Do you have a question about the MS 251 and is the answer not in the manual?
Questions and answers
Richard Muelheim
March 14, 2025
I do not have spark on my MS251C. Just died after 1 pull.
1 comments:
Mr. Anderson
March 14, 2025
Possible causes for a Stihl MS 251C having no spark after one pull include:
1. Faulty Spark Plug – Even if it looks fine, the spark plug may be defective or fouled. Try replacing it. 2. Disconnected or Damaged Ignition Wire – Check if the ignition wire is securely connected and not damaged. 3. Ignition Coil Failure – A faulty ignition coil can prevent spark generation. 4. Kill Switch Malfunction – Ensure the kill switch is in the correct position and not shorting the ignition circuit. 5. Flywheel Magnet Misalignment – If the flywheel magnets are misaligned or dirty, they may not generate spark properly. 6. Grounding Issue – A short circuit in the wiring could be grounding the ignition system, preventing a spark.
Inspect these components systematically to diagnose and resolve the issue.
Page 1
Instruction Manual Manual de instrucciones WARNING To reduce the risk of kickback injury use STIHL reduced kickback bar and STIHL low kickback chain as specified in this manual or other available low kickback components. ADVERTENCIA Para reducir el riesgo de lesionarse como resultado de un...
Disposal www.stihlusa.com. Tensioning the Saw Chain (quick STIHL Incorporated Federal chain tensioner) Contact your STIHL dealer or the STIHL Emission Control Warranty Checking Chain Tension distributor for your area if you do not Statement understand any of the instructions in this...
DANGER operation Indicates an imminent risk of severe or fatal injury. This Instruction Manual refers to a Handle heating STIHL chain saw, also called a machine in this Instruction Manual. WARNING Indicates a hazardous situation which, if Pictograms Operate decompression...
Most of these safety precautions and WARNING WARNING warnings apply to the use of all STIHL Be alert – if you get tired, take a break. Reactive forces, including kickback, can chain saws. Different models may have Tiredness may result in loss of control.
Page 6
– go barefoot. available with an anti-vibration WARNING ("AV") system designed to reduce The ignition system of the STIHL unit Always wear heavy-duty the transmission of vibrations produces an electromagnetic field of a work gloves (e.g. made of created by the chain saw to the very low intensity.
Page 7
Although certain protection complying with unauthorized attachments are useable ANSI Z87 "+" (or your with STIHL chain saws, their use may, in applicable national stand- fact, be extremely dangerous. ard). If there is a risk of injury to your face, STIHL...
Page 8
To do this with this STIHL cap, raise the In order to reduce the risk of burns and grip on the top of the cap until it is upright other personal injury from escaping gas at a 90°...
Page 9
(with the grip up) until it drops fully are leaks or damage – risk of fire! Have into the tank opening. Next, twist the the chain saw repaired by a STIHL cap counterclockwise as far as it will servicing dealer before using it.
Page 10
Chain" of your instruction manual. grease or resin in order for you to trigger lockout is depressed (releasing STIHL Oilomatic saw chain, guide bar maintain a firm grip and properly control the brake) in order to blip the throttle and sprocket must match each other in your chain saw .
Page 11
If you cannot set the correct idle speed, reactive forces). To reduce this risk, from skating or bouncing have your STIHL dealer check your always engage the chain brake before along the limb or log. chain saw and make proper adjustments starting.
Page 12
(e. g. during a work break), shut it attachment whenever the engine is off and make sure that unauthorized running. Stand to the left of cut while persons do not use it. bucking. MS 251, MS 251 C...
Page 13
Follow the recommendations of MS 251, MS 251 C...
Page 14
In case of doubt, have it Never modify your muffler. Any can then increase the risk of injury, e. g., checked by your STIHL servicing dealer. modification could cause an increase in from the saw chain moving while the...
Page 15
If you experience loss of performance and you suspect a clogged screen, have your muffler maintained by a STIHL servicing dealer. Some state or federal laws or regulations may require a properly maintained spark arrester for certain uses.
