Sony mxp-29 Operation And Maintenance Manual page 26

©
PFL
(pre-
fader
listening)
buttons
When
the
buttons
are
depressed, the pre-fader
signals of
the corresponding channels can be
fed to
the
PHONES
jack
©
.
The
input
signals
can be
monitored with the
channel
faders set to
"0".
To
feed the
pre- fader signals
to
the
monitor speakers,
the
PFL
button
©
for
an
external
speaker system
should also
be
depressed.
0
Channel faders
and
LOCAL
switch
Adjust the signal
level of
each channel going
to
the
line
outputs for
proper balance.
The
position 7 (the
thick
line)
indicates the reference
level.
The
gain
margin
at
the
maximum
setting
is
10
dB.
When
the
LOCAL
switch
is
released,
the input signal
level
can be adjusted by the control signal
connected
to
the
EDITOR connector ®, which controls the
VCA
(voltage
controlled amplifier)
before the channel faders.
When
the
LOCAL
switch
of
any channel
is
depressed,
the
VCA
of
that
channel cannot be controlled
by
the
control signal input to
the
EDITOR
connector.
®
SUB
IN
PAN
controls
Position
the
sound image
from the
SUB
IN
1
or 2
connectors
®
in
the desired place
between
the
LINE
OUT
L
and R
channels.
©
SUB
IN
LEVEL
controls
Adjust
the signal levels
from
SUB
IN
1
or 2
connectors
©
respectively.
The
gain margin
at
the
maximum
setting
is
10dB.
©
SUB
IN
1,
2 connectors (phono
jacks)
Accept
auxiliary input signals
such
as those from an
echo machine.
©
MIC/LINE INPUT
1
through 8 connectors
(XLR-3-31 type)
Accept
line-out signals of
a tape
deck
or
an
amplifier,
or
microphone
signals.
The power can be
supplied to
the
phantom powered
condenser microphones
if
necessary.
(Pin
assignment:
1;
GND,
2; hot, 3; cold)
©
tAt
(ground) terminal
When connected audio
equipment such as a record
player,
which requires
ground connection
to
reduce
hum
or
other undesirable noise,
connect
its
ground
wire
to this terminal.
®
LINE
INPUT 3 through 8
connectors (phono
jacks)
Accept line-out
signals
of
tape
decks and amplifiers
for
channels 3
through
8.
©
PHONO INPUT
1,
2
connectors (phono
jacks)
Accept output signals of
record players
equipped
with
a magnetic-
moving
type cartridges.
©
~
AC
IN
connector
Connect
with the supplied
AC power
cord
to
an
AC
power
source.
©
DC
IN
+12V
connector
Accepts an
external
12V DC power
source,
such
as a
Sony BP-90
battery pack.
The
DC
power
backs up
the
AC
power.
WARNING FOR THE
CUSTOMERS
IN
THE
UNITED
KINGDOM
THIS
APPARATUS MUST
BE
EARTHED
to
your 3-
pin
plug
in
accordance
with following instruction.
IMPORTANT
The wires
in
this
mains
lead are
coloured
in
accordance
with
the
following
code:
Green-and-yellow: Earth (safety earth)
Blue:
Neutral
Brown:
Live
As the colours
of
the wires
in
the
mains
lead of this
apparatus
may
not
correspond
with
the coloured
marking
identifying
the terminals
in
your
plug,
proceed as
follows:
The
wire
which
is
coloured green-and-yellow must
be
connected
to
the terminal
in
the plug
which
is
marked
with the
letter
E
or
by the safety earth
symbol or
coloured green
or
green-and-yellow.
The wire
which
is
coloured blue
must be connected
to
the terminal
which
is
marked
with
the'letter
N
or
coloured
black.
The
wire
which
is
coloured
brown must be connected
to
the terminal which
is
marked
with the
letter
L or
coloured
red.
1-7(E)