Introduction Thanks for purchasing 9908 UHF Radio. Please read this manual carefully to learn its functions and operations before using. With elegant design, stable performance, and easy-to-use feature, transceiver 9908 is developed for widely using. It offers you a normal communication when you are in the rural area, forest zone, pasturing area or sea area. The fine appearance of 9908 meets your needs of personality.
Table of Spare Parts Spare Parts Unit quantity Antenna Belt Clip Li-ion Battery Pack Adapter Charger Qualified Card User manual Handstrap...
Page 4
Features 1.Frequency:430MHz-470MHz 15.TX/RX CTCSS/CDCSS adjustable 2.Easy Operation by OLED display 16.STEP5/6.25/10/12.5/20/25/50/100K 3. 7.4V 1800mAh Li-ion battery 17.Scanning :VFO/Channel 4.DPMR digital and analog communication 18.SQL(0-9) 5.Analog Wide/Narrow:25K/12.5K 19.Backlight On/Off 6.High/Low Power : 4w/1w 20.Power SAVE 7.Analog CTCSS 51,Digital CTCSS 107 for each + - 21.MONITOR 8.
Page 5
Specification General Transmitter Frequency 430-470MHz Output Power UHF≤4W Channel TX current HI≤1.6A Digital 6.25KHZ Modulation Channel Spacing Analog 12.5kHz or Maximum frequency ≤±5kHz or 25kHz deviation ≤±2.5kHz Working Temperature -20℃~+60℃ Residucal Radiation <-60dB Voltage 7.4V Standby Current (power About 40mA Save) Receiver Sensitivity...
Page 7
Menu Icon Feature Note Receive CTCSS Message...
Page 8
Scanning Off Set Signal Battery Reverse Frequency ( With this state transmitting receiving will reversed, ) High/Low Channel...
Page 9
Preparation Before Using Install the Antenna Install the antenna as picture shows and rotate it clockwise till tight. Note: Don’t hold the antenna or hang the keys or external mic on the Antenna ,in case of destroying the performance of radio .
Page 10
Install the battery Disassembling of battery Install the batter along the rear case of radio Press the fixed buckle of the battery(P1),then push properly as following pictures show: down the battery off the transceiver(P2)
Page 11
Install and take off the belt clip If necessary ,fix the belt clip with two screws (3*6) as picture shows:: Install disassembly Note:1.When installing the belt clip , do not use any glue to fix screws,otherwise, it will damage the housing. 2.
Page 12
Install external microphone Install the microphone as picture shows,: Charging The battery pack is not fully charger when finished,and please charge it before using The battery can not reach the normal capacity for the first time charging after purchasing or storing it more than two months.However,it will return the normal capacity after charging and discharging repeatedly 3-5 times.。...
Page 13
Charging steps as below: 1. Insert the AC adaptor line to the charging hole of desk-top . 2. Connect the power with AC adaptor. 3.Put Li-ion battery or Radio with battery on the desk top. As following pictures show Note: 1.Please make sure the battery connect with the touching piece of the charging terminal. 2.Green light indicates power on or the battery is full.Red light indicates the charging just beginning.
Basic Functions 1)Power on /Off Turn power on/off by power key . Please input password if setted,operate like this : (1) Input password when LCD display:“――――――” (2)Inputting 0-9 by DTMF keys and display corresponding interface。 (3)After input ,transceiver check password automatically . If yes, then power on ,if not ,back to (1) 2)Select a Channel Choose requested Channel by ( ),199 channels Maximum ,Channel Name can be programmed...
Page 15
(2) Press( )to choose ID code on the contact list。 (3) Press 【PTT】to transmit Note : Press PTT to transmit and get default contact . If not ,transceiver reminds users no contact available . Single call to input contact person . Group call only for program . DTMF (Analog Mode)...
Can receive information once transceiver gets match ID from group/single/All call. Press PTT to communicate within limited time . Menu Operation 1)Menu Operation (1) Press( ) ; (2) Press( )to choose menu ,Long press ( )to get hot menu if transceiver with DTMF keys,press DTMF No.keys to get corresponding menu;...
Page 17
(7) 10s for operating any menu .Once over 10s ,transceiver quit and back tot main interface . Note :1 No limited time for Message editing . 2 while operating ,press PTT to back main interface and no confirmation . 2) Menu Setting List(Digital Mode) Item Chinese English...
Page 20
(1) ±1MHz (2) ±2MHz VFO SCAN (3) ±5MHz 频率模式扫描 (4) PMS (5) BAND (1)英文 (1)ENGLISH LANGUAGE 语言设置 (2)中文 (2)CHINESE Note : The menu with * operation ,please refer to the following details. Menu Operating List(MD Mixed Digital Mode ) Note : Only Menu 26 in the mode of digital transmitting and not reset to dual frequency mode . Item Chinese English...
Page 27
(4) PMS (5) BAND (1)英文 (1)ENGLISH LANGUAGE 语言设置 (2)中文 (2)CHINESE Note : The menu with * operation ,please refer to the following details. Menu Operating List(Analog Mode) Item English English Menu 中文显示 中文菜单项 (1)信道模式 (1) CH MODE MODE (2)记忆模式 (2) MR MODE 工作模式...