Page 16
Some a kickback test machine. STIHL bar and saw chain types are designed to reduce kickback forces. STIHL recommends the use of reduced kickback bars and low kickback chains.
Page 17
Kickback Injury The computer derived angles of the chain saw kickback standard may bear Stihl recommends the use of green no relationship to actual kickback bar labeled reduced kickback bars and low rotation angles that may occur in real life kickback saw chains on your chain saw cutting situations.
Page 18
Kickback Bars kickback situations. In order for the STIHL offers a variety of bars and saw Quickstop to reduce the risk of kickback WARNING chains. STIHL reduced kickback bars...
Page 19
Do not mount a bow guide on any STIHL kickback situations: the 45° computer derived kickback chain saw. Any chain saw equipped with angle of the chain saw standard.
Page 20
Limbing wood. 2. The risk of pull-in may also be Limbing is removing the branches from a reduced by using wedges to open fallen tree. the kerf or cut. MS 251, MS 251 C...
Page 21
Sharp slivers of wood may be caught and flung in the direction of the Felling operator of the saw. Felling is cutting down a tree. Before felling a tree, consider carefully all conditions which may affect the direction of fall. MS 251, MS 251 C...
Page 22
When felling on a slope, the operator (A) and about at a 45° angle. Place all should stand on the uphill side if tools and equipment a safe distance possible. away from the tree, but not on the escape paths. MS 251, MS 251 C...
Page 23
Make second cut from below at Make second cut horizontal. want the tree to fall. approx. 40 degree angle. Remove resulting 45° piece. Remove resulting 90° piece. MS 251, MS 251 C...
Page 24
Drive wedges into the felling cut where necessary to control the fall. WARNING If the tip of the bar contacts a wedge, it may cause kickback. Wedges should be of wood or plastic – never steel, which can damage the chain. MS 251, MS 251 C...
Page 25
For the sectioning method make the first notch. part of the felling cut with the guide bar fanning in toward the hinge. Then, using the bumper spike as a pivot, reposition the saw for the next cut. MS 251, MS 251 C...
Page 26
Use of tree when it is about to fall, since part of non-STIHL parts may cause serious or the trunk may split and come back fatal injury. towards the operator (barber-chairing),...
Page 27
In order for the chain brake on your WARNING STIHL chain saw to properly perform its Store chain saw in a dry place and away function of reducing the risk of kickback from children. Before storing for longer...
If non-matching components are used, the cutting attachment may be damaged Turn the screw (1) beyond repair after a short period of counterclockwise until the tensioner operation. slide (2) butts against the left end of the housing slot. MS 251, MS 251 C...
Go to chapter on "Tensioning the Saw Chain" WARNING Wear work gloves to protect your hands from the sharp cutters. Fit the chain – start at the bar nose. Remove and reverse tensioning gear (1) MS 251, MS 251 C...
Page 30
(3) relative to one another screw (3); the head of the rear collar screw must protrude into the oblong hole Insert and tighten screw (2) WARNING Put on protective gloves – risk of injury by the sharp cutters. MS 251, MS 251 C...
Check chain tension frequently – see chapter on "Operating Instructions". When fitting the chain sprocket cover, the teeth of the adjusting wheel and the tensioning gear must mesh; if necessary, MS 251, MS 251 C...
Checking Chain Tension Fuel (quick chain tensioner) This engine is certified to operate on unleaded gasoline and the STIHL two- stroke engine oil at a mix ratio of 50:1. Your engine requires a mixture of high- quality gasoline and two-stroke air cooled engine oil.
Page 33
STIHL MotoMix uses STIHL HP Ultra using fuel with the same ethanol two-stroke engine oil suited for high content. performance engines. Use only STIHL two-stroke engine oil or For further details, see equivalent high-quality two-stroke www.STIHLusa.com/ethanol engine oils that are designed for use only in air cooled two-cycle engines.
Push the filler cap down as far as it cap carefully so as to allow any pressure Markings on filler cap and housing must will go. build-up in the tank to release slowly align. MS 251, MS 251 C...
