PIONEER Service Manual. A subscription to, or additional copies Also test with plug reversed of, PIONEER Ser vice Manual may be obtained at a (Using AC adapter Earth nominal charge from PIONEER. plug as required)
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. VSW-1...
1. SPECIFICATIONS Specifications 1. General Power ............VSW-1/KUC : 120 V, 60 Hz Power ..VSW-1/RYL:AC 110-120 V/AC 220-240V, 50/60 Hz Power consumption ........VSW-1/KUC : 8 W Power consumption ........VSW-1/RYL : 9 W Operating temperature ........+5°C to +35°C Storage temperature .........
Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING SECTION VSW-1...
Page 7
See Contrast table (2) NSP 8 Polyethylene Bag AHG7117 (0.06x230x340) Packing Sheet DHX1008 (2) CONTRAST TABLE VSW-1/KUC and VSW-1/RYL are constructed the same except for the following : Mark No. Symbol and Description VSW-1/KUC VSW-1/RYL 1 Instruction Manual (German, French, Not used DRB1375...
2.2 EXTERIOR SECTION RYL type only KUC type only VSW-1...
Page 9
> FU1 Fuse See Contrast table(2) POWER Knob DNK4366 SW Bracket DNH2631 (2) CONTRAST TABLE VSW-1/KUC and VSW-1/RYL are constructed the same except for the following : Mark No. Symbol and Description VSW-1/KUC VSW-1/RYL 4 TRANS Assy DWR1395 DWR1397 >...
Page 13
• The > mark found on some component parts indicates the VOLTAGE SELECTOR importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. • : The power supply is shown with the marked box. DSA1026 VSW-1...
Page 17
7WHU04FU Notes is STBY RS1/16S***J Ω RESISTOR NO MARK RS1/16S****F CKSRYB µ F CAPACITOR NO MARK CERAMIC CCSRCH µ F CCSRCK µ F CEJQ µ F/V NO MARK ELCTROLYTIC CEAL µ F/V NO MARK LCTC H INDUCTOR LCYA H VSW-1...
A-FS2IN A-FS2OUT Switches PANL Assy B-FS1IN S301 : Video A B-FS1OUT S302 : Video B FADER_START_B S303 : Video Auto S305 S304 : Fader Start A DSH1055 S305 : Fader Start B B-FS2IN B-FS2OUT S306 : NTSC / PAL VSW-1...
Page 21
2SC4081(QRS) GNDD 2SC4081(QRS) V+5D Q301 LEDAT DTA124EUA LED-AUTO 2SC4081(QRS) Q317 Q315 Q314 Notes RS1/16S***J Ω 2SC4081(QRS) RESISTOR NO MARK CKSRYB µ F NO MARK CERAMIC 2SC4081(QRS) CCSRCH µ F CAPACITOR GNDD CEJQ µ F NO MARK ELCTROLYTIC is STBY VSW-1...
110-120V / 220-240V P.T. DSA1026 DEK1089 T80mAL250V AKR7001 AC CORD AKR7001 DKP3732 RKP1751-A VDG1061 VTL-004- AC Input DTT1175 CAUTION FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, TRNS ASSY (/RYL : DWR1397) REPLACE WITH SAME TYPE AND RATINGS OF FUSE VSW-1...
Page 23
DSA1029-A BA05T ACG7039-A 0.01 PF03EN-D05 DKP3727- Board in Connector ASSY AC-ON/OFF S3B-EH RB060L-40 RB060L-40 RB060L-40 RB060L-40 ICP-N15 VLED AEK7005 S4B-EH DE012WF0 mark found on some component parts should be replaced with same parts (safety regulation authorized) of identical designation. VSW-1...
V : 0.5V/div. H : 10µsec/div. V : 0.5V/div. H : 10µsec/div. V : 0.5V/div. H : 10µsec/div. IC210-Pin9 IC210-Pin5 IC214-Pin11 V : 0.5V/div. H : 10µsec/div. V : 0.5V/div. H : 10µsec/div. V : 0.5V/div. H : 10µsec/div. VSW-1...
