Related Manuals for Cadac STRATOS 98721
Summary of Contents for Cadac STRATOS 98721
- Page 1 USER INSTRUCTIONS STRATOS 2 BURNER mOdEL No’s 98721, 98723 LIVE THE BRAAI LIFE 503-0314 LEV8...
- Page 2 CAUTION For Outdoor use only! This appliance may not be used in an exterior enclosed balcony, porch or entertainment area! IMPORTANT Read these instructions for use carefully so as to familiarize yourself with the appliance before connecting it to its gas container. Keep these instructions for future reference 1.
-
Page 3: Safety Information
• Keep gas cylinders away from heat and flames. Do not place on a stove Seal here or any other hot surface. • Ensure that the assembled unit is stable and does not rock. • Do not cover or change the primary air supply openings in the burners as this will affect the performance of the product and may lead to an Cylinder Valve unstable flame. • In the event of burn back, (where the flame burns back and ignites at the jet), immediately turn off the gas supply by first closing the control Fig. 1 valve on the gas cylinder and then the appliance valve. After the flame is extinguished remove the regulator and check the condition of its seal. Replace the seal if in doubt. Re-light the appliance as described in Section 3 below. Should the flame light back persistently return the product to your authorized CADAC repair agent. • If there is a leak on your appliance (smell of gas), immediately close the control knob on the gas cylinder. If you wish to check for leaks on your appliance, do it outside. Do not try to detect leaks using a flame; use soapy water. • The correct way is to smear the joints with soapy water. If a bubble or bubbles form then there is a gas leak. Immediately turn off the gas supply firstly by closing the control valve on the gas container and then the appliance valve. Check that all the connections are properly fitted. Re-check with soapy water. If a gas leak persists, return the product to your CADAC dealer for inspection / repair. • Do not modify the appliance or use it for anything which it has not been Fig. 2 designed for. • During use, part of the appliance will become hot, particularly the cooking areas and the hood. Avoid touching hot parts with your bare hands. The use of oven gloves is recommended. -
Page 4: Using The Appliance
• When changing a gas cylinder, first close the cylinder valve and then the appliance valve, making sure the flame is extinguished and unscrew the regulator. Re-fit the regulator to a full cylinder following the same precautions as described above. • After the appliance has been fully assembled, perform a gas leak test before operating the appliance. 5. General Maintenance • There are no predetermined maintenance intervals for this appliance. • It is dangerous to use an appliance with a cracked or perished seal and/or hose. Inspect both seals and hose regularly and replace if they are not in order before using the appliance. • If the appliance was in use it will be hot. Allow to cool sufficiently before attempting any maintenance. • CADAC Patio BBQ’s are fitted with spesific CADAC jets to regulate the correct amount of gas. Should the hole in the Jet become blocked it may result in a small flame or no flame at all. Do not attempt to clean the Jet with a pin or other such device as this may damage the hole, which could make the appliance unsafe. Refer to “Introduction“ (Section 1) for jet sizes. 5.1.Replacing a Blocked Jet • Ensure that the cylinder valve is closed, then disconnect the appliance from the gas cylinder. • Remove the grill plates. Remove the flame tamers to expose the burners. Remove the retaining screws of the affected burner. • Remove the affected burner by lifting it out of its location taking care not to damage the control valve whilst doing so. This will expose the Jet. • Unscrew the blocked Jet with a suitable spanner and replace it with a new Jet. Do not use pliers on the Jet as they can cause damage, making the Jet unusable or impossible to remove. • To re-assemble, reverse the above procedure. Do not over tighten as this may damage the Jet. 5.2.Replacement of Hose • The hose length should not be less than 0.8m or exceed 1.2m. Check the expiry date on the hose and replace when necessary. Fitting... -
Page 5: Troubleshooting
• To repair minor tea staining or pitting, you can use a light, non-metallic scourer. It is important that you rub with the natural grain of the stainless steel surface to avoid leaving visible scratch marks. • Between uses, it is a good idea to leave the barbeque covered to prevent dust and air borne salts settling on the stainless steel surfaces. • With a small amount of care, your investment in quality stainless steel will keep its beautiful finish as well as its value for a long time to come. 8. Storage • Handle the appliance with care. Do not drop it. • After use, wait until the appliance has cooled down, disconnect it from the gas cylinder and store in a cool dry place away from heat. • Keep the dome closed when not in use to prevent dirt and insects falling into the unit, which may affect the gas flow. • Use a CADAC BBQ cover, especially if the unit is stored outdoors. • Before every use, ensure that the burners and venturies are free of insects, dust and spider webs. 9. Spares and Accessories • Always use genuine CADAC spares as they have been designed to give optimum performance. Description Part No. Jet No. 0.92 (28/37mBar) / (2.8kPa - SA Only) 0.92 Jet No. 0.81 (50mBar) 0.81 Jet N0. 0.88 (Side Burner) (28/37mBar) / (2.8kPa - SA Only) 0.88 Jet N0. 0.75 (Side Burner) (50mBar) 0.75... - Page 6 10. Returning the Appliance for Repair or Service • Do not modify the appliance. This may cause the appliance to become unsafe. • Any modifications will render the CADAC (Pty) Ltd warranty null and void. • If you cannot rectify any fault by following these instructions, contact your local CADAC stockist for inspection and/or repair. 11. Warranty • CADAC (Pty) Ltd hereby warrants to the ORIGINAL PURCHASER of this CADAC Gas Barbecue, that it will be free of defects in material and workmanship from the date of purchase as follows: Valves: 5 Years Plastic parts: No Warranty Enamel parts (Except Flame Tamers): 5 Years Cast Iron: 5 Years Painted Frames: 1 Year Stainless Steel Burners: 2 Years Enamel Flame Tamers: 2 Years The warranty will only apply if the unit is assembled and operated in accordance with the printed instructions.
- Page 7 LIVE THE BRAAI LIFE...