Page 35
Right: Base of filler cap is in the cor- Flip the handle down. rect position – interior marking is below the clip. It does not align with the exte- rior marking. MS 251, MS 251 C...
Preparations recommended. NOTICE Biological chain oil must be resistant to aging (e.g. STIHL BioPlus), since it will otherwise quickly turn to resin. This results in hard deposits that are difficult to remove, especially in the area of the chain drive and chain. It may even cause the oil pump to seize.
"Checking Chain Tension". if the forces are sufficiently high. The hand guard is accelerated toward the bar nose - even if your left hand is not behind the hand guard, e.g. during a MS 251, MS 251 C...
It is necessary to have it serviced and maintained regularly by trained It is usually necessary to change the personnel, such as your STIHL servicing setting of the idle speed screw (LA) after dealer, at the following intervals: every correction to the low speed Use a screwdriver to pry the shutter screw (L) –...
– Setting the Master Control Lever chamber. To move the Master Control lever from the normal run position (F) to choke closed (l), press down the throttle trigger lockout and squeeze the throttle MS 251, MS 251 C...
Page 40
Hold the saw firmly on the ground be under the handle. with your left hand on the front handle – your thumb should be under the handle. Put your right foot into the rear handle and press down. MS 251, MS 251 C...
Page 41
Press down the trigger lockout (2) times to prime the fuel system. and pull the throttle trigger (3) at the same time. Set Master Control lever (4) to: MS 251, MS 251 C...
Page 42
Dry the spark plug. The chain brake is now disengaged – Crank the engine several times with your saw is ready for operation. the starter to clear the combustion chamber. Refit the spark plug – see "Spark Plug". MS 251, MS 251 C...
Slacken off the chain if you have retensioned it at operating Check chain tension frequently temperature during work. A new saw chain must be retensioned more frequently than one that has been in use already for an extended period. MS 251, MS 251 C...
Measure the groove depth – with the scale on the filing gauge (special accessory) – in the area used most for cutting. Chain Chain pitch Minimum type groove depth Picco 1/4" P 0.16" (4.0 mm) Rapid 1/4" 0.16" (4.0 mm) MS 251, MS 251 C...
(e.g. powder or drifting snow) or very dusty work areas. If knocking-out or blowing-out does not suffice, or in the case of stubborn dirt or stuck filter fabric, the filter must be subjected to a thorough cleaning. MS 251, MS 251 C...
English Thorough filter cleaning Engine Management Adjusting the Carburetor Wash the filter in STIHL special- purpose cleaner (special Exhaust emissions are controlled by the accessory) or a clean, non- Basic information design of the fundamental engine flammable cleaning liquid (e. g., parameters and components (e.g.
Speed erratic when idling; poor acceleration (despite standard setting of low speed adjusting screw) The idle setting is too lean. Carefully turn the low speed adjusting screw (L) counterclockwise until the engine runs smoothly and accelerates properly. MS 251, MS 251 C...
– use only spark plugs authorized by dirty air filter, – STIHL. Always press the spark plug boot (1) snugly onto the spark plug unfavorable running conditions, e.g. – terminal (2). operating at part throttle.
(special accessory) to test children and other unauthorized persons. Using two saw chains in alternation helps preserve the chain sprocket. Use only STIHL original chain sprockets to help ensure reliable functioning of the chain brake. MS 251, MS 251 C...
– especially depth gauges powerheads with Quickstop Plus that are too low – can lead to increased chain brake system, depress kickback tendency of the chain saw – throttle trigger lockout beforehand risk of injury! MS 251, MS 251 C...
Page 51
The chain pitch marking (a) is embossed Sharpening angle Use a file holder in the area of the depth gauge of each STIHL saw chains are sharpened with a Always use a file holder (special cutter. 30° sharpening angle. Ripping chains, accessory, see table "Sharpening tools")
Page 52
The depth gauge determines the depth guide bar) in accordance with the to which the cutter penetrates the wood specified angle – according to the and thus the chip thickness. MS 251, MS 251 C...
