Advertisement
Quick Links
Advertisement
Summary of Contents for Haltech HT051100
- Page 1 PLATINUM SPORT GM (HT051100) QUICK START GUIDE...
- Page 2 Proof of purchase, in the form of a bill of sale or receipted invoice, which indicates that the product is within the warranty period, must be presented to obtain warranty service. Lockin Pty Ltd trading as Haltech suggests that the purchaser retain the dealer’s dated bill of sale as evidence of the date of retail purchase.
- Page 3 PLATINUM Sport GM Quick Start Guide Congratulations on purchasing a Haltech Engine Management System. This fully programmable Plug and Play product opens the door to virtually limitless performance modification and tuning of your vehicle. Programmable systems allow you to extract all the performance from your engine by delivering precisely the required amount of fuel and ignition timing that your engine requires for maximum output under all operating conditions.
- Page 4 ECU Installation To install your new Platinum Sport GM to your vehicle, please follow the procedures below. * Please Note the following Installation photos are based on a VQ V8 Statesman You will require the following tools Drill with Sharp 4mm Drill bit ( to remove the security cover if installed) •...
- Page 5 Remove OEM ECU from vehicle. Figure 2 – OEM ECU Removal Connect the Haltech Sport GM to the vehicles wiring harness Connect the USB cable and optional Auxiliary harness (#HT040003 if required) Mount the ECU to the vehicle using 3M Velcro tape and cable ties...
- Page 6 Route the connected USB Cable up to the glove compartment for storage and easy access for programming. Re-fit the kick panel to the vehicle Figure 4 – Haltech Sport GM ECU with kick panel re-installed With the ECU installed do not attempt to start the vehicle. You will need to configure the ECU.
- Page 7 With the engine started and running its now time to tune This is best achieved by your nearest engine tuner See the listing of Haltech dealers on our website to find the one closest to you. www.haltech.com Figure 5 – Haltech ECU Manager Software...
- Page 8 ECU Manager Software ECU Manager software is used for setup, calibration and diagnostics and can be found on the CD supplied with this unit or downloaded from the Haltech website www.haltech.com Minimum System Requirements Operating System: Windows 2000 SP4 / XP / Vista / Windows 7...
- Page 9 Help tab located at the top left of the screen ECU Manager File Extensions When ECU manager saves the map from the Haltech ECU, it saves the map with a Haltech specific file extension. The File extension can be broken down as follows: Example File : xxxx.hsGM-109...
- Page 10 Fit additional sensors. (e.g. MAP,Temperature, Wide-band 02 Sensors) • Control additional devices via relays • Control additional solenoids directly (e.g. Haltech Boost Control solenoid) • The Rear Auxiliary harness is available as an optional extra. ( HT040003 ) Looking into B ack O f C onnector...
-
Page 11: Wire Connections
Digital Pulsed Outputs ( DPO ) Digital Pulsed Outputs are capable of producing pulsed waveforms with varying duty and frequency. DPO's can be used to control various devices such as thermo-fans, shift lights, bypass air control valves, boost control solenoids etc. When a Digital Pulsed output is activated by the ECU the output will switch to ground. - Page 12 Simply connect the device directly to the 8 pin CAN connector on the rear of the ECU or connect using an optional Haltech CAN Hub (order as part # HT059991) if multiple expansion devices are required).
- Page 13 ECU Pinout Figure 9 – Platinum Sport GM Pinout...
- Page 14 Notes...
- Page 16 HALTECH HEAD OFFICE: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com See the Haltech Website for your local authorized dealer. www.haltech.com Version 1...