Page 30
(4) PMS (5) BAND (1)英文 (1)ENGLISH LANGUAGE 语言设置 (2)中文 (2)CHINESE Note : The menu with * operation ,please refer to the following details. 3) Hot Key Instruction(Main interface long press 【Menu】 ) Function Hot Key Note √ FUNC+1:MODE √ √ FUNC+2:TXP √...
Page 31
Enter Power on function menu。 Factory setting ,clone ,aging Power on +【1】 √ √ √ Menu test ,adjust ,upgrade . Note: press until orange lights Enter BER Tes Mode Main Power on +【2】 √ √ √ Note: Press until Orange lights Interface Enter Hardware upgrade menu .
J>K>L>5 M>N>O>6 P>Q>R>S>7 T>U>V>8 W>X>Y>Z>9 SPACE>0 Note : With Channel mode ,edit channel information by selecting the channel ,and double click on the right side editing box in program software . Programmable Key Function Programmable Key: Side Key 1 by short press、 Side Key 1 by long press、 Side key 2 by short press 、 Side key 2 by long press etc .
Page 33
SCAN Press 【Scan 】 (programmable ) ,then scanning with displayed icon .Press Up/Down to choose scanning setting ,press other keys to quit scanning . Only allowed scanning channel can be scanned .It is waving scanning and once stop the channel ,that means get signals .After signal goes off ,transceiver will stop this channel for certain time ( time can be set by program) ,once get signal again within specified time ,then it will keep scanning .
Page 34
3)Scan Revert Scan Revert Channel fixes the present scanned channel ,press PTT to transmit information during scanning . 4)Scan Delete/Add Set scan delete/add to the present channel by Menu operation and allowed to be scanned or not .Please refer to SCAN .
Page 35
(2) Input DTMF to dial a call with key tone (program by PC) . 2)Dialed Code Store and Transmit(only available with transceiver with DTMF keys) (1) Press DTMF Code ,then display inputing DTMF code。 (2) With finish dialing ,press PTT to transmit . Note : Only 16 DTMF code available once when dialing 3)Auto Dialing (1) Press 【DTMF List】...
Page 36
DPRM 1)Contact List Operation Press 【S2】to add or delete contact person ,press “*” to exit.Present contact person displays on the contact list .Users can choose anyone to edit some information . 1. Press( ) ; 2. Press( )to choose :CONTACTS; 3.
Page 37
2) Press PTT to quit operation when setting . With being in contact list menu, ,press PTT to transmit and ID code will be the present chosed ID . 2)Message Sending 1. Press ( ) ; 2. Press( )to choose:sending box; 3.
Page 38
3)Message Received Checking . 1. Press( ) ; 2. Press( )to choose :MSG INBOX; 3. Press ( )to choose MSG INBOX, then will display the state of message ( :Unread ; Read)and sender name or ID ; 4. Press( )to choose message; 5.
Emergency Calls Hold down for specified time period to transmit an emergency call which can be programmed . Off : Make this function unable ,but still can receive emergency call from other working transceivers . Transceiver alarm : Alarm only itself ( Receive+No code sending+beeper ) Normal : Transceiver can receive call and send alarm code ,and making emergency call.
Page 40
digital mode only . Once voice encryption is on ,other working transceiver can not monitor any information from this encrypted transceiver. Monitor Press Monitor key to monitor any transceiver with unmatched code in digital mode. Monitor other working transceiver with squelch function in analog mode. CTCSS/DCS Turn off the squelch and receive once transceiver present channel receive matched CTCSS/DCS code .
4. Press ( )to choose CTCSS frequency or DCS code; 5. Press 【S2】to exchange among CTCSS、+DCS、+DCS。 6. Press( )to confirm setting and back to previous menu .Press【*】key quit to confirm and back to previous ;Press【S2】to quick exchange CTC/DCS List;Press【PTT】to quit . Note: Press PTT to exit the menu state, Press"*"...
Page 42
transmitting . If not ,TOT count from previous time .. 2)Power Save 1Transceiver will enter power save state ,if there is no signal or no operation (key input, rotating etc) .The power save ratio:1:4. 3)Key Lock Long Press【FUNC】to lock keypad or unlock.. With key lock ,the following keys are still available : 【Emergency】...
Page 43
5)Signal Indication OLED displays present receiving signal level ,please refer to following icon for details. 6)BCLO Once transceiver active BCLO function ,the present channel is prohibit to transmit ,need to waiting for free time to transmit. BCLO Ignored With setting prohibited transmitting on busy channel ,press PTT to prohibit transmit when busy communication ,and hear voice prompts .
Page 44
value is less than minimum ,will cycle to Maximum,otherwise to minimum. 2)Frequency Direct Typing Transceiver with DTMF keys can direct to type frequency number。 For example 1:typing frequency 410.75000 MHz [4], [1], [0] 4 1 0. - - - - - [7], [5], [0] 4 1 0.
Page 45
2)Direct to input Channel No. Key in channel No.with DTMF code ,if transceiver has DTMF keys. For example 1:Input Channel No .001 [0], 0 - - [0], 0 0 - 0 0 1 Note:Transceiver will back to present channle when input invalid channel number . ID Code/DTMF code Input (1)Press【#】to dial menu .
Trouble Shooting Trouble Solution ●The battery pack has been exhausted. Please change a new battery or recharge No reaction when power-on the battery. ● The battery pack may be not installed correctly. Please install it again. ● Please check the frequency and CTCSS/DCS you use are the same as other Unable to talk with other members use in the same group.