, an Optical Power Meter, such as the FiberLink 6650, can be useful in determining optical loss budgets during your systems design and maintenance . -
Page 9: Alarm Switch Settings & Options
Alarm Switch Settings & Options FiberLink 3500 Series Alarm Switch Settings & Options The Rack Card version of this product has an additional red indicator LED that illuminates when an alarm condition exists . The rack card unit also provides an output to drive a model 6020A Alarm Sensing Module which provides an audible tone and activates a set of contacts for external signaling purposes . -
Page 10: Indicator Leds
LED Indicators FiberLink 3500 Series Indicator LEDs The FiberLink 3500 Series has integral indicator LEDs that are used to monitor the state of the unit . Card versions have an additional Alarm LED . Transmitter LEDs (For Each Channel) Status Definition Power Indicates that correct power has been applied. -
Page 11: Operating Pointers
Operating Pointers | Troubleshooting FiberLink 3500 Series Operating Pointers Remember to check attenuation of the fiber optic cable . The system will only operate properly if these specifications fall within the range of the system’s loss budget . Note: If no signal is applied to the 3500 Transmitter, no optical power will be present on the 3500 Transmitter’s output . -
Page 12: Maintenance And Repairs
. They have been designed for long, reliable and trouble-free service and are not normally field repairable . Should difficulty be encountered, Artel Video Systems maintains a complete service facility to render accurate, timely and reliable service of all products . -
Page 13: Fiberlink 6656 Visible Light Source
Accessories and Related Products FiberLink 3500 Series FiberLink 6656 Visible Light Source The FiberLink Visible Light Source provides a visible 650 nm laser output that can be used for identifying fiber breaks and individual fibers within fiber bundles, allow- ing for convenient, on-site testing of fiber networks dur- ing construction and maintenance procedures . -
Page 14: Related Products
Available in card versions and a small footprint box version, it is ideal for broadcast or cor- porate studios, OB vans, rental and staging, auditoriums, stadiums and theaters, airport or transportation hubs, distance learning, surgical or medical imaging and more Learn more at artel.com Page 14 FiberLink 3500 Bi-Directional Series User’s Manual... - Page 15 Accessories and Related Products FiberLink 3500 Series FiberLink 3500 Bi-Directional Series User’s Manual Page 15...
- Page 16 Solutions for most video, audio, and data formats Multimode and single mode versions Designed and manufactured in the USA Training and installation support available 24x7x365 technical support available Artel Video Systems Corp. 5B Lyberty Way, Westford, MA 01886 USA T: 978-263-5775 All specifications subject to F: 978-263-9755 change without notice .
Need help?
Do you have a question about the FiberLink 3516 and is the answer not in the manual?
Questions and answers