Name Of Each Part; Preparation Before Operation; How To Operate - Panasonic CS-C12CKP Operating Instructions Manual

NAME OF EACH PART

I Remote Control
1
2
AUT AUTO HEA HEAT COOL COOL DR DRY FAN AN
AUTO
ON
AUTO
OFF
FAN
TEMP
3
OFF/ON
!
4
5
#
MODE QUIET POWERFUL
6
AIR SWING $
AUTO MANUAL
FAN SPEED
7 $
1 2 3
8
%
ON SET
9 ^
OFF CANCEL
&
TIMER
0 *
CHECK RESET CLOCK
(
G Remote Control Signal.
• Make sure it is not obstructed.
• Maximum distance : 10 m.
• Signal received sound.
One short beep or one long beep.
G Notes for Remote Control.
• Do not throw or drop.
• Do not get it wet.
• Certain type of fluorescent lamps may affect
signal reception. Consult your dealer.

PREPARATION BEFORE OPERATION

I Indoor Unit
1
2
6
3
5 4
1
Connect the power supply cord to an independent
power supply
2
Open the front panel
3
Remove the air filters
AUTO HEAT COOL DRY FAN
AUTO
4
Fit the air purifying filters in place
5
Insert the air filters
AUTO
FAN
6
Close the front panel
I Remote Control
– To set the current time
AIR SWING
AUTO MANUAL FAN SPEED
1 2 3
ON SET
OFF
CANCEL
2
TIMER
1
CHECK RESET CLOCK
1 Press 1.
2 Then press 2 to increase or decrease the time.
3 Press 1 again.
Set time at display will light up.
CS-C7CKP CU-C7CKP5 / CS-C9CKP CU-C9CKP5 / CS-C9CKP CU-C9CKP6 / CS-C12CKP CU-C12CKP5 / CS-C12CKP CU-C12CKP6
1 Signal Transmitter
2 Operation Display
3 Ionizer Mode Operation Button
4 Room Temperature Setting Button
(illuminating button)
5 Operation Mode Selection Button
6 Quiet Mode Operation Button
7 Auto Airflow Direction Button
8 ON-Timer Button
9 OFF-Timer Button
0 Reset Point
(Press with fine-tipped object to clear the memory)
! OFF/ON Button
(illuminating button)
@ Powerful Mode Operation Button
# Fan Speed Selection Button
$ Manual Airflow Direction Selection Button
% Timer Set Button
^ Timer Cancellation Button
& Time-Setting Button
* Clock Button
( Remote Control Cover

HOW TO OPERATE

2
3
5
I To start the operation
• Press 1.
• POWER indicator (green) on the indoor unit will light
up.
• To stop, press once more.
I Setting Mode
• Press 2 to select:-
Cooling Model
AUTO – Automatic Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
FAN – Air Circulation Operation
Heat Pump Model
AUTO – Automatic Operation
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
33
G How to Insert the Batteries
2
1
Slide down the remote control cover completely
2
Insert the batteries
– Be sure the direction is correct
– 12.00 at display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
G About the batteries
• Can be used for approximately one year.
G Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
I Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 16°C ~ 30°C.
• Recommended temperature:
Cooling Model
COOL –> 26°C ~ 28°C
DRY –> 1°C ~ 2°C
lower than the
1 room temperature
6
• During AUTO Operation, press 3 to select:-
4
• Operation with 2°C higher than the standard
temperature.
• Operation with the standard temperature.
• Operation with 2°C lower than the standard
temperature.
G Standard Temperature
Cooling Model
Indoor
Operation
temperature
Cooling
23°C
Soft Dry
• Once the Automatic Operation is selected, the indoor
temperature sensor operates automatically to select
the desired operation mode with Cooling or Soft Dry.
• After the operation mode has been selected, the
mode does not change.
Heat Pump Model
Indoor
temperature Operation
Cooling
23°C Soft Dry
20°C
Heating
• At the beginning of the automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the indoor temperature.
• The operation mode changes every hour, when
necessary.
1
Heat Pump Model
COOL –> 26°C ~ 28°C
DRY –> 1°C ~ 2°C
lower than the
room temperature
HEAT –> 20°C ~ 24°C
Standard
temperature
25°C
22°C
Standard
temperature
25°C
22°C
21°C