Teleste EOC04 Install And Operation Instructions
  1. Manuals
  2. Brands
  3. Teleste Manuals
  4. Extender
  5. EOC04
  6. Install and operation instructions

Teleste EOC04 Install And Operation Instructions

Ethernet over coax wi-fi extender
Hide thumbs

Advertisement

Table of Contents

EOC04 Ethernet over
Coax Wi-Fi extender
Setup and applications guide
Install and applications guide
Sections
2
3
4
5
6
7
8
9
11
19

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EOC04 and is the answer not in the manual?

Questions and answers

Related Manuals for Teleste EOC04

Summary of Contents for Teleste EOC04

  • Page 1: Table Of Contents

    EOC04 Ethernet over Coax Wi-Fi extender Setup and applications guide Install and applications guide Sections What’s in the box Product overview Connectivity Set up options Wi-Fi & Ethernet extension using existing Cable TV wiring Wi-Fi & Ethernet extension using existing DVB -T (TV aerial) cabling...

  • Page 2: What's In The Box

    What’s in the box? 1 x EOC04 Wi-Fi Extender 2 x Wi-Fi aerials 1 x PSU 1 x Ethernet Patch cord 1 x Coax fly lead 1 x F to IEC adapter 1 x Quick start Guide...

  • Page 3: Product Overview

    Product overview Wi-Fi Aerials Reset button WPS indicator WiFi Status Local Ethernet Connection (Flashing green = active) Green = Gigabit Connection Red = 100 Base-T connection WPS connect Power (Red = on) Ethernet over coax Connection (Yellow = connected) TV ONLY OUTPUT to TV or Set top Box Wi-Fi Aerial (does not carry Ethernet signal)

  • Page 4: Connectivity

    Connectivity Loop out connection Attach Wi-Fi Attach Wi-Fi Goes to TV or Set top antennas here antennas here box RF IN connector Ethernet connection To Smart TV or IP Device Connect from RF Wall outlet to Cable in connector on EOC-04...

  • Page 5: Set Up Options

    Set up options The EOC04 is a multi-purpose Ethernet over coax bridge device. It can be used in a number of different ways to deliver Gigabit Ethernet and 2 Channel Wi-Fi via a Coax ( TV aerial or Cable TV) connection.

  • Page 6: Wi-Fi & Ethernet Extension Using Existing Cable Tv Wiring

    OUTPUT port of the amplifier, as the Ethernet over coax signal cannot pass through the amplifier. At the EOC04 Wi-Fi extender, connect the ‘CABLE IN’ socket to the wall outlet. Use the supplied COAX fly lead to then remake the connection to the TV or set top box, so that the signal is passing through the EOC04.

  • Page 7: Wi-Fi & Ethernet Extension Using Existing Dvb -T (Tv Aerial) Cabling

    Ethernet over coax signal cannot pass through the amplifier. At the EOC04 Wi-Fi extender, connect the ‘CABLE IN’ socket to the wall outlet. Use the supplied COAX fly lead to then make a connection to the TV or set top box, so that the signal is passing through the EOC04 to the TV or set top box.

  • Page 8: Setup And Configuration Procedure Cable Tv Wiring

    (see parts list Page 2) 3. Make a connection from the ‘ LOOP OUT’ port on the back of the EOC04 to the TV or Set top box - this enables the TV signal to still pass to the TV or Set top box.

  • Page 9: Wi-Fi Ssid And Password Setup

    This is done by using the simple Web browser interface built into the EOC-04 and a Laptop or Tablet computer. 1. When EOC04 is connected to coax network - Red power light + Yellow coax data light. Open a blank we browser on a laptop or tablet that is connected to the main Wi-Fi Router 2.
  • Page 10 If the following message appears, Refer to Page 11 How to change the IP address of the EOC-04 This indicates that the default IP address range of your main router (usually supplied by your ISP) is in a different range to the IP address of the EOC-04 For Example The default IP address of an EOC-04 is 192.168.1.155 But the Router is in a different range –...

  • Page 11: How To Change The Ip Address Of An Eoc-04

    1 x EOC on the network with the same (default) IP address. You will need to follow this section to change the IP address of any additional EOC-04 adapters, before you add them to the network. 1. Make a connection from a Laptop to the EOC04, using the Ethernet cable provided in the accessory kit.
  • Page 12 2. Follow the stages shown below to access the ‘Network & sharing Centre in Windows Click here Click here...
  • Page 13 Click here Click here...
  • Page 14 Double click here Click here...
  • Page 15 Enter the IP address as shown Note: it must not be exactly the same as the EOC-02 When entered click the OK box Close all of the other boxes you have opened by clicking on the OK box Now go back to your web browser and enter 192.168.1.155 in to the address box at the top of the page...
  • Page 16 You will now see the setup screen of the EOC-02 Click on LAN Interface...
  • Page 17 Click on Apply changes Enter a new default The EOC04 will save IP address here the changes and e.g. 192.168.0.155 restart If you are unsure of the default IP range of your router it is normally on a sticker on the underside and shown as an IP address e.g. 192.168.0.1 Or contact your internet service provider for more details –...
  • Page 18 Finally Disconnect your laptop from the EOC-04 Re-connect the EOC-04 to the Coax network Ensure it is powered up and the coax connection light is showing (section 3) Open a web browser on a laptop or tablet connected to the in home network Enter the new Default IP address you gave the EOC-04 into the browser address bar You should now see the EOC-04 setup screen...

  • Page 19: Super User Menu

    SUPER USER menu. For advanced operation and configuration, your EOC-04 has a ‘Super user’ menu. This is only accessible by entering the Super User password which is - super Note: all in lower case Click apply...
  • Page 20 www.teleste.com...

Table of Contents