Page 1
Installation Manual for Springfree O77 Trampoline Installing the tgoma can be challenging if you Your Product Serial Number is: don’t carefully follow these instructions. To make it easier, we have demonstration videos that will guide you through each step. Visit www.tgoma.com/support to get started.
Page 2
WARNING Please read the Installation Manual before using your tgoma® game system and keep it for future reference. Treat any loaded rod with caution Assembly and disassembly of the until you are sure it is properly trampoline in any way other than what installed or uninstalled.
Page 3
WARNING Please read the Installation Manual before using your tgoma® game system and keep it for future reference. Please read the following precautions carefully Do not use the mat/bed when it is wet. Do not use before you assemble and use the trampoline, the tgoma game system in rainy or wet conditions.
Page 4
LOCATING TEMPLATE 4: Inside Person 5: Inside and Outside Person While the outside person holds the sensor top plate firm, position a sensor Repeat steps 1 - 4 at position 3. mount under the mat, flat side up. Upon completion, turn this template over to position the Align the sensor mount holes with the sensor top plate prongs.
OUTSIDE VIEW INSIDE VIEW NOTE - Have one person position themselves under the trampoline (hereafter known as the Inside Person) while the other person works around the outside of the trampoline (Outside Person). NOTE - Be sure to position the controller at the correct leg position, as indicated. If installed in the wrong location, you will be unable to complete the following steps correctly.
Page 6
OUTSIDE VIEW WARNING - Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well away from any loaded rod. WARNING - Do not use the trampoline unless it is completely assembled. Failure to follow these instructions may cause rods to break or eject from the trampoline frame.
Page 7
OUTSIDE VIEW LOCATING TEMPLATE 4: Inside Person 5: Inside and Outside Person While the outside person holds the sensor top plate firm, position a sensor Repeat steps 1 - 4 at position 3. mount under the mat, flat side up. Upon completion, turn this template over to position the Align the sensor mount holes with the sensor top plate prongs.
Page 8
BOTTOM VIEW BEFORE TOP VIEW BEFORE BOTTOM VIEW AFTER TOP VIEW AFTER WARNING - Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well away from any loaded rod. NOTE - Be sure not to fasten the small cable ties during this step. Inside Person: Feed a small cable tie up through one of the holes in the sensor mount.
Page 9
INSIDE VIEW OUTSIDE VIEW WARNING - Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well away from any loaded rod. Inside Person: Starting at sensor position 2, locate the first mat rod holder to the left. Install a cable clip at the front of the mat rod holder pocket, as shown.
Page 10
OUTSIDE VIEW INSIDE VIEW BOTTOM VIEW BEFORE BOTTOM VIEW AFTER NOTE - Before proceeding, double check that each cable clip is pushed fully onto the edge of its pocket and that there are no cable clips installed in front of any of the sensor positions. TIP - If you are having trouble inserting the cable sensors into the sensor mounts, try flipping them over.
Page 11
OUTSIDE VIEW WARNING - Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well away from any loaded rod. WARNING - Never attempt to remove a black net rod from its net rod pocket or disengage (unlock) the rod sleeve while the black net rod is under tension.
Page 12
INSIDE VIEW INSIDE VIEW INSIDE VIEW NOTE - Cable A with the yellow tag must be plugged into socket A and cable B with the white tag into socket B. The cable plugs and controller sockets are ‘keyed’ (ie, they will only fit correctly in one position). Line up the green post in the cable plug with the slot in the controller socket.
Page 13
WARNING - Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well away from any loaded rod. NOTE - Ensure the tablet holder is in the correct orientation. TIP - The software’s default position for the tablet holder is opposite the door. Consult your Software User Guide for how to position the tablet holder in alternative locations.
Page 14
Minimum Tablet Specifications • iPad 3 or more recent, iPad Mini & iPad Air. ® • Bluetooth 4 (also known as LE) or more recent Apple Tablets: ® (NOTE: iPads 1 and 2 cannot be used because they do not have Bluetooth 4). •...
Page 15
Installation Manual for Springfree Trampoline Installing the tgoma can be challenging if you Your Product Serial Number is: Your serial number don’t carefully follow these instructions. To make it easier, we have demonstration videos that will guide you through each step.
Page 16
WARNING - To protect the batteries store the battery pack indoors when not in use. NOTE - When you turn the controller on to connect to your tablet, ensure there is nobody standing/sitting on, or leaning against, the trampoline for 15 seconds. This allows the controller to correctly set the sensors for accuracy.
Page 17
WARNING - Do not leave your tablet outside in wet weather. Once you have completed setting up your tgoma on your tablet, hold your tablet in a landscape orientation and place the bottom edge onto the bottom jaw of the clamp. Pull the tablet down on the bottom jaw until the clamp opens wide enough for the tablet to fit between the top and bottom jaws of the clamp.
Page 18
Games: where your games and JumpFit: where you access News & Events: where you see apps live once you’ve down- your jump stats via the news and events to participate loaded them. JumpTracker, or set goals to achieve. Settings: where you set up Store: where you preview all Users: tap this to create a new tgoma (make sure you select...
Page 19
PRODUCT SPECIFICATION TABLE Name of product as described in the marketing literature tgoma Game System Part number(s) TGR54000, TGR79000, TGO77000, TGO92000, TGS113000, TGS155000 Operating temperature range 0°C to +40°C (+32°F to +104°F) Storage temperature range 0°C to +40°C (+32°F to +104°F) Operating humidity 10% to 90% non-condensing RF Compliances...
Assembly Instructions. This warranty provides, at no extra cost to you, all parts necessary to ensure your accessory is in proper working condition throughout the warranty period. For information related to the warranty and tgoma software, check www.springfree.com/tgoma. WHAT IS NOT COVERED This warranty is subject to the following terms: tgoma NZ Ltd.
Need help?
Do you have a question about the O77 and is the answer not in the manual?
Questions and answers