Compact disc stereo radio cassette recorder (23 pages)
Summary of Contents for Aiwa CSD-FD71 U
Page 1
CSD-FD71 CSD-FD73 K,EZ SERVICE MANUAL COMPACT DISC STEREO BASIC TAPE MECHANISM : TN-21ZVC-2000 CASSETTE RECORDER BASIC CD MECHANISM : CMS-B31TG6 • This Service Manual is the "Revision Publishing" and replaces "Simple Manual", (S/M Code No. 09-001-425-4T1). • If requiring information about the CD mechanism, see Service Manual of CMS-B31TG6, (S/M Code No.
SPECIFICATIONS Tuner section General Frequency range Speaker 100 mm cone type (2), 60 mm cone type (2) FM : 87.5 MHz - 108 MHz Output Headphones jack (stereo mini-jack) Antenna : Rod antenna Power output AM<U> : 530 / 531 kHz - 1,710 / 1,602 kHz 2.5 W + 2.5 W (EIAJ 7 ohms DC) (10/9 kHz/step) K, EZ :...
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
TRANSISTOR ILLUSTRATION E C B B C E E C B 2SA933SRS 2SB1370E 2SA1296GR 2SA1162Y 2SA933RS 2SC1815Y 2SC2712GR 2SC1740S 2SC2714 2SC1740SR DTC114TK DTC114TS DTC114YK DTC124XS DTC144EK E C B 2SA1318 CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure Resistor Code Value of resistor Chip resistor Dimensions (mm)
Page 21
IC DESCRIPTION IC, LC867132V-5G68 Pin No. Pin Name Description O-RMC / CE CD read/write control output and TU CE. O-DATA Data output to M61509FP. O-CLK Output to LC72121M CLK. Not used. O-CLKSFT Clock shift output of the microcomputer. I-HOLD Hold status detection. I-RST Microcomputer reset pin.
Page 22
Pin No. Pin Name Description 51~54 S20~S23 LCD segment output. (not used) O-CD LED LED ON/OFF control output for CD functions. O-TU LED LED ON/OFF control output for TUNER functions. O-TA LED LED ON / OFF control output for TAPE function (not used) O-ROCK LED LED ON/OFF control output for ROCK.
Page 23
IC, LC78622ED Pin No. Pin Name Description DEFI Defect detection signal (DEF) input. Test input. A pull-down resistor is built in. Must be connected to 0V. External VCO control phase comparator output. VVSS – Internal VCO ground. Must be connected to 0V. ISET PDO output current adjustment resistor connection.
Page 24
Pin No. Pin Name Description LVSS – Left channel one-bit D/A converter ground. Must be connected to 0V. RVSS Right channel one-bit D/A converter ground. (Must be connected to 0V.) RCHO Right channel onr-bit D/A converter output. RVDD Right channel one-bit D/A converter power supply. MUTER Right channel one-bit D/A converter mute output.
Page 25
IC, LA9241ML Pin No. Pin Name Description For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF FIN2 signal and subtraction from it create an EF signal. FIN1 For the connection of the pickup photodiode. For the connection of the pickup photodiode.
Page 26
Pin No. Pin Name Description The HFL (high frequency level) signal is used to judge whether the main beam is positioned on the pit or on the mirror. SLOF Sled servo off control input. CLV error signal input from the DSP. RFSM RF output.
TAPE MECHANISM PARTS LIST 1 / 1 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 1 S1-921-030-4A0 HEAD BASE 36 S1-921-140-030 REC BUTTON LEVER 2 S1-821-030-070 AZIMUTH SPRING 37 S1-921-140-170 P.S.LEVER SPRING 3 S1-921-030-090 PANEL P SPRING 38 S1-921-073-040 RF CLUTCH ASSY 4 S1-921-260-050...
Page 32
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9630469 0251431 Printed in Singapore...