Easyclean® Instruction Guide - LG LWS3063ST Owner's Manual

EasyClean® INSTRUCTION GUIDE
1. Remove oven racks and accessories from the oven.
2. Scrape off and remove any burnt-on debris with a
plastic scraper.
Suggested plastic scrapers:
• Hard plastic spatula
• Plastic pan scraper
• Plastic paint scraper
• Old credit card
3. Fill a spray bottle with 1¼ cups (10 oz or 300 ml) of
water and use the spray bottle to thoroughly spray
the inside surfaces of the oven.
4. Use at least ¼ cup (2oz or 50 ml) of the water to
completely saturate the soil on both the walls and in
the corners of the oven.
5. Spray or pour the remaining 1 cup (8 oz or 250 ml)
of water onto the bottom center of the oven cavity.
The indentation on the oven bottom should be fully
covered to submerge all soils. Add water if necessary.
NOTE
Use the "mist" setting on the spray bottle for better
coverage. The entire 1¼ cup (10oz or 300 ml) of
water should be used for each oven cavity cleaned.
Do not spray water directly on the door. Doing so
will result in water dripping to the floor.
6. Close the oven door.
Press the button to select the EasyClean® mode.
Press START.
CAUTION
• Some surfaces may be hot after the EasyClean® cycle.
Wear rubber gloves while cleaning to prevent burns.
• During the EasyClean® cycle, the oven bottom becomes
hot enough to cause burns. Wait until the cycle is over
before wiping the inside surface of the oven.
Failure to do so may result in burns.
• Avoid leaning or resting on the oven door glass while
cleaning the oven cavity.
7. A tone will sound at the end of the 10-minute cycle.
Press CLEAR/OFF to clear the display and end the
tone.
8. After the cleaning cycle and during hand-cleaning,
enough water should remain on the oven bottom
to completely submerge all soils. Add water if
necessary. Place a towel on the floor in front of the
oven to capture any water that may spill out during
hand-cleaning. If you are cleaning the upper oven on
a double oven, it is also best to cover the holes in the
top of the lower oven door with a towel to capture
any water that may drip into the door during hand-
cleaning.
9. Clean the oven cavity immediately after the
EasyClean® cycle by scrubbing with a wet, non-
scratch scouring sponge or pad. (The scouring side
will not scratch the finish.) Some water may spill into
the bottom vents while cleaning,
but it will be captured in a pan
under the oven cavity and will not
hurt the burner.
NOTE
DO NOT use any steel scouring pads, abrasive pads
or cleaners as these materials can permanently
damage the oven surface.
10. Once the oven cavity is cleaned, wipe any excess
water with a clean dry towel. Replace racks and any
other accessories.
11. If some light soils remain, repeat the above steps,
making sure to thoroughly soak the soiled areas.
If stubborn soils remain after multiple EasyClean®
cycles, run the Self Clean cycle. Be sure that the oven
cavity is empty of oven racks and other accessories,
and that the oven cavity surface is dry before
running the Self Clean cycle. Consult the Self Clean
section of your owner's manual for further details.
NOTE
• If you forget to saturate the inside of the oven with
water before starting EasyClean®, press CLEAR/OFF
to end the cycle. Wait for the oven to cool to room
temperature and then spray or pour water into the
oven and start another EasyClean® cycle.
• The cavity gasket may be wet when the
EasyClean® cycle finishes. This is normal. Do not
clean the gasket.
• If mineral deposits remain on the oven bottom
after cleaning, use a cloth or sponge soaked in
vinegar to remove them.
33
MAINTENANCE