Page 53
5605 007 1029 0.404 (10.26) 5.5 (7/32) 5605 772 5506 5605 750 4330 1106 893 4000 0814 252 3356 5605 007 1030 consisting of file holder with round file, taper square file and file gauge MS 251, MS 251 C...
Lubricating oil tank Clean Chain lubrication Check Check, pay attention to sharpness Saw chain Check chain tension Sharpen Check (wear, damage) Clean and turn over Guide bar Deburr Replace Chain sprocket Check Clean Air filter Replace MS 251, MS 251 C...
Page 55
Safety information label Replace STIHL recommends STIHL servicing dealers During initial use of professional chain saws (with a power output of 3.4 kW or more), tighten the cylinder block screws after 10 to 20 hours of operation MS 251, MS 251 C...
18 Front Handle (Handlebar) 19 Spark Plug Boot 20 Starter Grip 21 Fuel Filler Cap 22 Master Control Lever 23 Throttle Trigger 24 Throttle Trigger Lockout 25 Rear Handle 26 Rear Hand Guard Serial Number Depending on Model MS 251, MS 251 C...
Page 57
Toothed stop for holding saw steady The grip of the pull starter, for against wood. starting the engine. 11 Guide Bar 21 Fuel Filler Cap Supports and guides the saw chain. For closing the fuel tank. MS 251, MS 251 C...
(4.9 kg) Picco Micro 3 (63 PM3) Type 3636 Displacement: 2.78 cu. in. (45.6 MS 251 C with quick chain Picco Super 3 (63 PS3) Type 3616 tensioner and 11.5 lbs. Picco Duro (63 PD3) Type 3612 Easy2Start: (5.2 kg)
Since new bar/chain combinations may has been performed by an authorized be developed after publication of this STIHL servicing dealer using genuine Manual, ask your STIHL dealer for the STIHL replacement parts. Serial number latest STIHL recommendations. Genuine STIHL parts can be identified...
STIHL products must not be thrown in meet the U.S. EPA regulations for small manual. STIHL Incorporated the garbage can. Take the product, non road engines.
Page 61
Fly Wheel – STIHL Incorporated will charge you for off-road equipment engine will be the cost of the emission test. Mechanical Spark Plug – designed, built and equipped, at the time...
Service ® STIHL Cutquik ® STIHL DUROMATIC Bring the product to any authorized STIHL Registered Trademarks ® STIHL Quickstop STIHL servicing dealer and present the signed warranty card. ® STIHL ROLLOMATIC ® STIHL ® STIHL WOOD BOSS Maintenance Requirements ®...
Page 63
STIHL SuperCut ™ TapAction ™ TrimCut ™ This listing of trademarks is subject to change. Any unauthorized use of these trademarks without the express written consent of ANDREAS STIHL AG & Co. KG, Waiblingen is strictly prohibited. MS 251, MS 251 C...
Page 64
(tensor rápido de la cadena) Comuníquese con su representante de Incorporated sobre sistemas de Revisión de tensión de la cadena STIHL o el distribuidor de STIHL para su control de emisiones según normas zona si no se entiende alguna de las Combustible...
Muchas de las instrucciones de uso y seguridad vienen acompañadas de Aplicación y soltado del ilustraciones. freno de la cadena STIHL La filosofía de STIHL es mejorar Quickstop continuamente todos sus productos. Los pasos individuales o Como resultado de ello, periódicamente procedimientos descritos en el manual Sentido de rotación de la...
Pida a su concesionario STIHL que le necesario tomar medi- enseñe el manejo de la motosierra. das especiales de ADVERTENCIA...
Page 67
ADVERTENCIA temperatura, producen entumecimiento y ardor y pueden provocar trastornos Para reducir el riesgo de lesiones el nerviosos y circulatorios, así como operador debe usar el equipo protector necrosis de los tejidos. adecuado. MS 251, MS 251 C...
