Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DW SitePro SLR202GR
Summary of Contents for DW SitePro SLR202GR
- Page 1 Operating / Safety Instructions Consignes de fonctionnement / sécurité Instrucciones de funcionamiento y seguridad IMPORTANT: IMPORTANT IMPORTANTE: Read Before Using Lire avant usage Leer antes de usar model SLR202GR www.SitePro.us.com Toll Free: (855) 354-9881...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES Working safely with this instrument is possible only when the operating and safety infor- mation are read completely and the instructions contained therein are strictly followed. The use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure. - Page 3 Fig. A www.SitePro.us.com...
-
Page 4: Technical Data
FEATURES (Fig. A) Light House Charging Port Rotating Head Instrument Base and Battery Pack Glass Enclosed Laser Plumb Beam Heavy-Duty Handle Laser Down Plumb Beam Control Keypad TECHNICAL DATA SLR202GR Leveling Accuracy 1/8-in at 100-ft (3mm at 30m) Range with Detector (Diameter) 1600-ft (500m) Interior Range (Diameter) 320-ft (98m) - Page 5 CONTROL KEYPAD ICONS Power ON/OFF: Allow laser instrument to self-leveling. Use also to activate the plumb up and plumb down beam. WINDY Power Scanning Beam Variable Smart Single Dual Manual Mode Positioning Speed H.I. Slope Slope Mode Manual/Automatic: While instrument is ON, press and hold once, to activate Manual Mode.
- Page 6 PREPARATIONS Battery Installment Rechargeable and alkaline battery packs are suitable for use to power your instrument. To install/remove batteries: Un-screw the bolt at the bottom of instrument base. Remove the battery pack. Use either alkaline battery or Ni-Mh battery pack. When inserting alkaline batties, pay attention to the correct polarity according to the representation on the inside of the battery compartment.
- Page 7 OPERATIONS Set-up Place the laser instrument on a flat, level survace such as a tripod Setup the instrument in an area where it can not be obstructed and is set at a convenient height. IMPORTANT. Be sure the surface is level with +/- 5° of the laser self-leveling range. Power Press the Power ON/OFF keypad and allow the laser instrument to self-level.
- Page 8 Scanning or Sweeping WINDY Power Scanning Beam Variable Smart Single Dual Manual The Scanning Mode creates a shorter, brighter laser “chalk line” that can be used for Mode Positioning Speed H.I. Slope Slope Mode leveling or plumbing. This feature can also be used to keep the instrument from interfer- ing with other lasers and detectors on site.
- Page 9 First, the X% value on the display will begin to flash. Press the button to enter the Y-axis slope/grade menu. The Y% value on the display will begin to flash. WINDY Scanning Beam Variable Smart Single Dual Manual Mode Positioning Speed H.I.
-
Page 10: Accuracy Check
Vertical Laydown Positioning Place the laser instrument in the laydown position on a flat, level surface. Press the Power ON/OFF button. Allow WINDY the instrument to self-level. Power Scanning Beam Variable Smart Single Dual Manual Mode Positioning Speed H.I. Slope Slope Mode ACCURACY CHECK... - Page 11 Allow the laser instrument to self level and begin rotating. Mark the beam position on the 165 ft wall or scale plate as H1. (50m) Loosen the screw of the tripod, and then turn the laser 180°. Allow the unit to level and rotate, mark the beam position on the wall or scale plate as H2.
- Page 12 Rotate the instrument horizontally 180° (without changing the height). After laser instrument levels, direct the laser beam onto Wall B. Mark the center point z of the laser beam on the opposite wall B. 1.5 ft 1.5 ft Approx. 100 ft (0.5m) (0.5m) (30m)
-
Page 13: Remote Control
REMOTE CONTROL The remote control can be used up to a maximum of 65 feet (20 m) away from the instrument. Setup the instrument and power on (remote does not power on instrument). The remote control communicates with the laser instrument in real-time. The remote must be pointed towards the instrument for proper operation. -
Page 14: Maintenance
The detector has 3 control buttons: ON/OFF Button Audio Button with 3 settings: OFF – LOW – HIGH Sensitivity Button This will either give a narrow or a broader range of detection. When the detector is too high a slower beep will be emitted, when too low, a fast beep will be emitted, when same level as beam a continuous pitch will sound- at this point the centre of the detector is at... -
Page 15: Warranty
WARRANTY Limited Warranty Program SitePro warrants the SLR200 Series Rotary Lasers to the original purchaser for a period of two (2) years from date of purchase against any defects in material or workmanship. This warranty does not cover part failure due to normal wear or tool abuse. For more details of warranty coverage and warranty repair information, call (855) 354-9881. - Page 16 © Dave White’s SitePro, LLC Otterbein, IN www.sitepro.us.com UM-27SLR202 r.1 5/15 Printed in China...
Need help?
Do you have a question about the SitePro SLR202GR and is the answer not in the manual?
Questions and answers