Related Manuals for Zycoo CooVox U100 Series
Summary of Contents for Zycoo CooVox U100 Series
- Page 1 IP PHONE SYSTEM CooVox Series-U100 For Small and Medium Business Quick Installation Guide Quick Installation Guide PWR SYS SLOT2 SLOT1 CooVo x IP Phone System www.zycoo.com...
-
Page 2: Table Of Contents
Table of Contents 1 Package Contents 2 Hardware Installation 2.1 Safety Precautions 2.2 Installation Tools 2.3 Product Installation 2.4 Physical Connection 2.5 LED Definitions 3 Basic System Configuration 3.1 Web Login 3.2 Network Configuration 3.3 Choose the Module 3.4 Reset to factory 4 Further Configuration... -
Page 3: Package Contents
1 Package Contents Thank you for purchasing ZYCOO IP Phone System. These are the items included with your IP Phone System purchase: Power Cord IP PBX Antenna(only for Quick Installation GSM Module) Guide Two mounting brackets Warranty Card and fittings... -
Page 4: Hardware Installation
2 Hardware Installation The followings are instructions for setting up ZYCOO CooVox-U100 IP PBX. Please refer to the illustration and follow the simple steps below to quickly install your IP phone system. 2.1 Safety Precautions Notes: To avoid any device damage and bodily injury caused by improper use, please observe the following rules. - Page 5 To ensure normal operation and long service life of the device, please install it in an environment that meets the requirements described in the following subsection. Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, m e c h a n i c a l p ro p e r t y c h a n g e s a n d c o r ro s i o n s .
- Page 6 Electromagnetic Interference SLOT2 SLOT1 CooVox IP Phone System Electronic elements including capacitance and inductance on the device can be affected by external interferences, such as conducted emission by capacitance coupling, inductance coupling, and impedance coupling. To decrease the interferences, please make sure to take the following measures: Use the power supply that can effectively filter interference from the power grid.
-
Page 7: Installation Tools
Ensure the rack and devices are well earthed. Make sure the power socket has a good contact with the ground. Keep a reasonable cabling system and avoid induced lightning. Use the signal SPD (Surge Protective Device) when wiring outdoor. Note: the device is specially designed for the usage of communication operators’... - Page 8 3.Please ensure the direction of the module is correct (ZYCOO-logo side up). 4.Push the module into the module slot through the guide rail. 5.Tighten the locking screws on the both ends of the module. Notes: Do not touch any device on the module, just to prevent the module from being damaged by static electricity.
- Page 9 PW R SY S W A N LA N SL O T2 SL O T1 C o o V o IP P h o n e S y s te m 4.After the brackets are attached to the device, use suitable screws (not provided) to secure the brackets to the rack, as illustrated in the following figure.
- Page 10 If CooVox-U100 IP PBX is installed in the computer room, and the room has dedicated Grounding bar, then the using of ground wire to connect the device with the Grounding bar is put to the first consideration as shown in the following figure. AUDIO [1] IP PBX(Rear panel) [2] Grounding Terminal...
-
Page 11: Physical Connection
2.4 Physical Connection CooVox-U100 Computer Power Router PSTN 2.5 LED Definitions Indication Function Status Explaination Power On Power Status Power Off Blink System Works System Status System Fails Blink Data Transport Data Status No Data Transport Channel Loading Success Green Channel Ringing Blink Channel Loading Failure... -
Page 12: Basic System Configuration
3 Basic System Configuration 3.1 Web Login Step 1. Connect a computer and the CooVox device in the same network. IP address is usually in the 192.168.10.X segment. Step 2. Start a web browser. To use the user interface, you need a PC with Internet Explorer (version 7.0 or higher), Firefox, Chrome. -
Page 13: Network Configuration
3.2 Network Configuration Step 1. Go to Network Settings Network Step 2. Configure the network information There are three types of network connection. They are Static, DHCP, PPPoE(Point-to-Point Protocol over Ethernet). You can find detail settings in the user manual. -
Page 14: Choose The Module
3.3 Choose the Module Go to System Module Settings When using the module except FXO/FXS/GSM, you need to set the module parameters with the below page. Module Type: Select the module type of the device slot. FXS/FXO/GSM module Default type. You don’t need set anything for these modules. -
Page 15: Reset To Factory
You can also browse our online FAQ resource at ZYCOO website first to check if it could solve your issue. If you need more support, please contact ZYCOO support team.