Jet AFS-500 Operating Instructions Manual page 2

The machine is designed to operate in
closed rooms and can be placed on a
stable and levelled surface.
Make sure that the power cord does
not impede work and cause people to
trip.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Never leave a running machine
unattended. Before you leave the
workplace switch off the unit.
Keep children and visitors a safe
distance from the work area.
Do not operate the electric tool near
inflamm able liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the air cleaner in a dump
environment and do not expose it to
rain.
Never duct a machine directly into the
air cleaner.
Do not use this equipment to filter
volatile fumes or smoke.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
The air filtration system will support,
but cannot subsidise the application of
a suitable dust extraction device for
your woodworking machines.
Do not stand on the air cleaner.
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn power cord
replaced immediately.
3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards
may still exist.
Woodworking dust can be a health
hazard. The air filtration system will
support but cannot subsidise the
application of a suitable dust
extraction device for your
woodworking machines
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
4. Machine specifications
4.1 Technical data
Air volume flow 6, 8, 10 m³/min
Replacement outer filter
Replacement inner filter
Overall (LxWxH) 400x610x310mm
Net weight
Mains 230V ~1/N/PE 50Hz
Output power 0,12kW (0,16HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
4.2 Noise emission
Acoustic pressure level (EN 11202):
low speed
medium speed
high speed
4.3 Content of delivery
Electrostatic outer filter( 5 Micron)
Inner filter ( 1 Micron)
8 foam pads
Operating manual
Spare parts list.
5. Assembly and start up
5.1 Assembly
If you notice transport damage while
unpacking, notify your supplier
immediately. Do not operate the unit!
Remove all packing from the inside of
the unit by removing the outer filter
and the inner filters.
Dispose of the packing in an
environmentally friendly manner.
5.2 Installation
This unit will work best if it is located
away from corners, and
heating/cooling vents.
This unit is specifically designed to
circulate air and filter dust, which is
generated throughout the work area.
The air cleaner is designed to operate
in closed rooms and can be operated
horizontally and vertically.
Before you set the unit on a stable and
levelled surface, stick four foam pads
(A, Fig 1) to the bottom corners of the
cabinet.
4
5 micron
1 micron
15 kg
0.3 A
There are four extra pads for
mounting on the side for use in the
10A
vertical position.
The handle (B, Fig 1) can be moved
from the top of the unit to the side (C)
if desired.
57 dB (A)
59 dB (A)
5.3 Mains connection
61 dB (A)
Mains connection and any extension
cords used must comply with
applicable regulations.
The mains voltage must comply with
the information on the machine
licence plate.
The mains connection must have a
10 A surge-proof fuse.
Only use power cords marked
H07RN-F
Connections and repairs to the
electrical equipment may only be
carried out by qualified electricians.
6. Machine operation
The buttons I, II, III on the back of the
machine control the air volume flow.
You can choose between low, medium
and high.
The button 0 turns the unti off.
7. Maintenance and inspection
General notes:
Maintenance, cleaning and repair
work may only be carried out after
the machine is protected against
accidental starting by pulling the
mains plug.
Fig 1