Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Avitech Seneca DA-104
Summary of Contents for Avitech Seneca DA-104
- Page 1 User’s Manual Seneca DA-104 / 208 Revision 1.0.0 (May, 2012)
- Page 2 WARNING Do not attempt to disassemble your Seneca DA-104 / 208. Doing so may void your warranty. There are no serviceable parts inside. Please refer all servicing to qualified personnel. TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies.
-
Page 3: Warranty
DAMAGES, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS FOR ANY BREACH OF THIS WARRANTY. If Avitech replaces the defective Product with a replacement Product as provided under the terms of this Warranty, in no event will the term of the warranty on the replacement Product exceed the number of months remaining on the warranty covering the defective Product. -
Page 4: Extended Warranty Options
$200 (US dollars). AVITECH INTERNATIONAL CORPORATION ● 8655 154th Ave NE ● Redmond, WA ● 98052 ● TOLL FREE 1 877 AVITECH PHONE 1 425 885 3863 ● FAX 1 425 885 4726 ● info@avitechvideo.com ● www.avitechvideo.com... -
Page 5: Regulatory Information
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Avitech is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. - Page 6 European Union CE Marking and Compliance Notices Statements of Compliance English This product follows the provisions of the European Directive 1999/5/EC. Dansk (Danish) Dette produkt er i overensstemmelse med det europæiske direktiv 1999/5/EC. Nederlands (Dutch) Dit product is in navolging van de bepalingen van Europees Directief 1999/5/EC.
-
Page 7: Compliance Notice
Australia and New Zealand C-Tick Marking and Compliance Notice Statement of Compliance This product complies with Australia and New Zealand's standards for radio interference. -
Page 8: About This Manual
Preface Welcome Congratulations on purchasing this Avitech Seneca DA-104 / 208 3G / HD / SD-SDI re-clocking distribution amplifier. The new Avitech family of Seneca distribution amplifiers gives you the confidence of absolute compatibility with existing Avitech products while providing the capability of integration within a larger installation. Seneca distribution amplifiers are a simple, robust and cost-effective way of organizing and working with multiple video formats. -
Page 9: Getting Started
Getting Started The Seneca DA-104 / 208 is a miniature, low-cost 1 × 4 / 2 × 8 3G, HD, and SD-SDI re-clocking distribution amplifier. Featuring four / eight separately buffered SDI outputs, the Seneca DA-104 / 208 provides automatic input detection, re-clocking and cable equalization. -
Page 10: Product Features
Magnetic Foot Stand with Screws (4 pieces) A.2 Product Features SD-SDI / HD / 3G distribution Four / eight separately buffered outputs Small form factor 100 meter 3G cable equalization (1694a coax) 3G, HD, or SD-SDI input, auto-sensing ... -
Page 11: Specifications
Specifications Parts Specifications Input 1 or 2 3G, HD, SD-SDI (SMPTE 259 / 292 / 296 / 424) × BNC (Seneca DA-104), or × BNC (Seneca DA-208) Format 3 GB, 1.5 GB, 270 MB automatic select Output 3G, HD, SD-SDI ×... -
Page 12: Block Diagram
Glows amber when no signal is present in the INPUT 2 connector (Standby state). (upper) Glows green when signal is present in INPUT 2 connector. NOTE: Device indicator 2 will not glow for Seneca DA-104 model. Dip switches Sets the video routing configuration. - Page 13 INPUT 1 / 2 BNC connector for 3G / HD / SD-SDI video input sources. NOTE: BNC connector 2 is not available for Seneca DA-104 model. Power connector Connects to the power adapter. A.6 Input / Output Connectors (Rear Panel)
-
Page 14: Application Diagram
Use the following dip switch settings to effect the following video routing configuration – IMPORTANT: Step 3 is not applicable for Seneca DA-104. Setting the pin-2 dip switch to while pin-1 dip switch is would cause no video output. ON (... - Page 15 For automatic video routing, both pin 1 and pin 2 must be in the default position (OFF, OFF). Possible scenarios: If only INPUT 1 port has input signal, then its signal will output to OUTPUT 1-1, 1-2, 1-3, 1-4 ports only. If only INPUT 2 port has input signal, then its signal will output to OUTPUT 2-1, 2-2, 2-3, 2-4 ports only.
Need help?
Do you have a question about the Seneca DA-104 and is the answer not in the manual?
Questions and answers