6 x 3 matrix switcher for composite video / s-video and stereo audio (24 pages)
Summary of Contents for Inline HR series
Page 1
Operation Manual Pathfinder HR Series High Resolution RGB Matrix Switchers...
Page 2
Installation and Safety Instructions For Models without a Power Switch: The socket outlet shall be installed near the equipment and shall be accessible. For Models with 110 / 220V Power Selector: Caution: Before applying power to this unit, the voltage selector must be set to the appropriate setting to match local A/C line voltage.
Page 3
Installations und Sicherheitshinweise Für Geräte ohne Netzschalter: Die Netzsteckdose soll in de Nähe des Gerätes installiert und frei zugänglich sein. Für Geräte mit 110 / 220V Spannungswähler: Achtung: Bevor Sie dem Gerät Spann ung zuführen, muß der Spannungswähler entsprechend der Spannung des lokalen Wechselspannungsnetzes eingestellt werden.
Page 4
CE COMPLIANCE All products exported to Europe by Inline, Inc. after January 1, 1997 have been tested and found to comply with EU Council Directive 89/336/EEC. These devices conform to the following standards: EN50081-1 (1991), EN55022 (1987) EN50082-1 (1992 and 1994), EN60950-92...
Remote Control Only (Disable Front Panel) ..............18 System Information......................18 Serial Control Operations......................19 Using RS-232 Control.......................19 Communication Protocol ....................19 Baud Rate Selection......................19 Command Code Structure....................20 Controlling Multiple Inline Products ................21 Control Port Pin-Outs .......................21 Serial Command List ......................22 Specifications..........................23 Warranty ...........................24...
PATHFINDER HR VARIETIES The PATHFINDER HR series includes several different models, all of which are housed in a rack mountable case measuring 3U in height. The front panel is identical on all models while the rear panel layout, switching boards and model designations vary according to the following...
FIXED VS. RECONFIGURABLE PATHFINDER HR matrices are manufactured in two basic varieties: Fixed and Reconfigurable. Before installing or operating a PATHFINDER HR series switcher, it is important to understand the differences between fixed and reconfigurable matrices. Fixed matrix models have a factory set number of available inputs and outputs. Some users might also call this type of matrix switcher a “conventional matrix,”...
UICK NSTALL The section provides a quick overview to help you get the PATHFINDER HR series switcher up and running in a hurry. Each subject and procedure is covered in greater detail in the remainder of this manual including images of all LCD screen displays.
WITCHING PERATIONS The Pathfinder HR series matrix switcher is capable of routing any input to any output or multiple outputs. The unit’s switching operations may be controlled from either the front panel or through the serial port. Front panel switching operations are accomplished using the Path Mapping Display as described below or by saving and recalling configuration memories.
CONFIGURATION MEMORIES HR Series Pathfinders feature ten configuration memories. These store all input / output patches for all board groups. By storing commonly used configurations it is easy to recall them using either the front panel or a very simple serial command.
PERATIONS USING RS-232 CONTROL The PATHFINDER HR series switchers include an 9-pin REMOTE CONTROL port which will accept serial commands from a control system, computer serial port, or any other device capable of sending out serial ASCII commands at compatible baud rates. All switching, mode selection (except Recall Mode), and set-up parameters can be controlled using RS-232 commands.
INLINE products can be set to recognize one of four sets of leading codes and ending codes. These are: [ ] { } ( ) < > . The factory default for leading / ending codes is [ ].
By setting each unit to a different command code pair, up to four different INLINE products can be controlled by a single RS-232 serial control port. Once a unit is set to look for a certain pair of leading and ending delimiters (command codes), it will ignore all other commands sent by the port.
INLINE warrants the equipment it manufactures to be free from defects in materials and workmanship. ♦ If equipment fails because of such defects and INLINE is notified within two (2) years from the date of shipment, INLINE will, at its option, repair or replace the equipment at its plant, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.