DeWalt DWS771 Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Saw
  5. DWS771
  6. Manual

DeWalt DWS771 Manual

Sliding mitre saw
Hide thumbs Also See for DWS771:
Table of Contents

Advertisement

Quick Links

DWS771
DWS777
Final Page Size: 210 x 297 mm

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DWS771

Summary of Contents for DeWalt DWS771

  • Page 1 DWS771 DWS777 Final Page Size: 210 x 297 mm...
  • Page 2 English (original instructions)
  • Page 3 Figure A DWS771 Figure B 00-00-0000...
  • Page 4 Figure D Figure C Figure E Figure F Figure G Figure H Figure I Figure J...
  • Page 5 Figure K Figure L Figure M Figure N Figure O Figure P...
  • Page 6 Figure Q Figure R Figure T Figure S Figure U Figure V...
  • Page 7 Figure W Figure X...

  • Page 8: Safety Instructions

    English CROSS-CUT MITRE SAW Denotes risk of electric shock. DWS771, DWS777 Denotes risk of fire. Congratulations! Denotes sharp edges. You have chosen a D WALT tool. Years of experience, thorough product development and EC-Declaration of Conformity innovation make D WALT one of the most reliable partners for professional power tool users.

  • Page 9: Additional Safety Rules For Mitre Saws

    English 13 . Do not overreach. • Disconnect the machine from the mains before carrying out any maintenance work or when Keep proper footing and balance at all times. changing the blade. 14 . Maintain tools with care. • Never perform any cleaning or maintenance work when the machine is still running and the Keep cutting tools sharp and clean for better and safer performance.

  • Page 10: Package Contents

    DWS777 / DWS771: H05RN-F, 2x1.0 mm² or changing set-ups or when making repairs. Be sure the trigger switch is in the OFF DWS777 LX / DWS771 LX: H05RR-F, 2x1.5 mm² position. An accidental start-up can cause injury. Mains Plug Replacement Your mitre saw was accurately adjusted at the factory.

  • Page 11: Prior To Operation

    Loosen the screws   51 and move the scale/mitre arm assembly left or right until the Speed Control Dial (DWS771 only) blade is at 90° to the fence as measured with the square (Fig. N). The speed control dial   29 can be used for advance setting of the required range of speed.

  • Page 12: Cutting Large Material

    English WARNING: When mitring the end of a piece of wood Always try cuts on a few scrap pieces of wood with a small off-cut, position the wood to ensure that the off-cut is to the side of the blade to verify the settings on the saw.

  • Page 13: Protecting The Environment

    English Cleaning Before use, carefully check the upper blade guard, movable lower blade guard as well as the dust extraction tube to determine that it will operate properly. Ensure that chips, dust or workpiece particle cannot lead to blockage of one of the functions. In case of workpiece fragments jammed between saw blade and guards disconnect the machine from the power supply and follow the instructions given in section Mounting the saw blade.
  • Page 16 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...

This manual is also suitable for:

Dws777

Table of Contents