Table of Contents
Advertisement
safer
performance.
lubrication and changing accessories. Inspect tool
cord periodically and if damaged have it repaired
by an authorized service facility. Inspect extension
cords periodically and replace, if damaged. Keep
handles dry, clean and free from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when
changing accessories such as blades, bits and
cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension
cords intended for outdoor use.
19. Stay alert.
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of
moving parts, free running of moving parts,
breakage of parts, mounting and any other
conditions that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by an authorized service
center
unless
instruction manual. Have defective switches
replaced by an authorized service facility. Do not
use the tool if the switch does not turn it on and
off.
21. Warning.
The use of any accessory or attachment, other
than those recommended in this instruction
manual or the catalog, may present a risk of
personal injury.
22. Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be
carried out by qualified persons using original
spare parts, otherwise this may result in
considerable danger to the user.
ADDITIONAL SAFETY RULES
1.
Always use eye and ear protection. Other
personal protective equipment such as dust
mask, gloves, helmet and apron should be
Follow
instructions
otherwise
indicated
for
worn.
2.
Always be sure that the tool is switched off
and unplugged before carrying out any work
on the tool.
3.
Accessories must be rated for at least the
speed recommended on the tool warning label.
Wheels and other accessories running over rated
speed can fly apart and cause injury. Maximum
operating speed of accessories should be higher
than the highest no load speed marked on the
tool's nameplate.
4.
Check the backing pad carefully for cracks,
damage
Replace cracked, damaged or deformed pad
immediately.
5.
Check
supported.
6.
Hold the tool firmly.
7.
Keep hands away from rotating parts.
8.
Make sure the abrasive disc is not contacting
the workpiece before the switch is turned on.
9.
When sanding metal surfaces, watch out for
flying sparks. Hold the tool so that sparks fly
away from
flammable materials.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11.
Pay attention that the wheel continues to
rotate after the tool is switched off.
12. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
13. If working place is extremely hot and humid, or
in
this
badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure
operator safety.
14. Do not use the tool on any materials
containing asbestos.
15. Do not use water or grinding lubricant.
16. Ventilate your work area adequately when you
perform sanding operations.
17. Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
18. Always use the correct dust mask/respirator
for the material and application you are
working with.
19. Ensure that ventilation openings are kept clear
ENB048-6
when working in dusty conditions. If it should
become
disconnect the tool from the mains supply
( use non metallic objects ) and avoid
damaging internal parts.
3
or
deformity
before
that
the
workpiece
you
and
other
necessary
to
clear
operation.
is
properly
persons
or
dust,
first
Advertisement
Table of Contents