Page 68
STIHL reco- para usarse con el modelo específico de o cualquier cosa que mienda que también se STIHL. Si bien es posible conectar a las pueda engancharse en use una careta o protec- motosierras de STIHL ciertos las ramas, matorrales o...
Page 69
Combustible combustible. de aserrado. Siempre aplique el freno La motosierra STIHL utiliza una mezcla de la cadena al llevar la motosierra por Para reducir el riesgo de sufrir de aceite-gasolina como combustible más de unos pocos pasos.
Page 70
Compruebe que no exis- Tapa desalineada, dañada o rota ten fugas de combustible Para hacer esto con esta tapa STIHL, mientras llena el tanque y levante la empuñadura en la parte Si la tapa no encaja completamente superior de la tapa hasta dejarla vertical...
Page 71
La cadena de Siempre revise la motosierra para aserrado Oilomatic, la espada y el piñón comprobar que está en buenas STIHL deben coincidir entre sí en condiciones y que funciona cuanto a calibre y paso. Antes de correctamente antes de arrancarla, en...
Page 72
Si la motosierra control seguro. del mango trasero y haga presión hacia tiene el sistema de freno de cadena abajo. Con la mano derecha tire Quickstop Plus, no bastará con aplicar MS 251, MS 251 C...
Page 73
Si no puede regular correctamente el antes de iniciar el trabajo de corte. La sujete la manija delantera de la ralentí, pida a su concesionario STIHL única excepción a esta regla es cuando motosierra firmemente con la mano que revise la motosierra y haga los se está...
Page 74
Mantenga los pies bien apoyados y equilibrados en todo momento. Se debe tener cuidado especial cuando las condiciones del suelo son resbaladizas (suelo húmedo, nieve) y en terreno difícil y con mucha vegetación. Sea sumamente precavido cuando trabaje MS 251, MS 251 C...
Page 75
Trabaje con mucho cuidado. que se puedan concentrarse. ADVERTENCIA La motosierra es una máquina para una sola persona. No deje que otras personas estén en el lugar de trabajo, MS 251, MS 251 C...
Page 76
Esto incluye el polvo, asbesto. Si por cualquier motivo cree especialmente de las maderas duras, que está cortando asbesto, suspenda el pero también de algunas maderas MS 251, MS 251 C...
Page 77
Tome precauciones especiales al cortar dañada. En caso de dudas, pida que el madera astillada debido al riesgo de concesionario de servicio de STIHL la ADVERTENCIA lesiones causadas por las astillas revise. afiladas que pueden atraparse y salir Su motosierra está...
Page 78
Si la mezcla de gasolina y aceite está correcta (no es demasiado rica), en condiciones normales el chispero quedará limpio como resultado del calor del silenciador y no necesitará servicio ni mantenimiento. Si el MS 251, MS 251 C...
Page 79
– ADVERTENCIA Contragolpe: Puede ocurrir un contragolpe, por ejemplo, cuando la cadena cerca del cuadrante superior de la punta de la espada entre en contacto con la madera o quede aprisionada al cortar una rama, MS 251, MS 251 C...
Page 80
STIHL recomienda el uso de espadas las combinaciones de espadas y aserrado de bajo contragolpe, – de contragolpe reducido y cadenas de...
Page 81
Lleve la motosierra al concesionario de freno de cadena Quickstop, se servicio de STIHL de su localidad. No inhabilitará el mecanismo de activación use la motosierra hasta haber corregido del freno de la cadena.
Page 82
Las puede adquirir a través de su anteriormente en "Ajustes contragolpes. concesionario STIHL. importantes"). STIHL recomienda el uso de sus Cadena de aserrado de bajo espadas de contragolpe reducido con ADVERTENCIA contragolpe y espadas de contragolpe etiqueta verde, cadenas de aserrado de reducido Aunque la sierra esté...
Page 83
No extienda los brazos más allá de STIHL ha desarrollado una cadena de utiliza con las cadenas de aserrado de lo necesario. aserrado de bajo contragolpe para su bajo contragolpe de STIHL con etiqueta No corte más arriba de la altura de...
