Table of Contents
Advertisement
Quick Links
1.1 Product Features ....................................................................................1
1.2 Unpacking..............................................................................................2
1.3 Physical Environmental Requirements ..................................................2
1.4 Panel and LED Indicators ......................................................................3
3.1 Configuration on the main Interface ......................................................8
3.2
3.3 Use Fixed IP Address to Connect the Internet......................................11
3.4 Use External Dial-up Software to Connect to the Internet...................13
4.1 LAN Configuration..............................................................................20
4.2 Admin Setting......................................................................................23
........................................................................ 26
5.1 Q: How to judge if the ADSL2+ is connected normally? .......................26
5.2 Q: What is Virtual dial-up? .....................................................................26
5.3 Q: I am the user of ADSL2+, but sometimes I can't have access to the
Internet, why? ...............................................................................................26
5.6Q: Can ADSL2+ support sharing internet access in the LAN? ................27
5.7Q:
5.8Q:
......................................................................................................................28
Table of Contents
.................................. 1
..................... 19
... 7
9
................28
Advertisement
Table of Contents
Related Manuals for Tenda TED8620R
Summary of Contents for Tenda TED8620R
-
Page 1: Table Of Contents
Use Built-in Dial-up Software to Connect to Internet 3.3 Use Fixed IP Address to Connect the Internet........11 3.4 Use External Dial-up Software to Connect to the Internet....13 ..... 19 Chapter Four TED8620R+ Advanced configuration 4.1 LAN Configuration................20 4.2 Admin Setting..................23 ................ 26 5.1 Q: How to judge if the ADSL2+ is connected normally? .......26... -
Page 2: Chapter One Ted8620R+ Introduction
TED8620R + ADSL User’s manual Chapter One Introduction 1.1 Product Features Welcome to use Tenda TED8620R +MODEM 1.1.1 Features Wired-speed, auto-negotiation ADSL2+ Modem, supports bridge/ routing mode. MAX downstream: 24Mbps/ upstream:1Mbps Max transmission distance: 6.5KM； Complete and friendly user configuration interface, compliant with currently popular Server/Browser mode. -
Page 3: Unpacking
TED8620R + ADSL User’s manual RFC 1483 Bridge、RFC 1483 Router supported Classical IP over ATM (RFC 1577) supported PPP over ATM(RFC 2364) supported PPP over Ethernet (RFC 2516) supported 1.2 Unpacking Please unpack and you would find the following items: TED8620R+ Modem one unit User’s manual one copy... -
Page 4: Panel And Led Indicators
1.4 Panel and LED Indicators 1.4.1 Description of Panel and LED Indicators Figure 1.1 TED8620R+ Panel TED8620R+ has 5LED indicators, through checking the status of the LED lights, we can judge whether the Modem is working normally. They indicate as follows:... - Page 5 TED8620R + ADSL User’s manual TED8620R+ is receiving or transmitting LAN_ACT Blinking data with the NIC or the switch. ADSL2+ connection established successfully ADSL2+ connection is not established ADSL2+_LINK Blinking successfully Fast Handshaking to try to establish ADSL2+ Blinking connection...
-
Page 6: Chapter Two Hardware Installation
If you are using splitter, please connect the ADSL2+ telephone line to the LINE interface of the splitter, connect the telephone to the PHONE interface of the splitter, and connect the LINE interface of TED8620R+ together with the MODEM interface of the splitter. - Page 7 TED8620R + ADSL User’s manual Device Connection Figure...
-
Page 8: Chapter Three Configuration For Access To The Internet
TED8620R + ADSL User’s manual Chapter Three Configuration for Access to the Internet TED8620R+ is plug and play device, there are six bridge modes in the setting, you can directly use external dial-up software or router dial-up to connect to Internet without making any configuration. -
Page 9: Configuration On The Main Interface
TED8620R + ADSL User’s manual 3.1 Configuration on the main Interface After correctly entering the user name and password, the following interface will appear on your screen:... -
Page 10: Use Built-In Dial-Up Software To Connect To Internet
TED8620R + ADSL User’s manual In this Interface, we can see that there are 6 bridges modes for WAN connecting. For each bridge mode, their parameters are different. Please pay attention to the VPI and VCI or the local ISP. In configuration, we can not add two groups with the same VCI and VPI parameters. - Page 11 TED8620R + ADSL User’s manual Before setting 3.2.1 Before setting, user should obtain the following parameter from your ISP: VCI, VPI, access method and encapsulation format (in mainland China, encapsulation is usually PPPOE-LLC), account for dialing up and password. 3.2.2 ADSL2+ MODEM Parameter Setting Please Press the “Quick Configuration”...
