Pd-F1009 - Pioneer PD-F1009 Service Manual

QQ
3 7 63 1515 0
•
Pin Function
¡N-
Pin Name I/O
o.
1 SQSO
2 SQCK
3 XRST
4 SYSM
5 DATA
6 XLAT
7 CLOK
8 SENS
9 SCLK
10 V
DD
11 ATSK I/O Input and output for unti-shock
12 SPOA
13 SPOB
14 XLON
15 WFCK
16 XUGF
17 XPCK
18 GFS
19 C2PO
20 SCOR
TE
L 13942296513
21 COUT I/O Input and output of track-number count signal
22 MIRR I/O Mirror signal input and output
23 DFCT I/O Defect signal input and output
24 FOK I/O Focus OK signal input and output
25 LOCK I/O
26 MDP
27 SSTP
28 SFDR
29 SRDR
30 TFDR
31 TRDR
32 FFDR
33 FRDR
34 V
SS
35 TEST
36 TEST
37 XTSL
38 VC
39 FE
40 SE
www Notes)
• PCMD is an MSB first. two's complement output.
• GTOP is used to monitor the frame sync protection status. (High:sync protection window released)
• XUGF is the negative pulse for the frame sync derived from the EFM signal. It is the signal before sync protection.
• XPCK is the inverse of the EFM PLL clock. The PLL is designed so that the falling edge of XPLCK and the EFM signal transition point coincide.
.
• GFS goes high when the frame sync and the insertion protection timing match.
• RFCK is derived with the crystal accuracy. This signal has a cycle of 136µs.
• C2PO represents the data error status.
• XROF is generated when the 16K RAM exceeds the ±4F jitter margin.
http://www.xiaoyu163.com
Function
SubQ 80-bit, PCM peak and level data output
O
CD TEXT data output
I Clock input for SQSO readout
I System reset Reset when "L"
I Mute input Mute when "H"
I Serial data input from CPU
Latch input from CPU
I
Serial data is latched at the falling edge.
I Serial data transfer clock input from CPU
O SENS output to CPU
I Clock input for SENS serial-data readout
−
Digital power supply
I Microcomputer extended interface (input A)
I Microcomputer extended interface (input B)
O Microcomputer extended interface (output)
O WFCK output
XUGF output MNT1 and RFCK output by
O
switching the command.
XPLCK output MNT0 output by switching the
O
command.
GFS output MNT3 and XRAOF output by
O
switching the command.
C2PO output GTOP output by switching the
O
command.
Outputs "H" when either subcode sync. S0 or S1 is
O
detected.
GFS is sampled at 460Hz;when GFS is "H", this pin
outputs "H". If GFS is "L" eight consecutive
samples, this pin outputs "L". Input when LKIN="H".
O Servo control output of spindle motor
I Detection signal input of disc innermost
O
Sled drive output
O
O
Tracking drive output
O
O
Focus drive output
O
−
Digital GND
I
TEST pin : normally GND
I
Crystal selector input
I
"L":16.9344MHz , "H":33.8688MHz
I Center voltage input
I Focus error signal input
I Sled error signal input
x ao
y
i
http://www.xiaoyu163.com
8
No. Pin Name
41 TE
42 CE
43 RFDC
44 ADIO
45 AV 0
SS
46 IGEN
47 AV 0
DD
48 ASYO
49 ASYI
50 BIAS
51 RFAC
52 AV 3
SS
53 CLTV
54 FILO
55 FILI
56 PCO
57 AV 3
DD
58 V
SS
59 V
DD
60 DOUT
Q Q
3 6 7 1 3
61 LRCK
62 PCMD
63 BCK
64 EMPH
65 XV
DD
66 XTAI
67 XTAO
68 XV
SS
69 AV 1
DD
70 AOUT1
71 AIN1
72 LOUT1
73 AV 1
SS
74 AV 2
SS
75 LOUT2
76 AIN2
77 AOUT2
78 AV 2
DD
79 RMUT
80 LMUT
u163
.
2 9 9 4 2 8
I/O Function
I Tracking error input
I Center servo analog input
I RF signal input
O OP amplifier output
−
Analog GND
I Constant current input for OP amplifier
−
Analog power supply
O EFM full-swing output ("L"=VSS, "H"=VDD)
I Asymmetry comparate voltage input
I Constant current input of the asymmetry circuit
I EFM signal input
−
Analog GND
I VCO control voltage input for master
O Filter output for master PLL (Slave=digital PLL)
I Filter input for master PLL
O Charge pump output for master PLL
−
Analog power supply
−
Digital GND
−
Digital power supply
O DIGITAL OUT output
1 5 0 5 8 2 9 9 4
O D/A interface LR clock output f=Fs
D/A interface
O
Serial data output (two's complement, MSB first)
O D/A interface Bit clock output
Outputs "H" when the playback disc has emphasis,
O
and "L" when there is no emphasis.
−
Power supply for master clock
Crystal oscillation circuit input
I
Input the external master clock via this pin.
O Crystal oscillation circuit output
−
GND for master clock
−
Analog power supply
O L ch analog output
I L ch OP amp. input
O L ch LINE output
−
Analog GND
−
Analog GND
O R ch LINE output
I R ch OP amp. input
O R ch analog output
−
Analog power supply
O R ch zero detection flag
O L ch zero detection flag
m
co

PD-F1009

9 9
2 8 9 9
57