Page 84
Si la sierra queda aprisionada, enredarse fácilmente en la cadena de apague el motor y levante la rama para aserrado, salir despedidos en dirección poder retirar la sierra. a usted o hacerle perder el equilibrio. MS 251, MS 251 C...
Page 85
Si se encuentra en Tala una ladera, sitúese cerro arriba del tronco. Esté atento a los troncos que pueden rodar. La tala consiste en cortar un árbol hasta que caiga. Corte solamente un tronco a la vez. MS 251, MS 251 C...
Page 86
Siempre busque las ramas quebradas o muertas que puedan soltarse con la vibración y caerle encima. Cuando esté talando en una ladera, siempre que sea posible sitúese en el lado cuesta arriba. MS 251, MS 251 C...
Page 87
Haga un segundo corte desde Haga un segundo corte horizontal. usted desea que caiga el árbol. abajo en un ángulo de Quite el pedazo de 45° resultante. aproximadamente 40°. Quite el pedazo de 90° resultante. MS 251, MS 251 C...
Page 88
ADVERTENCIA Si la punta de la espada hace contacto con una cuña, puede producirse un contragolpe. Las cuñas deben ser de madera o de plástico, pero jamás de acero porque se dañaría la cadena. MS 251, MS 251 C...
Page 89
Después, usando la púa de tope como pivote, cambie de posición la sierra para el próximo corte. MS 251, MS 251 C...
Page 90
Agrande el corte por penetración como MANTENIMIENTO, REPARACIÓN Y únicamente por el concesionario de se muestra en la ilustración. ALMACENAMIENTO servicio de STIHL. Por ejemplo, si se utilizan herramientas inadecuadas para ADVERTENCIA retirar el volante del motor o para sujetar Los trabajos de mantenimiento,...
Page 91
Por estas razones, toda motosierra de ADVERTENCIA reglamentos relacionados con los STIHL deberá ser entregada a personal requisitos de protección contra No pruebe nunca el sistema de experto, tal como el personal del incendios.
(1) debe corresponder con el ancho de la ranura de la espada (3). El uso de componentes no apareados puede resultar en daños permanentes del accesorio de corte dentro de poco tiempo de uso. MS 251, MS 251 C...
Use guantes para proteger las manos deslizante (2) tope contra el de los cortadores afilados. extremo izquierdo de la ranura de la Coloque la cadena – empiece por la caja. punta de la espada. MS 251, MS 251 C...
(3). Retire la cubierta del piñón (3) de la cadena Montaje del engranaje tensor Inserte y apriete el tornillo (2) Retire e invierta el engranaje tensor (1). MS 251, MS 251 C...
Page 95
(vea la flecha) usuario. y gire el engranaje tensor hacia la izquierda hasta su tope. Coloque la cubierta del piñón, deslizando las orejetas guía en las aberturas correspondientes de la caja del motor MS 251, MS 251 C...
– vea el capítulo que las que han estado en uso por algún "Instrucciones de manejo". tiempo. Revise la tensión de la cadena frecuentemente – vea el capítulo "Instrucciones de manejo". MS 251, MS 251 C...
50 a 1 de etanol. enfriados por agua o por aire (por gasolina sin plomo y aceite STIHL para ejemplo, en motores marinos fuera de motores de dos tiempos. borda, motonieves, sierras de cadenas,...
Page 99
A derecha: La base de la tapa de lle- nado está en posición Empuje la tapa hacia abajo hasta correcta – la marca inte- donde sea posible. rior está debajo de la pinza. No queda alineada con la marca exterior. MS 251, MS 251 C...
Preparaciones cadenas y espadas. Se recomienda el aceite STIHL BioPlus, el cual es Con la tapa de llenado colocada en rápidamente biodegradable. el cuello de llenado, gírela en sentido contrahorario hasta que INDICACIÓN...
Después del rodaje inicial de la cadena, se activa por inercia en ciertas revise su tensión y ajústela de ser situaciones de contragolpe. necesario – vea el capítulo "Revisión de la tensión de la cadena". MS 251, MS 251 C...