-
Page 12: Use Fixed Ip Address To Connect The Internet
TED8620R + ADSL User’s manual We will introduce how to modify the parameter. First we choose “1” as the ATM Interface. The choose “Enabled” as Operation Modes, “PPPoE LLC” as encapsulation, “Disabled” as Bridge, “Enabled” as “DHCP”, “Enable” as Default Route. And use default value for other options. And please the account number and password correctly. - Page 13 TED8620R + ADSL User’s manual connecting to the Internet, Subnet mask, Gateway, and DNS. 3.3.2 Configuration on the Modem Please click Quick Configuration and you would see the following Interface. Encapsulation In Operating Modes, please select “Enabled”, In “ ”, please enter Encapsulation, VIP, VCI.
-
Page 14: Use External Dial-Up Software To Connect To The Internet
TED8620R + ADSL User’s manual administration interface to save the parameters that you set, they will lose next time when you restart the modem. And you have to configure again. 3.4 Use External Dial-up Software to Connect to the Internet 3.4.1 Before setting... - Page 15 TED8620R + ADSL User’s manual The following dialogue box would appear, please click “Next” to continue. After this, the following Interface would appear, please click “Yes”.
- Page 16 TED8620R + ADSL User’s manual Please click “Next” in the following dialogue box. In the dialogue box below, please choose the directory for installation. You could click “Next” as selecting the default directory and continue.
- Page 17 TED8620R + ADSL User’s manual Please click “OK” in the following dialogue box. If the following dialogue box appears, please insert the installation CD of Windows 98 and then click “OK”.
- Page 18 TED8620R + ADSL User’s manual If your Windows 98 operating system is copied on the hard disk, please enter the directory where the Windows 98 system is located in then blank place and then click “OK” to continue. Finally, the following dialogue box would appear, please single click “Finish”...
- Page 19 TED8620R + ADSL User’s manual 3.4.3 ADSL2+ MODEM Parameter Setting for External Dialup Software In Quick Configuration Interface, please configure as follows: Please select “Enabled” for Operating Mode; “1483 Bridged IP LLC” for Encapsulation; input “35” for VPI, “8” for VCI, then please click submit.
-
Page 20: Chapter Four Ted8620R+ Advanced Configuration
TED8620R + ADSL User’s manual 3.4.4 Dial-up to Connect to the Internet When the dialup software is installed successfully and the parameters for ADSL2+ are configured correctly, you are able to use the installed dialup software to dialup to have access to the Internet. -
Page 21: Lan Configuration
TED8620R + ADSL User’s manual 4.1 LAN Configuration This section is for the configuration of LAN. You would set the related parameters as the sign of your equipment in the network. 4.1.1 LAN Configuration Get LAN Address: On this option, the default setting is manual. - Page 22 TED8620R + ADSL User’s manual 4.1.2 DHCP Server Configuration When you modify the IP Address for ADSL2+ Modem, or the current IP addresses are not enough, you would set in this option. Click DHCP server to access the setting interface. If you want to add IP pool, Please click “Add”.
- Page 23 TED8620R + ADSL User’s manual 4.1.3 DHCP Server Pool-Adding When you prepare to add IP address or IP pool, you could see the following interface. In this interface, please input start IP address, End IP address, and subnet mask. Click ‘Save’. (When adding, the start IP address would not be the same as existing end IP address.) You needn’t set the other...
-
Page 24: Admin Setting
TED8620R + ADSL User’s manual 4.2 Admin Setting This interface is the menu for administrator to have configuration. There are User Configuration, Commit and reboot, Local image upgrade, Remote image upgrade, Diagnostics, Port setting, System Log, Backup and restore Config. - Page 25 TED8620R + ADSL User’s manual Commit & Reboot: This page is used to save the existing modifications or Reboot to restore according to different configuration. Save the modification: Choose “Reboot” under reboot mode, and click “Commit”. Note: No matter in which menu you modify, you should access this interface for saving.
- Page 26 Firmware Upgrade: To upgrade the system firmware. When you obtain the latest upgrading firmware for ADSL2+ Modem (download from our homepage www.tenda.cn, or from our distributors), please upload the related file to upgrade. Note: Please don’t turn off the power or stop during upgrading, or the irreversible physical damage would happen, and the ADSL2+ Modem would doesn’t work.
-
Page 27: Faq
TED8620R + ADSL User’s manual 5.1 How to judge if the ADSL2+ is connected normally? When the hardware is connected correctly and the line is normal. The ‘”ADSL2+LINK”indicator should be indicated as ON. Or, the indicator would be blinking. Blinking indicates line error or error in connector. Please connect the lines again or contact your local ISP. -
Page 28: Q: I Am Far Away From The Telephone Office, Can I Still Use Adsl2
TED8620R + ADSL User’s manual equipment for telephone guard. 5.4 I am far away from the telephone office, can I still use ADSL2+? For ADSL2+, the efficient distance between the telephone and CPE is within 6.5 kilometers. So, please kindly take this point into account. To make sure of the communication quality, it’s better to keep the distance within 3 kilometers. -
Page 29: How To Set And Obtain Dynamic Ip For Lan Users
LAN is in the same segment as TED8620R+, and set the gateway as the one of TED8620R+. Also, you would adopt “Auto-obtain IP”. And the TED8620R+ would distribute IP and gateway automatically.