Table of Contents
Advertisement
O O
O O
O O
O O
O O
O O
t t
t t
t t
t t
t t
t t
h h
h h
h h
h h
h h
h h
e e
e e
e e
e e
e e
e e
r r
r r
r r
r r
r r
r r
s s
s s
s s
s s
s s
s s
Notes and Hints
$ White Balance
In the following cases, you cannot change White
Balance:
OWhen you set the Picture Effect to [GAIN-UP],
[SEPIA] or [MONO].
OWhen you set the Zoom to 15a or higher
ODuring Digital Still Picture Mode
OWhen you display a Menu
In the following cases, the [
flashes:
OThe flashing indicates that the previously adjusted
White Balance setting is still kept.
This setting will be kept until White Balance is
adjusted again.
OYou may not be able to achieve correct White
Balance Adjustment manually under weak
illumination.
$ Manual Shutter Speed Adjustment
OYou may see vertical lines of light in the playback
image of a brightly shining subject or highly
reflective subject.
ODuring normal playback, movement in the images
may not look smooth.
OBecause the color and brightness of the playback
image may become unstable, avoid recording under
fluorescent light, mercury light or sodium light.
OIf you are using either Gain-up Mode (-29-) or
Program AE Mode (-26-), you cannot adjust the
shutter speed. If the shutter speed was adjusted
manually, this setting will be cancelled.
$ Manual Iris Adjustment
ODepending on zoom magnification, there are iris
values that will not be displayed.
OIf you are using Program AE Mode (-26-), you
cannot adjust the iris.
OIf you attempt to adjust the Shutter Speed after
setting the Iris, the value set for the Iris will be
cancelled.
$ Picture Effect Functions
OIf the Picture Effect is set to [WIPE], [MIX] or
[TRAIL] with [PIC.E.] Button, the setting of [NEGA],
[SEPIA], [MONO] or [SOLARI] is canceled.
OIf you have set the Picture Effect to [MONO] or
[SEPIA], changing the selected White Balance
Mode is not possible. (-27-)
OIf the Picture Effect is set to [GAIN-UP], the
previously adjusted shutter speed is canceled.
It is as follows when [GAIN-UP] is selected.
OManual Focus Mode
OThe shutter speed and White Balance cannot be
operated.
OThe Sports Mode [
], the Portrait Mode [
Low Light Mode [ ] are cancelled.
Wipe Mode and Mix Mode
If either one of the following operations is carried out,
stored images will be erased, and Wipe and Mix
Functions cannot be used.
OUse the Camera Search Function
OPress the [STILL] Button
44
44
44
$ Adjusting the Microphone Sensitivity
OWhen this setting is changed, the [AUDIO LEVEL]
OWhen [ZOOM MIC] is set to [ON], set the zoom to
] Indication
OSelect a lower setting for [GAIN] or set [MIC
OIt is recommended that you check through the
$ Playing Back
Repeat Playback
If you continue to press the [1] Button for 5 seconds
or longer, the Camera Recorder switches to Repeat
Playback Mode, and the [R!] Indication appears. (To
cancel Repeat Playback Mode, set the [OFF/ON]
Switch to [OFF].)
Listening to Playback Sound through Headphones
If you want to use the headphones to listen to the
playback sound, connect the headphones to the
[PHONES] Socket (-8-) on the Camera Recorder. In
this case, no sound (including a warning sound and
shutter sound) will be reproduced through the built-in
speaker of the Camera Recorder.
Choosing Sound during Playback
You can select the sound by using the [AUDIO OUT]
setting on the [PLAYBACK FUNCTIONS] Sub-Menu.
STEREO: Stereo Sound (main sound and sub sound)
L:
R:
OIf you dub a tape recorded at the [12bit] selected as
$ Index Search Functions
OIndex Search may not be possible at the beginning
OBecause Photoshot Index Signals are not recorded
OScene Index Search may not function properly if the
] and
Level
setting on the [RECORDING SETUP] Sub-Menu of
the [VCR FUNCTIONS] Main-Menu will likewise be
changed.
the [T] position before performing this adjustment.
LEVEL] to [AUTO].
headphones before recording to ensure that the
sound is not distorted.
Left channel sound (main sound)
Right channel sound (sub sound)
the [AUDIO REC] on the [RECORDING SETUP]
Sub-Menu, playback sound becomes stereo sound
regardless of the [AUDIO OUT] setting if [12bit
AUDIO] is set to [MIX].
of tape.
on still pictures recorded in Continuous Photoshot
Mode, the Photoshot Index Search Function cannot
be used for these still pictures.
interval between 2 scene index signals is shorter
than 1 minute.
Hide quick links:
Advertisement
Table of Contents