única excepción a esta regla es cuando competente, como el concesionario se está probando el funcionamiento del STIHL, cada vez que se cumplan los freno de la cadena. siguientes intervalos: El funcionamiento a velocidad alta con...
Obturador de estrangulador De ser necesario, convierta el filtro cerrado (l) – esta posición se usa de aire – vea "Sistema de filtro de para arrancar un motor frío. aire" MS 251, MS 251 C...
Page 104
(l) Si el motor está frío – Si el motor se apaga al accionar el – acelerador después del arranque. Si se ha dejado que se agote el – combustible (el motor se para). MS 251, MS 251 C...
Page 105
Máquinas sin bomba de combustible de mantenerse alejadas de la zona general mano adicional: Si el motor es nuevo o de uso de la sierra. después de un período prolongado sin Respete las medidas de seguridad. MS 251, MS 251 C...
Page 106
Posición de aceleración de vacío. arranque (n) Si el motor está caliente, es decir ha – estado en marcha durante aprox. un minuto. Sujete y arranque la motosierra de la manera descrita. MS 251, MS 251 C...
De ser necesario, cambie al ajuste (cadena bloqueada) dañará para uso durante el invierno – vea rápidamente el bloque de motor y el "Manejo durante el invierno". mando de la cadena (embrague, freno de la cadena). MS 251, MS 251 C...
Vuelva a colocar la envuelta y apriete los tornillos Filtro HD2 (armazón de filtro negro, material de filtro con pliegues) para condiciones de invierno extremas (por ejemplo, nieve fina o desplazada por el viento) o áreas de trabajo muy polvorientas. MS 251, MS 251 C...
Golpee el filtro para limpiarlo o hasta que se enganche – el logotipo sóplelo con un chorro de aire "STIHL" debe quedar en posición comprimido de adentro hacia horizontal afuera. Retire la envuelta – vea "Envuelta" MS 251, MS 251 C...
Si el ajuste es demasiado pobre, existe está funcionando a marcha en vacío, riesgo de dañar el motor debido a una pida a su concesionario de servicio que lubricación insuficiente y revise la motosierra. sobrecalentamiento. MS 251, MS 251 C...
Instale el tornillo Retire la envuelta – vea "Envuelta" filtro de aire sucio, – condiciones desfavorables de – funcionamiento, por ejemplo, funcionando a aceleración parcial. Quite el casquillo de la bujía Destornille la bujía MS 251, MS 251 C...
Esto podría personas no autorizadas. causar lesiones personales graves o daños graves a la propiedad. Use únicamente bujías de tipo resistor con bornes sólidos, sin roscas. MS 251, MS 251 C...
– esto causa un Angulo de afilado aumento en el esfuerzo físico, un Las cadenas de aserrado STIHL se aumento en las vibraciones, cortes no afilan con un ángulo de 30°. Las satisfactorios y un aumento en el cadenas desgarradoras, que se afilan desgaste.
Page 116
"Herramientas de afilado") – una Para eliminar las rebabas de herramienta universal para revisar el afilado, utilice un trozo de madera afilado y ángulo de las placas laterales, maciza Revise el ángulo con un calibrador MS 251, MS 251 C...
Page 117
Calibrador de baja al mismo tiempo que el calibrador Si los calibradores de profundidad profundidad de profundidad del cortador. quedan muy bajos, se aumenta la Distancia (a) propensidad de contragolpes con la motosierra. pulg (mm) (pulg) MS 251, MS 251 C...
Page 118
0,404 (10,26) 5,5 (7/32) 5605 772 5506 5605 750 4330 1106 893 4000 0814 252 3356 5605 007 1030 consiste de un portalima con lima redonda, una lima cuadrada ahusada y el calibrador de afilado MS 251, MS 251 C...
Lubricación de la cadena Revisar Revise, preste atención al afilado Cadena de aserrado Revisar la tensión de la cadena Afilar Revisar (desgaste, daño) Limpiar e invertir Espada Quitar las rebabas Reemplazar Piñón de la cadena Revisar MS 251, MS 251 C...
