Braun 5090cc Manual page 11

Model 5040s w&d only:
This appliance is suitable for use in a bath or
shower. For safety reasons this appliance
can only be operated cordlessly.
MultiHeadLock switch (head lock)
To shave hard-to-reach areas (e.g. under the nose)
slide the MultiHeadLock switch (3) down to lock the
shaver head. The shaver head can be locked in five
positions. To change position, move the shaver head
with your thumb and forefinger back or forth. It will
automatically click into the next position.
To set it back into the pivoting position the
MultiHeadLock switch needs to be slid up again.
Models 5090cc/5070cc/5050cc: For automatic
cleaning in the Clean&Charge Station the head lock
should be released.
Long hair trimmer
To trim sideburns, moustache or beard press the
release button (8a) and slide the long hair trimmer
(6) upwards.
Shaving with the cord (models 5090cc/5070cc/
5050cc/5030s/5020s only)
If the shaver has run out of power (discharged), you
may also shave with the shaver connected to an
electrical outlet via the special cord set.
Travel lock
• Activation: By pressing the on/off switch (4) for
3 seconds the shaver is locked. This is confirmed
by a beep sound and the lock symbol
display. Afterwards the display turns off.
• Deactivation: By pressing the on/off switch for
3 seconds the shaver is unlocked again.
Manual cleaning of the shaver
The shaver is suitable for cleaning under
running tab water. Warning: Detach the
shaver from the power supply before
cleaning it in water.
• Switch the shaver on (cordless) and rinse the
shaver head under hot running water. You may use
liquid soap without abrasive substances.
Rinse off all foam and let the shaver run for a few
more seconds.
• Next, switch off the shaver, press the release
button (2) to remove the Foil & Cutter cassette (1)
and let it dry.
• If you regularly clean the shaver under water, then
once a week apply a drop of light machine oil on
top of the Foil & Cutter cassette.
Alternatively, you may clean the shaver using the
brush provided:
• Switch off the shaver. Remove the Foil & Cutter
cassette (1) and tap it out on a flat surface. Using
the brush, clean the inner area of the pivoting
head. Do not clean the cassette with the brush as
this may damage it!
Model 5040s only – foam usage:
After each foam use release the shaver head and
rinse all parts for 30 seconds under warm water.
Clean&Charge Station
for models 5090cc/5070cc/5050cc only
The Clean&Charge Station has been developed for
cleaning, charging, lubricating, disinfecting and
storing your Braun shaver.
12 Station power socket
13 Lift button for cartridge exchange
14 Station-to-shaver contacts
15 Clean&Charge Station display
15a Status light
16 Start button
17 Cleaning cartridge
Installing the Clean&Charge Station (see fig. D)
• Remove the protection foil from the Clean&Charge
Station display.
• Using the special cord set (10), connect the
station power socket (12) to an electrical outlet.
• Press the lift button (13) at the rear side of the
Clean&Charge Station to lift up the housing.
• Hold the cleaning cartridge (17) down on a flat,
stable surface (e.g. table).
• Carefully remove the lid from the cartridge.
• Slide the cartridge from the rear side into the base
in the
of the station until it snaps into place.
• Slowly close the housing by pushing it down until
it locks.
Charging the shaver in the Clean&Charge Station
(see fig. D)
(s. fig. B/C)
Insert the shaver head down into the cleaning station.
Important: The shaver needs to be dry and free
from any foam or soap residue!
The contacts (7) on the back of the shaver need to
align with the contacts (14) in the station. Push the
shaver in the correct position.
A beep sound confirms that the shaver sits properly
in the station. Charging will start automatically.
Model 5090cc: The Clean&Charge Station analyzes
the hygiene status. The status is shown by the
cleaning program indicators
Station display (15) more details see chapter
«Cleaning programs» below.
Cleaning the shaver (see fig. D)
When the cleaning indicator lights up in the shaver
display, insert the shaver into the Clean&Charge
Station, upside down and with the front showing (with
released head lock/contact alignment/beep sound).
in the Clean&Charge
11