Page 1
ELECTRIC FLAT PANEL FIREPLACE HEATER GL2036CY GL2050CY GL2060CY GL2072CY BG-36B BG-50B BG-60B BG-72B OWNER’S MANUAL 36”/50”/60”/72 Inch Crystal Recessed Wall Mounted Electric Fireplace AC 110-120V 60Hz 1500W Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could WARNING result in fire, electric shock, or serious personal injury.
IMPORTANT SAFETY INFORMATION! WARNING Read all instructions before using this heater! This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
Page 3
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! ALWAYS turn this heater off before unplugging it from the outlet. ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace. ...
Installation and Assembly Your appliance is a wall-mounted, recessed and/or mantel installed appliance. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas. NOTE: Follow all National and local electrical codes. MINIMUM CLEARANCE TO COMBUSTIBLES Measurements are taken from the glass front.
Page 6
( B ) STEP A. Selection a dry wall to open a hole for fireplace box. Size of hole as below chart Figure ( A ) Framing Hole Size Model Number BG-36B 33" (83.82CM) 20.75" (52.71CM) BG-50B 47" (119.38CM) 20.75" (52.71CM) BG-60B 47"...
Page 7
( C ) STEP C. Take off the two screws in both sides of the glass panel. Figure ( C ) STEP D. Have two person to take the glass panel out of the fireplace box. Place it to a soft and clean place.
Wall Mounted Installation Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall. A.Select a location that is not prone to moisture and is located at least 36" (914mm) away from combustible materials such as curtain drapes, furniture, bedding, paper, etc.
Page 9
GL2072CY Wall Bracket Illustrated Pebbles Ember Installation Glass front must be removed and the appliance must be mounted in its final location before the pebble embers are installed. A. CLEAN CRYSTALS MEDIA: crystals media may have a fine oil residue that needs to be cleaned prior to installation. Clean the pebbles with mild dish soap, drain, rinse thoroughly and dry before placing into the tray.
Operation Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death. Power Make sure the ON/OFF switch, located on the left side panel, is in the OFF position. Plug the power cord into a 110~120 Volt 15 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3).
TIMER button: Controls timer settings to 1. Press once. Indicator light turns on. turn off fireplace at selected time. Timer is set to 0.5 hours. Settings range from 0.5 hours to 7.5 hours. 2. Press again until desired setting is TIMER reached.
NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center. Care and Maintenance Cleaning ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace.
Troubleshooting WARNING DISCONNECTED THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. Problem Possible Cause Solution 1. Reset switch by turning main 1. Fireplace turns off 1. Fireplace has overheated and will not turn on.
Page 14
7. Heater does not 1. Thermal switch has been 1. Turn unit off and unplug unit provide heat when tripped. for 10 minutes. Plug back in and turned on. turn unit on. If plug cannot be reached, follow directions for tripped circuit breaker.
Need help?
Do you have a question about the BG-36B and is the answer not in the manual?
Questions and answers