Remote Sensor Bypass; Remote Engine Starting; Status Light - Crime Guard 850i Operation Manual

REMOTE SENSOR BYPASS

To Activate Remote Sensor Bypass:
Press & Release the "Arm/Lock" Button (
Release the "Auxiliary Output #2" Button ( II )
THE SIREN WILL CHIRP TWICE TO
THE SIREN THEN CHIRPS ONCE
AGAIN TO CONFIRM SENSOR
1st
2nd
2nd
" turning off" the sensor any- time the system is
armed using the transmitter or transceiver. When
1st
the sensor is bypassed, only the sensor zone is by-
passed and all other protected zones will remain fully
operational and vigilant. The sensor zone will reset to
its normal operation the next time the system is armed.
* An optional doorlock interface must be installed

REMOTE ENGINE STARTING

The remote engine starting feature should not be used when
the vehicle is parked in an enclosed structure or garage!
4
Your Crime Guard 850i e system offers the ultimate in comfort and
convenience- remote engine starting. This feature allows the vehicle's interior
to be warmed in the winter or cooled in the summer before you enter the vehicle.
Simply leave the climate controls set to the desired settings when leaving the
vehicle prior to using the remote starting feature.
The following pages explain the remote engine starting operations. If the
vehicle has a manual transmission, a special procedure is required when exiting
the vehicle to enable the ability to remote start. Otherwise, the activation of
remote start is the same for automatic or manual transmission vehicles.
U
) to Arm, then Press &
CONFIRM ARMING
THE PARKING LIGHTS
BYPASS
WILL FLASH TWICE
TO CONFIRM
THE DOORS WILL LOCK
UPON ARMING*
Remote Sensor Bypass allows the option of
Page 18
Feature #2
This feature allows the option of a 30 or 60 second Alarm Duration, which is
when the system has activated in Armed state, sounding the siren and flashing the
parking lights.
Changing the Alarm Duration:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released twice. The system's response will be two siren chirps, and the Status
Light flashing two times, pausing, then repeating. Within 10 seconds, press and
release the transmitter/transceiver's "Arm/Lock" button to set the Alarm Dura-
ARMING
tion for 60 seconds (the siren will chirp once) or the "Disarm/Unlock" button to
set the Alarm Duration for 30 seconds (the siren will chirp twice).
Feature #3
This feature determines how long after the Arming confirmation chirp that
the system becomes fully Armed. The Arming Delay applies to the system
Arming regardless if it occurs from using the transmitter/transceiver, Last Door
Arming or Automatic Rearming.
Programming 3 / 45 Second Arming Delay:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released three times. The system's response will be three siren chirps, and the
Status Light flashing three times, pausing, then repeating. Within 10 seconds,
press and release the transmitter/transceiver's "Disarm/Unlock" button to config-
ure the system with a 45 second Arming Delay (the siren will chirp once) or the
"Arm/Lock" button to configure the system with a 3 second Arming Delay (the
siren will chirp twice).
Feature #4
This feature configures the system to automatically Arm itself 30 seconds
after the vehicle's last door is closed.
Programming Last Door Arming:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released four times. The system's response will be four siren chirps, and the
Status Light flashing four times, pausing, then repeating. Within 10 seconds,
press and release the transmitter/transceiver's "Arm/Lock" button to turn on Last
Door Arming (the siren will chirp once) or the "Disarm/Unlock" button to turn
off Last Door Arming (the siren will chirp twice).
30 or 60 Second Alarm Duration
(Factory Default Setting 60 Seconds)
3 / 45 Second Arming Delay
(Factory Default Setting 3 Second)
Last Door Arming
(Factory Default Setting Off)
Page 31