Table of Contents
Advertisement
Quick Links
5 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand the procedure
required to enable your vehicle in such situations. In addition, the chart on the last
page of this manual has a section for the particular features and options installed
in your vehicle as well as the override method selected. Although the default
mode is "Valet Switch" operation, the system can be configured for "Custom
Code" operation for enhanced security. Confirm the override mode selected on
the last page of this manual, and familiarize yourself with the section on it's opera-
tion.
FEATURES :
1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control
Six Channel Code Learning Programmable Receiver
External Superheterodyne Transceiver Antenna
Single Or Two User Programmable W/Separate Control Outputs
Single Button Lock/Unlock or Separate Button Lock/Unlock or Both
Remote Keyless Entry With Optional Access Guard (must have power door
locks)
Selectable Manual Override Mode
New Enhanced Panic Feature (Any button other than unlock stops siren, no
change to the units state)
Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )
Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect
Off, City Mode)
Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or
For R/S)
24 Hour Time Start Mode
Cold Temperature Start Mode
2 or 4 Hour Automatic Start Mode
Parking Meter Count Down Timer On LCD Remote
Additional Count Down Timer Mode
Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds
To Engage)
Improved Custom Code Override, User Selectable and Programmable
Model APS-997N
Owner's Manual
Page 1
128-8549
1 of 24
Advertisement
Table of Contents
Related Manuals for Audiovox Prestige Platinum 128-8549
Summary of Contents for Audiovox Prestige Platinum 128-8549
- Page 1 5 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable IMPORTANT ! In order to provide you with the highest level of security to your vehicle, this system is equipped with selectable manual override circuitry. It is possible that you will need to override you security system if the transmitter becomes lost, or inoperative due to battery failure.
-
Page 2: Your "Code Hopping" Transmitters
Protected Push Button Valet/Override Switch 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming Intrusion Alert With Memory Instant Siren Activation Starter Disable Output Additional Engine Immobilizer Output, (Optional Relay Required) ... -
Page 3: Arming The System - Active
known as a code grabber, which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system. Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then re-transmits your signal, the alarm system will not respond. -
Page 4: Arming The System - Passive (Automatic)
The dash mounted LED begins to flash slowly. Parking Lights flash one time. Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. -
Page 5: Disarming The System
Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle. NOTE: If the optional interior illumination circuit was installed, the interior light will flash as well for the full 30 second alarm cycle. -
Page 6: While The System Is Sounding
Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. Siren will not sound. If the siren sounds 4 chirps, then the alarm was triggered in your absence. - Page 7 NOTE: Always remember to return the vehicle to the valet off position. This will ensure that the vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM: USING THE PBLED OVERRIDE SWITCH Your Security System can be disarmed without the use of the keychain transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails.
-
Page 8: Eliminating The Normal Arm/Disarm Chirps
3. Within 10 seconds, press and release the PBLED switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Within 10 seconds, begin to press and release the PBLED switch to set the tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5) 6. -
Page 9: Remote Panic Operation
important warnings to you that something has happened, they cannot be eliminated. NOTE: Your system must be programmed by the installation center to en- able this feature. REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations. -
Page 10: Remote Starting The Vehicle
1. Within 2 seconds of arming, press and release the ARM button 1 time, to defeat the pre-detect stage of the shock sensor. (The lights will flash and the siren will chirp once.) 2. Within 2 seconds of step 1, press and release the ARM button 2 times, to defeat the pre and full detect stages of the shock sensor. -
Page 11: Operating On Automatic Start Up Timer Mode
When you arrive at your vehicle, disarm the alarm system by pressing and re- leasing the arm/disarm button of your keychain transmitter. Enter the vehicle and turn the ignition key to the on position. CAUTION! Do not turn the key to the start position. This will cause the starter motor to engage with the already running engine which could result in damage. - Page 12 NOTE: Option button used in combination is only available on the alternate re- mote transmitter and not available on the LCD Transmitter. OPTIONAL DEVICE OUTPUT ( CHANNEL 3 ) Controlled By: Trunk/Key Button Other Transmitter button configurations are also available. Consult your installa- tion center for other configurations not listed above that may have been pro- grammed to operate a specific feature of your system.
-
Page 13: Turbo Timer Mode
Controlled By: Trunk/Key Button Option Button Lock + Unlock Buttons Lock + Trunk/Key Buttons Unlock + Trunk/Key Buttons Other Transmitter button configurations are also available. Consult your installa- tion center for other configurations not listed above that may have been programmed to operate a specific feature of your system. -
Page 14: Telematic Upgrade
With the turbo timer mode selected on, after you've arrived at your destination, while the engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch to the off position. The engine will continue to run the allotted time according to the selection during installation. - Page 15 When the Panic Mode has been activated and the system is armed the vehicle's lights will flash, the siren and lock icon will be displayed on the LCD screen and the siren will beep. If the system is disarmed and the Panic Mode is activated, the lights will flash unlock icon will be displayed and the siren will beep on the LCD screen.
- Page 16 When the vehicle is armed, and a door is opened, or ajar, the transmitter will chirp 3 times, the lights will flash, and the display will indicate a door trigger as shown on the previous page. When the door is closed or the zone clears, the transmitter will chirp 1 time, and the display will clear.
- Page 17 ADDITIONAL REMOTE FEATURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selection of these and other features are shown below: NOTE: Transmitter must be within operating range of the vehicle, approximately 1000 ft.
- Page 18 set time. To toggle this feature off, press the option + lock buttons simulta- neously until a beep is heard and the 24 hr timer turns off. Note: the unit will start once and run for the prescribed time. If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide.
- Page 19 corner of the screen as shown left. This icon indicates a new battery shown with 3 bars. As the battery deteriorates, the bars will disappear. 1 bar indicates the battery should be replaced. Replace battery with a fresh 1.5V AAA battery and dispose of the used battery properly. Other icons that will be displayed at times when certain functions and features are active in the vehicle or on the remote: Range Indicator.
- Page 20 THIS PAGE LEFT BLANK INTENTIONALLY Page 20 128-8549 20 of 24...
- Page 21 Page 21 128-8549 21 of 24...
- Page 22 THIS PAGE LEFT BLANK INTENTIONALLY Page 22 128-8549 22 of 24...
- Page 23 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING REARMING SLOW FLASHING ON SOLID 3 FLASH...PAUSE 2 FLASH...PAUSE 1 FLASH...PAUSE SIREN CHIRP INDICATORS 1 CHIRP * 2 CHIRPS * 3 CHIRPS 4 CHIRPS * These chirps are optional, and can be de - activated. PARKING LAMP INDICATORS 1 FLASH 2 FLASHES...
- Page 24 © 2009 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-8549 Page 24 128-8549 24 of 24...