Yamaha TX 802 Owner's Manual page 9

VOICE SELECT
VOICE
SELECT
This
is
where you
select
voices
to
use
in
a
Performance memory. The
TX802
has 3
banks,
each
with
64
voice
memories; banks
A
and B
are
ROM
preset voices and bank
I
is
for voices
you
create or
edit.
A
cartridge
{bank
C)
can
contain
an
additional
64
voice memories.
As
you
move
the cursor, the
upper
line
of the
LCD
will
show
the
name
of
each
voice
in
the Performance.
If
the voice
was
created using Micro Tuning
(p.16)
or
Fractional Scaling
(p.
20),
a "t" or "f"
will
be
dis-
played
to
the
left
of the voice
name.
If
a
cartridge
Micro Tuning
was
used
but
a
Micro Tuning data
cartridge
is
not
inserted,
the "t"
will
blink,
and
Equal
Temperament
will
be used
instead.
If
a Fractional Scaling data
cartridge
is
not
inserted, the "f"
will blink.
The "Rch"
indicates the
MIDI channel
that
this
voice
is
receiving. (Specified for
each
tone generator
in
Performance
Edit.)
Fractional Scaling
Micro Tuning
Voice
Name
MIDI Receive Channel
VOICE SELECT
105 A64 B42
(t)(f)<GrandPiano> Rch=
1
A39
A31 112
B44
B23
Select Voices
Press
+/-1
to select a voice
where
the cursor
is
blinking.
Or you can
use the
ten-key
pad
to
enter
a
number 1-64 and
then press ENTER.
To
select voice
memory
banks
{Internal,
Cartridge, A,
B)
hold
ENTER
and
press INT/CRT.
A
list
of the factory preset voices (banks
A
and
B)
is
given
on
p.
27.
Linked Tone
Generators
Tone
generators
can be
linked
together
to
form
an instrument
that
can
play
4-
1
6 simultaneous
notes. Pressing
ENTER + OFF
will
switch
a
voice
off.
A
long
arrow "«_"
will
be
shown
in
place of the voice
number, and
the tone generator
to
the
left will
be given
two
extra notes.
In
this
way, you can use
a
single
instrument
to play
chords
of
up
to
16
notes. For
example
in
the
LCD
below,
the
TX802
is
acting as
3 separate
instruments; with 8-note, 6-note and
2-
note polyphony.
To
switch the voice
on
again,
press
ENTER +
ON.
2x1=2
notes
2x4
= 8
notes
2x3
=
6 notes
Tone Generator
On/Off
Just as
in
PERFORMANCE
SELECT
mode, you
can
"turn off"
the MIDI
input
to
a
tone generator by
pressing
TONE GENERATOR
ON/OFF
1-8.
Tone
genera-
tors that are linked or
in
alternate
assign
mode
(p.
15)
will turn
on
or off
together.
Store Voice
While
in
VOICE SELECT
mode, you
can
store the currently selected voice
to
an
internal or cartridge
memory.
Press
STORE
and use
the ten-keys
and INT/CRT
to specify the destination
INT
1-64
or
CRT
1-64. Press
ENTER,
then
YES.
If
you
are
sure,
press
YES
again.
{If
the voice uses
Fractional Scaling, an
appropriately
formatted
cartridge
must
be
inserted.
When
you
store the voice
to
INT
memory,
the
Fractional
Scaling data
will
be
stored to
the corresponding
location
in
the
cartridge.)
-7-