Advertisement
Setting the Time
To set the time press and hold ' ' for two seconds, the time digits will begin
flashing (see Fig. 7). Press the '
ENTER to confirm. The heater will revert to the previous operational mode.
Standby Mode
With the heater ON, if the
button is pressed, the heater will go into standby
mode; the heater switches off, the LCD will display the current set time, only
the mains neon remains illuminated. On pressing the
heater will come on in Manual mode and with a set point setting of 25 ˚C.
Manual Operation
Repeatedly press the ' ' button until the manual mode is visible on the LCD
and confirm the mode selection by pressing ENTER. Use the arrow keys
to select the desired heat setting (see Operational modes for heat setting
details) and confirm the selection by pressing the ENTER key. The desired
temperature can be adjusted at any point during the Manual mode operation,
see Setting the Desired temperature.
Auto mode Operation
Repeatedly press the ' ' button until the Auto mode is visible on the LCD
(see Fig.8) and confirm the mode selection by pressing ENTER. The heater
will operate as per the pre-programmed time and temperature profile (see -
Setting the Timer Profile). Note: if no timer profile has been set it will not be
possible to select 'Auto' mode, it is necessary to set up a time program before
Auto mode can be selected.
During Auto mode operation the LCD display will show the current heat status,
the active programme segment, the time for the next status change, the heat
setting and the set temperature (see Fig.10).
Boost mode Operation
Repeatedly press the ' ' button until the Boost mode is visible on the LCD
(see Fig.9) and confirm the mode selection by pressing ENTER. Once the
boost mode is activated it will be necessary select the boost period, there are
three periods available to choose from, 30 minutes, 1 hour and 2 hours. Use
the arrow keys to select the desired boost period and confirm the selection
using the ENTER key. The default heat setting is ECO mode and the set
temperature is 25˚C. The set temperature can be adjusted if desired, see
Setting the Desired temperature. When the boost mode is active the LCD
display will show the boost mode, timer period selected and the desired set
temperature. The time display will toggle between the current time and time
remaining for the selected boost period.
Frost protection mode
The appliance has a frost protection mode. This setting is useful in areas such
as garages to assist in the prevention of frost damage. In Manual mode, if
the thermostat is set to its minimum setting '5°C', the heater will cycle ON
and OFF to maintain a temperature of approximately 5°C and help protect
against frosty conditions. The frost protection symbol
the LCD display when frost protection mode is activated.
Indicator Neons
Mains On Neon: The mains neon, (see Fig. 1), remains illuminated when
the power is supplied to the product. Note: This does not indicate whether
the heating elements are on.
Heat Neon: Heat neon remains on when the heating element is active. Once
the desired temperature is reached and the element turns off, the heat neon
will indicate this by remaining off.
Bluetooth Neon: The Bluetooth neon will remain illuminated while
successfully paired to another device.
Setting the Desired Temperature
The desired temperature can be set using the '
temperature can be set from 5˚C to 30˚C and this will be shown on the display.
When the temperature is reached the heater will automatically switch OFF. If
the ambient temperature drops the heater will come on again automatically.
Setting the Timer Programmes
There are four program segments available, P1, P2, P3 and P4. For each
segment it is possible to set a desired 'On' time, 'Off' time, Heat mode and
set temperature. It is not necessary to set all four segments if not required.
The default setting is for all segments to be Off. To turn off a pre-programmed
segment it is necessary to set both the 'On' time and the 'Off' time to 00:00.
In order to set up a time/temperature profile the following steps must be
completed:
1. To activate the programming screen press the ' ' key. The program settings
screen for P1 will be displayed and the time will be flashing. This flashing
time is the 'On' time for P1 and can be adjusted using arrow keys. Once the
desired 'On' time has been set press the ENTER key to confirm the time.
2. Select a heat setting using the arrow keys and confirm the selection using
the ENTER key.
3. Set the desired temperature using the arrow keys and confirm the setting
using the ENTER key.
