Advertisement
PA2X10 & PA2X10BT Specifications
Output Power 1%
1 x 50W
CH 1-4
Accepted Inputs
Aux
Frequency Response
20Hz-20kHz
-46dB
Hum & Noise
-37dB
+49dB
System Gain/Speaker Output
+35dB
(measurement made at 1kHz)
+25dB
Channel EQ (high, low)
SYNC (IN and OUT)
Subwoofer Out
Line Out
Phantom Power
+15 V
USA /Canada
Europe
Power Requirements
UK
Australia
Japan
Speakers
Two 10"
Horn
5 3/4" piezo horn
Power Capacity
50W
60Hz-20kHz
Frequency Response
150Hz-20kHz
Nominal Impedance
8 ohms
Bluetooth Module Features
PA2X10 & PA2X10BT
cm / kg
Dimensions & Weight
Inches / Pounds
PA2X10EX
cm / kg
Dimensions & Weight
Inches / Pounds
1 x 8 ohm load
Mic XLR Balanced, Line Level 1/4" Unbalanced
1/8" Line Level or Bluetooth Device (BT models)
Actual Response is tailored to speaker cabinet for accurate
acoustical response
Residual Noise, all level controls 0% (minimum)
Nominal System Noise, all level controls at 50%
Mic to Speaker Output (CH1 - CH4)
Line to Speaker Output (CH1 - CH4)
Aux to Speaker Output
Treble-10kHz, Bass-100Hz
Both Jacks accept a balanced input and send a pre-master
volume output mix of channels. Recommended use: Linking
two PA2X10 or PA2X10BT units.
20Hz-150Hz
Mic Inputs (CH 1-4)
120VAC/60Hz, 100W nominal/160W with ext cabinet
230VAC/50Hz, 100W nominal/160W with ext cabinet
230VAC/50Hz, 100W nominal/160W with ext cabinet
240VAC/50Hz, 100W nominal/160W with ext cabinet
100VAC/50-60Hz, 100W nominal/160W with ext cabinet
50W 8 ohm each
RMS 100W with extension cabinet
Full Range (subwoofer jack not used)
Crossover Active (1/4" mono plug in subwoofer jack)
4 ohms with extension cabinet
Bluetooth 3.0+EDR compliant. Typical +2dBm Class 2 output
power. Audio DAC:94dB SNR. A2DP profile support
47.4 H x 31 W x 29.0 D /13.1kg
18.66" H x 12.2" W x 11.77" D / 28.9 lbs
47.4 H x 31 W x 29.0 D /13.1kg
18.66" H x 12.2" W x 11.77" D / 22 lbs
PA2X12 & PA2X12BT Specifications
1 x 50W
Output Power 1%
CH 1-4
Aux
Frequency Response
20Hz-20kHz
Hum & Noise
-46dB
-37dB
+49dB
System Gain/Speaker Output
+35dB
(measurement made at 1kHz)
+25dB
Channel EQ (high, low)
SYNC (IN and OUT)
Subwoofer Out
Line Out
Phantom Power
+15 V
USA /Canada
Europe
Power Requirements
UK
Australia
Japan
Speakers
Two 12"
Horn
5 3/4" piezo horn
Power Capacity
50W
60Hz-20kHz
Frequency Response
150Hz-20kHz
Nominal Impedance
8 ohms
Bluetooth Module Features
PA2X12 & PA2X12BT
cm/kg
Dimensions & Weight
Inches/Pounds
PA2X12EX
cm/kg
Dimensions & Weight
Inches/Pounds
1 x 8 ohm load
Mic XLR Balanced, Line Level 1/4" Unbalanced
1/8" Line Level or Bluetooth Device (BT models)
Actual Response is tailored to speaker cabinet for accurate
acoustical response
Residual Noise, all level controls 0% (minimum)
Nominal System Noise, all level controls at 50%
Mic to Speaker Output (CH1 - CH4)
Line to Speaker Output (CH1 - CH4)
Aux to Speaker Output
Treble-10kHz, Bass-100Hz
Both Jacks accept a balanced input and send a pre-master
volume output mix of channels. Recommended use: Linking
two PA2X12 or PA2X12BT units.
20Hz-150Hz
Mic Inputs (CH 1-4)
120VAC/60Hz, 100W nominal/160W with ext cabinet
230VAC/50Hz, 100W nominal/160W with ext cabinet
230VAC/50Hz, 100W nominal/160W with ext cabinet
240VAC/50Hz, 100W nominal/160W with ext cabinet
100VAC/50-60Hz, 100W nominal/160W with ext cabinet
50W 8 ohm each
RMS 100W with extension cabinet
Full Range (subwoofer jack not used)
Crossover Active (1/4" mono plug in subwoofer jack)
4 ohms with extension cabinet
Bluetooth 3.0+EDR compliant. Typical +2dBm Class 2 output
power. Audio DAC:94dB SNR. A2DP profile support
54.9 H x 39.1 W x 39.5 D / 18.7kg
21.61" H x 15.39" W x 15.55" D / 41.2lbs
54.9 H x 39.1 W x 39.5 D / 18.7kg
21.61" H x 15.39" W x 15.55" D / 33.3 lbs
Advertisement
