C O N T E N T S INTRODUCTION ........................4 SAFETY ............................5 III. TECHNICAL …..........................8 IV. OPERATION ..........................9 INSTALLING & REMOVING ....................15 VI. TROUBLESHOOTING ......................17 VII. CARE AND MAINTENANCE ....................18 VIII. WARRANTY ..........................19 www.pridemobility.com Olympian Autolift...
I N T R O D U C T I O N Welcome to Pride Mobility Products. Congratulations on the purchase of your new lift system. The lift system design combines the most advanced state-of-the-art components with modern, attractive styling.
Battery posts, terminals and related accessories contain lead and lead compounds. Wear goggle and gloves when handling batteries and wash hands after handling. Disposal and recycling. Contact your authorized Pride Provider for information on proper disposal of your Pride product and its packaging. www.pridemobility.com Olympian Autolift...
Page 6
Pride accepts no liability for damage or injury resulting from such use. PRE-LIFT INSPECTION There should be no sharp edges on the Olympian Autolift, the fitting kit or the scooter brackets. If you find any sharp edges, please contact your supplier before use. Make sure that you are completely happy with the operation of your Olympian Autolift before operating it yourself.
Page 7
DOWN (lowering) as well as the IN (into vehicle) and OUT (out of vehicle) operation. Care should be taken that the Olympian Autolift boom and the mobility product that is being lifted are free to move. Olympian Autolifts have the power to break trim and cause harm if not operated correctly.
Material Finish: Powder Coated – Black, Red or Blue COMPONENT DESCRIPTION BOOM SPREADER BAR ‘A’ FRAME CONTROL BOX IN / OUT ACTUATOR HANDSET IN / OUT ACTUATOR FIXING PLATE PIVOT POST ACTUATOR PIN UP/DOWN ACTUATOR RETAINING PIN www.pridemobility.com Olympian Autolift...
4. Check the red led light on the handset is illuminated 5. While retaining the handset move clear of the Hoist and its path of operation 6. Press and hold the left or right button (depending on side of installation) to swing the hoist outwards www.pridemobility.com Olympian Autolift...
Page 10
11. Engage the keyhole plates securely to the lifting bracket. (This bracket will vary depending on what is being lifted) 12. Press and hold up button to raise the scooter/chair up to the upmost position then release button steady the scooter during operation and ensure it does no contact the vehicle. www.pridemobility.com Olympian Autolift...
Page 11
WARNING! Do not continue to hold the down button after the scooter/chair is grounded 18. Press the power button (the indicator red light should no longer be illuminated indicating power OFF) WARNING! Never leave the system with power on when not in use. www.pridemobility.com Olympian Autolift...
Page 12
5. Check the red led light on the handset is illuminated 6. While retaining the handset move clear of the Hoist and its path of operation 7. Press and hold the up button to raise the scooter/chair from the vehicle floor www.pridemobility.com Olympian Autolift...
Page 13
10. Press and hold the down button until the scooter/chair is grounded and there is some slack on the lifting straps. WARNING! Do not continue to hold the down button after the scooter/chair is grounded. 11. Release the key hole plates www.pridemobility.com Olympian Autolift...
Page 14
14. Return the handset back into its docked position – ensure the cable is clear of trapping hazards. 15. Press the power button (the indicator red light should no longer be illuminated indicating power OFF) WARNING! Never leave the system with power on when not in use. www.pridemobility.com Olympian Autolift...
3. Rotate the hoist and align with it actuator 4. Fasten together with the actuator pin – Ensure the pin is fully engaged 5. Fully insert the Retaining Clip into the top pin 6. Clip the power connectors securely together www.pridemobility.com Olympian Autolift...
Page 16
2. Unclip the power connectors 3. Remove retaining clip 4. Partially remove the actuator pin 5. Rotate the actuator away from the hoist 6. Remove actuator pin 7. Slide hoist upwards to remove 8. Store the hoist in a safe location www.pridemobility.com Olympian Autolift...
Is the scooter/wheelchair caught on the vehicle? The Olympian Autolift are all protected by safety cut outs in the Stops during lifting programming, if a load of more than the hoist’s capacity is lifted, the hoist will automatically cut out. Please check this weight with your supplier.
It is recommended that the Olympian Autolift is serviced every year by your authorized Pride Provider. Cleaning: If required the Olympian Autolift can be cleaned with a damp cloth and detergent. Ensure the unit is disconnected before cleaning. Do not immerse in water, do not allow water to run into the electrical connectors or control box and allow to dry before use.
No alteration should be made to the Olympian Autolift by anyone other than a qualified person, as defined by an authorized Pride Provider. In the event of damage or defects in the actuator, the Olympian Autolift should be returned to your authorized Pride Provider for evaluation.
Page 20
V I I I . W A R R A N T Y www.pridemobility.com Olympian Autolift...
Need help?
Do you have a question about the Olympian Autolift and is the answer not in the manual?
Questions and answers
where can I get a hoist fitted please
can I purchase the correct floor mount to fit the olympian lift for a different vehicle from wich it was previously installed?