Important Safety Information Improper handling can cause serious damage to the EdgeStar beverage cooler and/or injury to the user. This beverage cooler is designed for domestic indoor use only. Any other use may invalidate the warranty. Please review the rating label located on the lower left side of the inner cabinet of the unit for electrical and other technical data related to this unit.
Vent the room in which the appliance is located for several minutes. Contact the EdgeStar Customer Service Department for advice. The more coolant there is in an appliance, the larger the room it should be installed in. In the event of a leak, if the appliance is in a small room, there is the danger of combustible gases building up.
Table of Contents IMPORTANT SAFETY INFORMATION ..............I IMPORTANT SAFETY INFORMATION (CONTINUED) ........II INTRODUCTION ....................1 PARTS IDENTIFICATION ..................2 ......................2 RONT INSTALLING THE BEVERAGE COOLER ............3 ..................3 YPES OF NSTALLATION Freestanding installation: ................3 Built-in installation: ..................3 ................
Introduction Thank you for purchasing this EdgeStar beverage cooler. We are glad you chose us. We believe that your purchase of this product opens a relationship between you and EdgeStar. We will provide the customer support needed to nurture that relationship.
Parts Identification Front View Tip: Gather the model and serial number from the product label and write them down before installing the beverage cooler. EdgeStar Beverage Cooler...
Installing the Beverage Cooler The beverage cooler should be installed in accordance with local electrical code requirements. The beverage cooler should also be placed in a location that is strong enough to support its total weight, keeping in mind that it will weigh substantially more when fully loaded than when empty.
Page 8
See the “Leveling the Beverage Cooler” section. • A standard electrical supply (115 VAC only, 60 Hz), properly grounded in accordance with National Electrical Code and local codes and ordinances is required. EdgeStar Beverage Cooler...
Electrical Requirements ELECTRIC SHOCK HAZARD! Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug. Never use an adapter to bypass the grounding prong. DO NOT use an extension cord. Failure to follow these instructions can result in fire, electrical shock, or death.
3. Pull the shelf forward until the notch aligns with the plastic post on each side of the shelf track. 4. Lift the shelf until both notches pass through the posts. 5. Continue to pull the shelf forward until it is completely removed from the inner compartment. EdgeStar Beverage Cooler...
Installing the Handle IMPORTANT: Do not over tighten the screws and do not use power tools to install the handle. Place the handle over the fixing pin(s) of the door. Using the supplied Allen wrench, tighten the grub screw(s) to secure the handle.
Note: It is normal to see the set temperature and current temperature displays being a few degrees off from each other. If, however, the current temperature deviates more than 9°F from the set temperature, the display will continue to flash. EdgeStar Beverage Cooler...
Page 13
Advanced Functions Allow at least 24 hours before storing your This unit is equipped with a temperature alarm. The alarm will sound and beverages to allow the the temperature display will flash under the following conditions: temperature to acclimate. - The door has been left open for more than 60 seconds. - There has been a lengthy interruption to the power supply.
CLEANING AND MAINTENANCE Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. Exterior Cleaning The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such as 2 tablespoons of baking soda to 1 quart of water.
The door gasket is dirty. Clean the door gasket. The door will not shut properly. The door gasket is not Make sure the door gasket is properly installed. installed correctly. The shelves are incorrectly Correctly install the shelves. installed. EdgeStar Beverage Cooler...
Issue Possible cause Solution E1 or E2 indicate that the air temperature sensor has Contact an EdgeStar customer service agent. Display shows E1, E2 or failed. E7 indicates that the door Contact an EdgeStar customer service agent. switch has failed.
(Height x Width x Depth ) Weight 141 pounds Note: Technical data and performance information is provided for reference only. Specifications are subject to change. Check the rating label on the beverage cooler for the most accurate information. EdgeStar Beverage Cooler...
Page 19
Once an EdgeStar authorized representative has confirmed that your product is defective and eligible for warranty service, the product must be returned to an EdgeStar authorized repair facility. EdgeStar is not responsible for damage resulting from shipper mishandling or improper packaging. Do not return a defective product to the place of purchase.
Need help?
Do you have a question about the VBR440 and is the answer not in the manual?
Questions and answers