Download Print this page

Yamaha DTX720K Assembly Manual

Advertisement

Quick Links

ELECTRONIC DRUM KIT
DTX582K/DTX720K
This manual describes the standard assembly procedure for the DTX582K/DTX720K electronic drum kits. It covers assembly and wiring of the kit as shown below.
When you have completed all of the steps described, you will be ready to turn on the drum trigger module and start playing.
Illustrations show the DTX502 drum trigger module.
IMPORTANT
This manual describes the process of assembling a drum-pad set and drum trigger module to an already assembled RS502
Electronic Drum Rack. Before starting the steps below, therefore, be sure to assemble your RS502 as described in the Owner's
Manual that came with it.
Example of standard assembly
Cymbal pad
Tom pads
Real Hi-hat Pad
DTX502/DTX700
Drum trigger module
Hi-hat stand
Kick pad
Snare pad
Safety Precautions
The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating the severity and immediacy
of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The instructions displayed together with these precautions
are extremely important in terms of ensuring safety, and therefore, they should be fully observed.
* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.
* Be sure to also read the Assembly Manuals and/or Owner's Manuals that came with your pads and rack.
Failure to observe the precautions described below can result in se-
WARNING
rious injury or even death.
• Young children using this electronic drum kit should be supervised by a guardian to eliminate any
possibility of injury.
• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should
take special care whenever handling these components.
• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-
fore, you should take special care whenever handling these components.
• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In
addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads
may fall off or the rack may collapse or fall over, possibly causing injury.
• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe
surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.
• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If
someone were to trip on a cable, the kit could topple over and cause injury.
• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to
observe this precaution can result in injury or malfunction.
• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing injury.
* Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time
without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
Manual Development Department
© 2015 Yamaha Corporation
Published 12/2015 POAP*.*-**A0
Printed in Vietnam
EN
Assembly Manual
ZU86750
NOTICE
Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can
place cardboard from the drum kit packaging or the like on the floor to prevent it from being
scratched. This is particularly important when using the HS650A Hi-hat Stand and KP100
Kick Pad.
NOTE
If using double foot pedals and want to position them relatively far apart from one another,
please setup as shown below.
Cymbal pad
Tom pad
Electronic drum rack
Please read carefully before proceeding.
Failure to observe the precautions described below can result in in-
CAUTION
jury and/or property damage.
• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during
this operation.
• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by
sharp tips if these components are not handled carefully.
• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.
• Do not use the electronic drum kit's rack to hold acoustic drums. Doing so could cause clamps to
break and the drums to fall off, which in turn could lead to injury.
NOTICE:
Usage Precautions
• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In addition,
avoid placing heavy items on top of cables and do not allow them to touch sharp edges. Failure to avoid
these precautions can lead to cable breakage and disconnection.
• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe this pre-
caution can result in malfunction.
• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close proximity to
a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or outdoors in wet weather).
Failure to observe this precaution can lead to warping, discoloration, malfunction, or breakdown.
• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these substances
can cause warping and discoloration. Instead, we recommend you remove dust using a soft dry cloth or
wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first wipe the dirt away
using a cloth moistened with a neutral detergent solution and tightly wrung. Following this, wipe away the
detergent solution using a cloth soaked in water and tightly wrung.
1
Open the boxes to reveal their contents.
After opening up the packages containing your electronic drum kit, please verify that all of the following components are present.
Components of DTX582K/DTX720K
 XP80 Snare Pad
 PCY135 Cymbal
 RHH135 Real
(x1)
Pad (x2)
Hi-Hat Pad (x1)
 HS650A Hi-hat
 KP100 Kick Pad (x1)
Stand (x1)
 Nine-channel snake cable (x1)
 XP70 Tom Pad (x3)
 Clamp bolt
 DTX582K/DTX720K Assembly Manual (this booklet; x1)
 PCY100/135/155 Owner's Manual (x1)
(for XP70 or XP80; x4)
 RHH135 Owner's Manual (x1)
 XP70/80 Owner's Manual (x1)
 KP100 Owner's Manual (x1)
Assemble the RS502 Electronic Drum Rack.
2
For instructions on how to assemble the RS502 Electronic Drum Rack, refer to the Owner's Manual that came with it.
3
Assemble the pads and the drum trigger module to the electronic drum rack.
Assembling the snare and tom pads
2.
Push the snare pad onto the rack's snare holder. Ensure that
Tom pads
the rod section is fully inserted into the snare pad's mounting
XP70
hole, and then tighten the clamp bolt to secure the pad in
place.
3.
Loosen bolts A to D as shown below to adjust the height and
XP80 Snare Pad
angle of the snare pad. When correctly positioned, be sure to
securely retighten the bolts before proceeding to the next
step.
Snare pad
1.
Attach a clamp bolt to the snare pad and provisionally tighten
(by five or six turns).
Clamp bolt (tighten in the
direction of the arrow)
Snare pad (rear side)
1
 Stand base for
 Hi-hat clutch for
 RS502 Electronic Drum Rack (x1)
RHH135 (x1)
RHH135 (x1)
 RS502 Owner's Manual (x1)
 Stopper for
 Felt pad for
PCY135 (x2)
PCY135 (x2)
 Cable band
 Cable band for
(x6)
RHH135 (x1)
 DTX502/DTX700 Drum Trigger
Module (x1)
 Tuning key (x1)
 Power adaptor (x1)
* May not be included depending on
your particular area. Please check
with your Yamaha dealer.
 DTX502/DTX700 Owner's Manual
(x1)
Tom pads
1.
As with the snare pad, attach a clamp bolt to each of the three
tom pads and provisionally tighten (by five or six turns).
2.
Push each of the tom pads onto one of the rack's tom holders.
Snare pad
Each time, ensure that the tom holder's rod is fully inserted
into the tom pad's mounting hole, and then tighten the bolt to
Snare holder
Rod section
secure the pad in place.
Tom pad: XP70
Insert
Clamp bolt
Clamp bolt
3.
Loosen bolts A to C as shown below to adjust the height and
angle of each tom pad. When correctly positioned, be sure to
Bolt B
securely retighten the bolts before proceeding to the next
step.
Bolt D
Bolt C
Bolt A
Bolt A
 Module holder (x1)
* The illustration shows the
DTX502 module holder.
 Module holder screw
(x2 for DTX502 / x4 for DTX700)
Rod section
Insert
Tom holder
Bolt B
Bolt C
Continued on other side

Advertisement

loading

Summary of Contents for Yamaha DTX720K

  • Page 1 * Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
  • Page 2 * For detailed instructions, refer to the Setting Up section Select the “DTX582K” trigger setup on the DTX502 drum trigger module. (For details on the trigger Select the “DTX720K” trigger setup on the DTX700 drum trigger module. (For details on the trigger Footboard stabilizer rod in the RHH135 Owner’s Manual.

This manual is also suitable for:

Dtx582k