Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for OneRemote 30017742
Summary of Contents for OneRemote 30017742
-
Page 1: User Manual
PowerLink Switch OneRemote Type 30017742 User Manual 30017742u2uk... -
Page 2: Table Of Contents
Features.............................. 10 Galvanic isolation ........................10 lossless audio pass ........................10 Datalink pass ..........................10 delay at power off ........................10 Installation ............................11 Cable quality ..........................11 Option Programming ......................... 12 Technical specifications ........................14 Connections ..........................14 www.oneremote.dk... -
Page 3: Modes Of Switching
MODES OF SWITCHING The OneRemote PowerLink Switch is developed for use with active (powered) B&O speakers connected with PowerLink DIN cables. Use adaptor cables, if speakers or a source are equipped with RJ45 connectors. The PowerLink Switch makes it possible for two different sound sources to share one set of PowerLink speakers. -
Page 4: Priority Switching Mode
Refer to the chapter Option Programming to program the PowerLink Switch to the Priority Switching Mode, if it has been changed from the factory setting. Example of use in the Priority Switching Mode. BeoSound Encore and a Bang & Olufsen TV sharing BeoLab speakers. www.oneremote.dk... - Page 5 Example of use in the Priority Switching Mode. A NON Bang & Olufsen TV and a BeoSound audio product sharing BeoLab speakers. *1 The TV must have a regulated sound output and a trigger output signal, like a Loewe TV equipped with Audiolink. www.oneremote.dk...
-
Page 6: Last Source Switched On Mode
Refer to the chapter Option Programming on how to select the Last Source Switching Mode. Example of use in the Last Source Switching ON Mode. BeoSound Encore and a Bang & Olufsen TV sharing BeoLab speakers. www.oneremote.dk... -
Page 7: Remote Controlled Switching Mode
Sources programmed for INPUT-0 are ignored. As default setting the LIGHT key has been set to input 0, so the switch will ignore the LIGHT key being pressed. TV will select PL1 and RADIO will select PL2 and so on. www.oneremote.dk... - Page 8 www.oneremote.dk...
- Page 9 Example of use in the Remote Control Switching Mode. A B&O TV and an Apple Airport Express, Bluetooth receiver or DAB radio sharing BeoLab speakers. www.oneremote.dk...
-
Page 10: Features
As the switching is controlled directly from the sources or an IR receiver, the speaker will power off immediately, when no source is selected. When the speaker is powered off, sound signals will be muted using a mechanical relay. www.oneremote.dk... -
Page 11: Installation
INSTALLATION The OneRemote PowerLink Switch, is easily installed. Connect the speakers with PowerLink cable(s). Not included. Connect the two sound sources with appropriate cables. Not included. Connect the mains adaptor. CABLE QUALITY Make sure to use good quality PowerLink cables, preferably double-shielded types, especially if long cables are used. -
Page 12: Option Programming
2 is powered on, No changes have been the switch directs the made. sound signal from it to the speakers, otherwise the sound signal from Green Idle, more than 30 seconds input 1 is selected. passed without receiving data. www.oneremote.dk... - Page 13 Pressing v will hereafter select input 1. Pressing v will hereafter select input 2. See a list of all the programmable source keys in the table on page 6. An option must be entered for every source key used in the set-up. www.oneremote.dk...
-
Page 14: Technical Specifications
25 x 45 x 74 mm Included accessories Power Adaptor 12VDC @ 400mA Euro Not included IR-receiver 455 KHz type 31107834 Cables CONNECTIONS Sockets: DIN 8-pin PowerLink DIN 8-pin PowerLlink DIN 8-pin PowerLink Power 12V DC 300mA Jack 3-conductor, 5 volt www.oneremote.dk...