Huviron SK-RN16 Quick Manual

NVR Quick Guide
Model No.SK-RN08, SK-RN16
Thank you for purchasing our product. If there is any
question or request, please do not hesitate to contact
dealer. This manual is applicable to SK-RN08, SK-
RN16.

Chapter 1. Hard Disk Installation

Before you start
:
Before installing a hard disk drive (HDD), please make sure the
power is disconnected from the DVR. A factory recommended
HDD should be used for this installation.
Tools Required: Screwdriver.
To install a HDD on your DVR:
1) Remove the cover from the DVR by unfastening the screws on
the back and side.
2) Connect the HDD to the motherboard of the DVR with the
included data cable.
- 1 -
2) Click the Shutdown button to enter the following dialog box:
3) Click the Yes button. The following message box pops
up:
4) Turn off the power switch on the rear panel of DVR.
- 5 -
3) Connect the power cable to the HDD
4) Re-install the cover of the DVR and fasten screws.

Chapter 2. Rear Panel

Rear Panel of SK-RN16
- 2 -

Chapter 5. Using the Setup Wizard

The Setup Wizard can walk you through some important settings
of the device. By default, the Setup Wizard starts once the
device has loaded.
Operating the Setup Wizard:
1) The Setup Wizard can walk you through some important settings
of the NVR. If you don't want to use the Setup Wizard at that
moment, Time by leaving the "Start wizard when NVR starts?"
checkbox checked.
2) Click Next button on the Wizard window to enter the Login window.
3) Enter the admin password. By default, the password is 12345.
4) To change the admin password, check the New Admin Pass
word checkbox. Enter the new password and confirm the
password in the given fields.
5) Click the Next button to enter the date and time settings window.
- 6 -
No. Item Description
1 VIDEO OUT BNC connector for video output.
AUDIO OUT
2 BNC connector for audio output.
3 AUDIO IN BNC connector for audio input. (Also for voice talk)
4 RS-232 Interface Connector for RS-232 devices.
DB9 connector for VGA output. Display local video
5 VGA
Output and menu.
6 HDMI HDMI video output connector.
7 USB Port Connects USB disks and devices.
8 LAN Interface Connector for LAN (Local Area Network).
Connector for RS-485 device. T+and T-pins conncet to
RS-485 Interface
R-pins of PTZ receiver respectively.
9
ALARM IN Connector for alarm input.
Connector for alarm output.
ALARM OUT
10 Power Supply 12VDC power supply.
11 Power Switch Switch for turning on/off the device
12 GROUND 12VDC power supply.

Chapter 3. RS-485 Connections

To connect RS-485 devices (e.g., pan/tilt unit) to the DVR:
Press and hold the orange part of the pluggable block; insert signal
cables into slots and release the orange part. Ensure signal cables
are in tight.
Note: Make sure the pan/tilt receiver unit is connected to the
D+ and D- of the RS-485 terminal of DVR.
- 3 -
6) After the time settings, click Next button which takes you back to the
Network Setup window.
7) Click Next button after you configured the network parameters,
which takes you to the HDD Management window.
8) initialize the HDD, click the Init button. Initialization removes all the
the data saved in the HDD.
9) Click Next button. You enter the Adding IP Camera interface.
10) Click Search to find online IP Camera. Select the IP Camera to
be added, and click the Add button.
- 7 -

Chapter 4. Startup and Shutdown

Proper startup and shutdown procedures are crucial to expand
ing the life of the DVR.
Before you start:
Check that the voltage of the extra power supply is the same
with the device's requirement, and the ground connection is
working properly.
Starting up the device:
Steps:
1) Check the power supply is plugged into an electrical outlet. It is
HIGHLY recommended that an Uninterruptible Power Supply (UPS)
be used in conjunction with the device.
2) Press the POWER button on the rear panel. The Power indicator
LED should turn green indicating that the unit begins to start up.
Shutting down the device:
Steps:
1) Enter the Shutdown menu.
Menu > Shutdown
- 4 -
11) Click Next button. Configure the recording for the searched IP Camera.
12) Click Copy to Copy the settings to other channels.
13) Click OK to complete the startup Wizard.
- 8 -