Bosch GWS PROFESSIONAL Original Instructions Manual page 19

OBJ_BUCH-777-009.book Page 20 Monday, August 5, 2013 11:15 AM
20 | English
Angle Grinder
Thread length (max.) of grinder spindle
Restarting Protection
Reduced starting current
Weight according to EPTA-Procedure 01/2003
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
21.06.2013
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance for addresses, see section "After-
sales Service and Application Service".
Protection Guard for Grinding
Place the protection guard 5 on the spindle collar. Adjust the
position of the protection guard 5 to the requirements of the
operation and lock the protection guard 5 with the locking
screw 6.
 Adjust the protection guard 5 in such a manner that
sparking is prevented in the direction of the operator.
Protection Guard for Cutting
 For cutting with bonded abrasives, always use the pro-
tection guard for cutting 13.
1 609 92A 0B8 | (5.8.13)
GWS ... 24-180 24-230
JH H
mm 25 25

–

–
kg 5.1 5.2
kg 5.0 5.1
/II /II
 Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 13 is mounted in the same
manner as the protection guard for grinding 5.
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard 24 is
mounted in the same manner as the protection guard for
grinding 5.
Auxiliary Handle
 Operate your machine only with the auxiliary handle 3.
Screw the auxiliary handle 3 on the right or left of the machine
head depending on the working method.
Hand Guard
 For operations with the rubber sanding plate 20 or with
the cup brush/wheel brush/flap disc, always mount the
hand guard 18.
The hand guard 18 is fastened with the auxiliary handle 3.
Mounting the Grinding Tools
 Before any work on the machine itself, pull the mains
plug.
 Do not touch grinding and cutting discs before they
have cooled down. The discs can become very hot while
working.
Clean the grinder spindle 4 and all parts to be mounted.
For clamping and loosening the grinding tools, lock the grind-
er spindle with the spindle lock button 1.
 Actuate the spindle lock button only when the grinder
spindle is at a standstill. Otherwise, the machine may be-
come damaged.
Grinding/Cutting Disc
Pay attention to the dimensions of the grinding tools. The
mounting hole diameter must fit the mounting flange without
play. Do not use reducers or adapters.
When using diamond cutting discs, pay attention that the di-
rection-of-rotation arrow on the diamond cutting disc and the
direction of rotation of the machine (see direction-of-rotation
arrow on the machine head) agree.
See graphics page for the mounting sequence.
24-230 26-180 26-230
JH JH JH
25 25 25
  
  
5.3 6.0 6.1
5.2 5.9 6.0
/II /II /II
Bosch Power Tools