Page 120
Etiqueta de información de seguridad Reemplazar STIHL recomienda acudir a un concesionario STIHL para servicio Durante el uso inicial de motosierras profesionales (con una potencia entregada de 3,4 kW o más), apriete los tornillos del bloque de cilindros cada 10 a 20...
21 Tapa de llenado de combustible 22 Palanca de control maestro 23 Gatillo de aceleración 24 Bloqueo de gatillo de aceleración 25 Mango trasero 26 Protector trasero de la mano Número de serie Dependiendo del modelo MS 251, MS 251 C...
Page 122
(No se muestra; vea el capítulo del mango. También sirve de Permite el ajuste preciso de la "Tensado de la cadena de palanca para activar el freno de la tensión de la cadena. aserrado") cadena. MS 251, MS 251 C...
C = 50 horas Motor Bomba de aceite de émbolo giratorio controlada por velocidad y plenamente automática Motor STIHL de un cilindro, dos tiempos Capacidad del depó- MS 251, MS 251 C sito de aceite: 0,2 l (6,7 oz. fl.)
Cadena de aserrado de 0,325 pulg Pedido de piezas de norma ANSI/OPEI B175.1-2012 cuando repuesto Cadena de aserrado STIHL de bajo se utiliza en este modelo de motosierra contragolpe (con etiqueta verde) (consulte el capítulo "Medidas de Sírvase anotar el modelo de su seguridad y Técnicas de manejo"):...
En los EE.UU., los No se debe botar los aparatos STIHL en realizadas las reparaciones serán nuevos motores pequeños para equipos el basurero. Lleve el producto, los aceptados únicamente si las mismas...
Page 126
STIHL de emisiones, la pieza será reparada o firma y remite la tarjeta de garantía a tan pronto surja el problema.
Page 127
(Módulo de encendido la calidad y la proporción de la mezcla de STIHL Incorporated o en un o unidad de control electrónica) de combustible y aceite pueden exigir laboratorio de ensayos independiente.
® AutoCut FixCut ™ ® FARM BOSS IntelliCarb ™ ® iCademy Master Control Lever ™ ® MAGNUM Micro ™ ® MasterWrench Service Pro Mark ™ ® MotoMix Quad Power ™ ® OILOMATIC Quiet Line ™ MS 251, MS 251 C...
Page 129
TapAction ™ TrimCut ™ Esta lista de marcas comerciales está sujeta a cambios. Queda terminantemente prohibido todo uso de estas marcas comerciales sin el consentimiento expreso por escrito de ANDREAS STIHL AG & Co. KG, Waiblingen. MS 251, MS 251 C...
Page 132
California son considerados como causantes de of California to cause cancer, birth cáncer, defectos de nacimiento u otros efectos defects or other reproductive harm. nocivos para los órganos de la reproducción. 0458-737-8621-B englisch / spanisch USA englisch / spanisch USA www.stihl.com *04587378621B* 0458-737-8621-B...
Need help?
Do you have a question about the MS 251 and is the answer not in the manual?
Questions and answers
I do not have spark on my MS251C. Just died after 1 pull.
Possible causes for a Stihl MS 251C having no spark after one pull include:
1. Faulty Spark Plug – Even if it looks fine, the spark plug may be defective or fouled. Try replacing it.
2. Disconnected or Damaged Ignition Wire – Check if the ignition wire is securely connected and not damaged.
3. Ignition Coil Failure – A faulty ignition coil can prevent spark generation.
4. Kill Switch Malfunction – Ensure the kill switch is in the correct position and not shorting the ignition circuit.
5. Flywheel Magnet Misalignment – If the flywheel magnets are misaligned or dirty, they may not generate spark properly.
6. Grounding Issue – A short circuit in the wiring could be grounding the ignition system, preventing a spark.
Inspect these components systematically to diagnose and resolve the issue.
This answer is automatically generated