McIntosh MC352 Owner's Manual
Hide thumbs Also See for MC352:

Advertisement

OWNER’S
MANUAL
MC352 Power Amplifier
MC352
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MC352 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for McIntosh MC352

  • Page 1 OWNER’S MANUAL MC352 Power Amplifier MC352 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549...
  • Page 2: Table Of Contents

    For assistance on factory repair return procedure, contact PIN 2: + input. the McIntosh Repair Department at: PIN 3: - input. 6. In the event that MC352 Power Amplifier over heats, due to McIntosh Laboratory, Inc. improper ventilation and/or extremely high ambient 2 Chambers Street temperature, the built in protection circuits will activate.
  • Page 3: Safety Instructions

    Safety Intructions IMPORTANT SAFETY INSTRUCTIONS! Attention: pour pevenir les chocs elecriques pas utiliser cette fiche polarisee avec un prolongateur, une prise de courant ou un autre sortie de courant, PLEASE READ THEM BEFORE sauf si les lames peuvent etre inserees afond ans en OPERATING THIS EQUIPMENT.
  • Page 4: Introduction

    McIntosh Sentry Monitor power output stage protection a qualified technician to restore the product to its normal operation. circuits ensure the MC352 will have a long and trouble free operating life. Built-in thermal protection circuits guard E. The equipment has been dropped or damaged in any against overheating.
  • Page 5: Installation

    A custom cabinet installation should provide the follow- ing minimum spacing dimensions for cool operation. Allow The MC352 can be placed upright on a table or shelf, at least 6 inches (15.24 cm) above the top, 2 inches standing on its four feet. It also can be custom installed in a (3.81cm) below the bottom and 1 inch (2.54 cm) on each...
  • Page 6: Rear Panel Controls And Connections

    MC352 Rear Panel Controls and Connections MC352 Rear Panel Controls and Connections BALANCED INPUTS for audio POWER CONTROL In receives cables from a preamplifier or turn on/off signals from a McIntosh control center audio outputs component and the POWER CON-...
  • Page 7: How To Connect

    Refer to figures 5 & 6. Note: The bare sections of the cable ends or the non 1. Connect the MC352 power cord to a live AC outlet. insulated part of the connectors must not be exposed on 2.
  • Page 8: Front Panel Displays And Controls

    MC352 Front Panel Displays and Controls MC352 Front Panel Displays and Controls METER indicates the Left Channel METER indicates the Right Channel Power Output of the amplifier Power Output of the amplifier POWER GUARD LED’s light when the amplifier channel POWER GUARD...
  • Page 9: How To Operate

    How to Operate the MC352 in Mono Note: There must be a power control connection between the The MC352 can be operated in Mono Mode as a 700 watt MC352 and the McIntosh Control Center, in order for amplifier with output impedances of 1, 2 and 4 ohms. Refer the remote power turn on to function.
  • Page 10: Specifications

    230 Volts, 50/60Hz at 6.25 amps Output Load Impedance 240 Volts, 50/60Hz at 6.00 amps 2, 4 or 8 ohms (Stereo Mode) NOTE: Refer to the rear panel of the MC352 for the correct 1, 2 or 4 ohms (Mono Mode) voltage. Rated Power Band...
  • Page 11: Packing Instruction

    If a shipping carton or any of the interior part(s) are needed, please call 101212 1/4-20 x 2-1/4” cap screw or write Customer Service Department of McIntosh Labo- 104058 Flat washer ratory. Please see the Part List for the correct part numbers.
  • Page 12 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 McIntosh Part No. 040626...

Table of Contents