Table of Contents
Advertisement
5
6. SERVICE MODE
QQ
3 7 63 1515 0
6.1 DVD TEST MODE
Image of the test mode.
Remote Control Assy SW: DVH
Start of the test mode.
]
FE test selection
Hereafter, to FE test
mode image.
[Note] In order to move on to another test after selecting a test (FE/EDC1/EDC2), it is necessary to restart the DVD mechanism in the test mode.
Image of the front end test mode.
FE test mode
TE
L 13942296513
0 x 00 0000
]
Power on
0FFF 0000
1 x 00 0000
]
F close
1FFF 0000
Focus close state
www
(2)
a
.
5
http://www.xiaoyu163.com
TEST
[Note] Higher level 4 characters only. Lower level 4 characters are spaces.
[
EDC1 test selection
Hereafter, to EDC1
test mode image.
[
FE offset coefficient
Disc type DVD1
TE offset coefficient
layer
AS offset coefficient
ENV offset coefficient
TG offset coefficient
0000 0000
DBAL coefficient
VIN1 offset cancel value
VIN2 offset cancel value
VIN3 offset cancel value
VIN4 offset cancel value
VIN5 offset cancel value
VIN6 offset cancel value
VIN7 offset cancel value
VIN8 offset cancel value
VIN9 offset cancel value
VIN10 offset cancel value
[
CRG+/-
F search
S curve
measurement
Activates while the key
1A00 0000
is being pressed.
1B00 0000 : CRG+
[
1C00 0000 : CRG-
F search
1100 0000
FEMAX level
FEMIN level
ASMAX level
ENVMAX level
FE normalization coefficient
Spindle gain coefficient
TEMAX level indication
TEMIN level indication
x
ao
y
i
http://www.xiaoyu163.com
6
8
Legend:
... Key operation
... Operation state
... The content displayed on the DVD mechanism (video only)
8 characters data is sent to the product side (HOST) by UART communication.
1
EDC2 test selection
Hereafter, to EDC2
test mode image.
Legend:
... Key operation
... Operation state
... The content displayed on the DVD mechanism (video only)
8 characters data is sent to the product side (HOST) by UART communication.
Q Q
3
6 7
1 3
1
2
Disc type DVD2
Disc type CD
layer
0100 0000
0200 0000
3
1, 2
LD-ON/OFF
When LO-ON: 1100 0000
When LD-OFF: 1000 000
[Note] If no action is taken for approximately 10 seconds after LD-ON, it will become LO-OFF automatically.
If F close is selected during LD-OFF, it will become an error.
During focus search (S character measurement mode), too, safety regulation applies if LD_OFF is not selected
within 10 seconds. Therefore, even if focus search is selected after LD-ON, it will become LD-OFF after 9 seconds.
In order to F close after focus search (S character measurement mode), set to Power_OFF first then power on again
before F close.
u163
.
DVH-P5900MP/XN/EW5
6
7
2 9
9 4
2 8
2
LD power on time
mode selection
Hereafter, to LD power on
time mode image.
1 5
0 5
8
2 9
9 4
3
Disc type CD-RW
0300 0000
4
CRG_HOME
Power_OFF
1D00 0000
m
co
7
8
9 9
A
B
C
2 8
9 9
EJECT
EJECT
D
6
E
b
F
51
8
Advertisement
Table of Contents
