Description Of The Accessories; Description Of The Milk Container; Before Use; Checking The Appliance - DeLonghi ECAM23.460 Instructions For Use Manual

3.3 Description of the accessories

(page 2 - C )
C1. Indicator paper
C2. Pre-ground coffee measure
C3. Descaler
C4. Water softener filter (certain models only)
C5. Cleaning brush
C6. Hot water spout

3.4 Description of the milk container

(page 2 - D )
D1. Froth adjustment and CLEAN dial
D2. Milk container lid
D3. Milk container
D4. Milk intake tube
D5. Frothed milk spout (adjustable)

4. BEFORE USE

4.1 Checking the appliance

After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De'Longhi
Customer Services.

4.2 Installing the appliance

Important!
When you install the appliance, you should respect the follow-
ing safety warnings:
-
• The appliance gives off heat. After positioning the appli-
d
ance on the worktop, leave a space of at least 3 cm be-
tween the surfaces of the appliance and the side and rear
walls and at least 15 cm above the coffee maker.
• Water penetrating the coffee maker could cause damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the tempera-
ture could drop below freezing point.
• Arrange the cord in such a way that it cannot be damaged
s
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
s
t

4.3 Connecting the appliance

Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.

4.4 Setting up the appliance

Please note:
• Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
You should customise water hardness as soon as possible
following the instructions in section "14. Setting water
hardness".
1. Connect the appliance to the mains electricity supply (fig.
1). Make sure the main switch (A8) at the back of the appli-
ance is pressed (fig. 2);
2. Remove the water tank (A9), fill to the MAX line with fresh
water (fig. 3A) then put back in the appliance (fig. 3B);
You must first choose the language by turning the selection dial,
or waiting until the languages scroll through on the display (B1)
automatically at intervals of about 3 seconds:
3. When "English" appears on the display, press the
button (B9) (fig. 4) for a few seconds until "English set" is
displayed;
Follow the instructions indicated on the appliance display:
4. "INSERT WATER SPOUT": Check that the hot water spout
(C6) is inserted on the connection nozzle (A12) and place a
container holding a minimum of 3,38 fl. oz. (100ml) under-
neath (fig. 5);
5. "HOT WATER Confirm?" appears on the display;
6. Press the button to confirm (fig. 4). The appliance
delivers water from the spout then goes off automatically.
The coffee machine is now ready for normal use.
Please note:
• The first time you use the coffee maker, you need to make
4/5 cups of coffee or 4/5 cappuccinos before it starts to give
satisfactory results.
• When making the first 5-6 cappuccinos, it is normal to hear
the noise of boiling water. After this, the noise becomes
less.
9