Advanced Timer Recording; Code; (Analogue Broadcast Only); Manually Programming Timer Recordings - Panasonic Diga DMR-EX78 Operating Instructions Manual

Advanced timer recording

[HDD] [RAM] [-R] [-RW‹V›] [+R] [+RW]
≥You can enter up to 32 programmes up to a month in advance.
(Each daily or weekly programme is counted as one programme.)
[RAM] [-RW‹V›] [+R] [+RW]
≥To use a new disc, formatting is necessary.
Preparation
≥Turn on the television and select the appropriate AV input to suit
the connections to this unit.
≥If recording to DVD, insert a disc that you can use for recording
(➡ 14).
≥Make sure that the clock settings are correct (➡ 65).
Using G-

CODE

recordings (Analogue broadcast only)
Entering G- numbers is an easy way of timer recording. You can
CODE
find these numbers in TV listings in newspapers and magazines.
1
Press [G-Code].
G-Code Remain HDD
Record
Input G-Code Number 0-9, and press OK.
2
Press the numbered buttons to enter
the G-
CODE
Press [2] to move back to correct a digit.
3
Press [OK].
Timer Remain HDD
Recording
Name Date Start
2A ARD 15. 10. WED 22:00
All Services : ARD
≥Confirm the programme (start and end time) by using a TV
magazine, etc. and make corrections if necessary using
[3, 4, 2, 1] (➡ right, step 3).
≥When "-- ---" appears in the "Name" column, you cannot set
timer recording. Press [3, 4] to select desired programme
position. After you have entered the information of a TV
station, it is kept in the unit's memory.
4
Press [OK].
The timer programme is stored and the timer icon is
displayed.
Timer icon
"F" lights on the unit's display to indicate timer recording
standby has been activated.
TUE 14.10.08. 12:56:00
HDD
Stop Mode
DVD
20:00 HDD SP
Programme
Repeat steps 1–4 to programme other recordings.
Press [ DVD] to turn the unit off.
RQT9088
24
system to make timer
G- is a registered trademark of
CODE
Gemstar Development Corporation. The
G- system is manufactured under
CODE
license from Gemstar Development
Corporation.
30:24 SP DVD 1:58 SP
TUE 14.10.08. 12:53:00
number.
30:24 SP DVD 1:58 SP
TUE 14.10.08. 12:54:00
HDD
Mode
Stop
DVD
22:30 HDD SP
Programme Name
No. Name
&
01
Drive
space
Check to make sure "OK"
OK
is displayed (➡ 25).
Manually programming timer
recordings
1
Press [PROG/CHECK].
2
Press [3, 4] to select "New Timer
Programme" and press [OK].
3
Press [1] to move through the items
and change the items with [3, 4].
≥When "Name" is selected, you can press the "Blue" button to
change the group [e.g., TV, Radio, Edit Favourites screen
(➡ 59)] and then press [3, 4] to select the channel you
want to record.
≥Press and hold [3, 4] to alter the Start (Start time) and
Stop (Finish time) in 30-minute increments.
≥You can also set Name (Programme position/TV Station
Name), Date, Start (Start time), and Stop (Finish time) with
the numbered buttons.
≥Date
[.
Date:
l
;:
l
Daily timer:
l
;:
l
a.
Weekly timer: SUN>--->SAT
Titles recorded using the same daily or weekly timer are
bundled and displayed as a "group" in the Direct Navigator
screen (➡ 29) except when using Auto Renewal Recording.
≥You can also press [DRIVE SELECT] to select the recording
drive.
When the recording drive is "DVD" and there is not enough
remaining space, recording automatically switches to the
"HDD" (➡ 26, Relief Recording).
≥You can also press [REC MODE] to change the recording
mode.
≥[HDD] RENEW (Auto Renewal Recording) (➡ 26)
ON!)OFF
≥Programme Name
Press [2, 1] to select "Programme Name" and press [OK].
(➡ 44, Entering text)
4
Press [OK].
The timer programme is stored and the timer icon is
displayed.
"F" lights on the unit's display to indicate timer recording
standby has been activated.
Repeat steps 2–4 to programme other recordings.
Press [ DVD] to turn the unit off.
ARD
Current date up to one month later minus
one day
SUN-SAT>MON-SAT>MON-FRI
No. Name
&
01
Timer icon
ARD