Page 25
V : 0.1V/div. H : 10µsec/div. V : 1.0V/div. H : 50nsec/div. IC205-Pin15 IC151-Pin27 V : 1.0V/div. H : 50nsec/div. V : 1V/div. H : 2nsec/div. IC205-Pin13 IC208-Pin7 V : 1.0V/div. H : 20nsec/div. V : 1V/div. H : 100nsec/div. VSW-1...
4.3 TRNS, PWSB and REG ASSYS SIDE A SIDE A PWSW ASSY TRNS ASSY CN 5 J100 IC 4 IC 3 CN 4 (DNP2127-B) IC 2 REG ASSY POWER DWR1396 TRANS. (DNP2127-B) LIVE AC IN NEUTRAL (DNP2127-B) C D E VSW-1...
Page 33
SIDE B SIDE B PWSW ASSY TRNS ASSY CN 5 J100 IC 4 IC 3 CN 4 (DNP2127-B) IC 2 REG ASSY POWER TRANS. (DNP2127-B) NEUTRAL AC IN LIVE (DNP2127-B) C D E VSW-1...
1 Connect a frequency counter between TP1 (27M) and TP2 (GND). Procedures 2 Adjust VC1 so that the frequency of TP1 becomes 27MHz ± 10Hz. Adjustment Point JACK ASSY SIDE A 27MHz JACK Assy Frequency counter Pull out the hole plug. Adjustment screwdriver (small) VSW-1...
• Switching of video system PAL/NTSC (PLL reset at switching) dance with VSYNC • Delay value setting of chroma sync processing • Setting of chroma sync processing start time (execute after 8m sec. from VSYNC processing) VSW-1...
PWSB Assy and POWER Knob. Remove the PANL Assy. Remove the two screws, and remove the TRN Support, PANL Assy TRANS Assy and Power Transformer. Remove the one screw, and remove the REG Support and REG Assy. ×4 ×3 VSW-1...
Page 40
H-SYNC INPUT or OUTPUT Pull Down to GND PIXCLK 1 / 2 freq. of BCLK for I / O DIGITAL V Pull Down to GND for I / O Pull Down to GND Interlace / Non-Interlace GOSD OSDGREEN DATA INPUT VSW-1...
Page 42
47 P22/A10 SDLYA0 A side Synchronization Out delay setting 1 48 P23/A11 SDLYA1 A side Synchronization Out delay setting 2 49 P24/A12 SDLYA2 A side Synchronization Out delay setting 3 50 P25/A13 SDLYB0 B side Synchronization Out delay setting 1 VSW-1...
Page 43
93 PA0/TP0/TCLKA VSYNC VSYNC input 94 PA1/TP1/TCLKB Connected to GND 95 PA2/TP2/TIOCA0/TCLKC Connected to GND 96 PA3/TP3/TIOCB0/TCLKD Connected to GND 97 PA4/TP4/TIOCA1/A23 Connected to GND 98 PA5/TP5/TIOCB1/A22 Connected to GND 99 PA6/TP6/TIOCA2/A21 Connected to GND 100 PA7/TP7/TIOCB2/A20 Connected to GND VSW-1...
¶ If the VIDEO B button is pressed while holding the VIDEO A but- ton depressed, PLA YER B input is selected; when the VIDEO B button is then released, input returns immediately to PLA YER A, thus allowing quick switching between A/B inputs. VSW-1...
Page 45
Component video input connectors (BNC connectors x 3). Use 3 BNC plug coaxial cables (sold separately) to connect to player Phase comparison is not performed. Use this position when using A’s component video output connectors (Y, C components other than DVJ-X1. VSW-1...
Page 46
• For Mexico, please set to 220 – 240 V before using. Before changing the voltage, disconnect the AC power cord. Use a medium size screw- driver to change the voltage selector switch. 220 – 240V 110 – 120V VOLTAGE SELECTOR VSW-1...