4. The 'Off' time must then be set by using the arrow keys, it is necessary to
then press the ENTER key to confirm the 'Off' time setting.
5. The setup screen will then revert to the P1 'On' time set up screen, at this
point it is possible move to the P2 segment by pressing the ' ' key.
6. If required P2, P3 and P4 segment can be set up using steps 1-4 above.
[c] Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex UK Limited.
' or '
' buttons to set the time and press
button again the
will be displayed on
' or '
' keys. The
7. If it is not required to set up P2, P3 and P4 segment at this stage, continue
to press the ' ' key until the heater reverts to the previous operational mode.
Alternatively if no keys are pressed the programming mode will time out and
revert to the previous operational mode.
Remote Bluetooth Operation
The appliance can be controlled remotely using a smartphone or similar
device. To facilitate this remote operation it is necessary to first download
the Dimplex
app. The app is available on both android and IOS
devices and is available free from the Apple or Android App store. The App is
compatible with Android version 4.3 and above and IOS version 5 and above.
Once the App has been downloaded it is necessary to pair the appliance
with the smartphone to complete the remote setup. Please follow the steps
shown below:
1. Launch the Dimplex
2. To initiate pairing mode on the appliance press and hold the ' ' button for
two seconds. The LCD screen will go blank with the exception of the Bluetooth
logo flashing in the bottom right hand corner, See Fig.11.This indicates that
the device is advertising to be paired with the
3. On the smart phone the appliance should now be visible on the pairing
screen, this will be a unique 6 digit code but will always start with EC, for
example 'ECBC17'. Select this device and press connect to initiate pairing.
4. Once the paring process is complete the app can be used to control the
appliance.
5. Once paired successfully the Bluetooth logo will stop flashing and the
Bluetooth neon will be illuminated.
Safety in use
This appliance incorporates a number of safety devices. In addition to the
'Important Safety Advice' section your attention is drawn to the following;
Tilt Switch
The tilt switch will prevent the heater from working if it is accidentally tipped
over on its side. If the radiator is tipped over while it is hot, disconnect the
power and allow it to cool, then stand the radiator back upright. Reconnect
the power - normal operation should be resumed.
Safety Overheat Protection
For your safety this appliance is fitted with a thermal cut-out. In the event
that the product overheats for some reason, the cut-out prevents excessive
temperatures on the product by cutting the power to the heater. Once the
heater has cooled down, it will reset automatically, it will continue to cycle on
and off automatically until the reason for overheating is removed.
Storage
If the heater is not required for long periods, for example during the summer,
it should be stored in a dry place and preferably covered to prevent the
accumulation of dirt and dust. The supply cord should be neatly
the cable wrap and the plug stored in the cable wrap moulding.
Cleaning
WARNING - ALWAYS DISCONNECT THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of any kind on
the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust
and a damp cloth (not wet) to clean off stains. Be careful not to allow
moisture in to the heater.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not be
disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling
advice in your country.
After Sales Service
Your product is guaranteed for 3 years from the date of purchase The 3 year
guarantee is extended for an additional 2 years when you register the product
with Dimplex, within 28 days of purchase. If you do not register the product with
Dimplex within 28 days, your product will remain guaranteed for 3 years only.
Within the extended warranty period we undertake to repair or exchange this
product free of charge providing:
a) Proof of purchase such as a sales receipt can be provided, showing
that the appliance was bought within the 36-months prior to registering
the defect/fault.
b) The appliance was correctly operated in accordance with the
manufacturer's instructions and used solely for domestic purposes.
c) The defect/fault was not as a result of accident, misuse, unauthorised
modification or inexpert repair
Your rights under this guarantee are additional to your statutory rights, which
in turn are not affected by this guarantee.
Validation of extended warranty
To validate your extended warranty register with us online at http://register.
dimplex.co.uk
N.B. Each qualifying product needs to be registered with Dimplex individually.
Please note that the extended warranty is only available in the UK and
Ireland
app on the smartphone or similar device.
app.
coiled around
Advertisement
