Advertisement
INSTALLATION / WARRANTY INSTRUCTIONS
INSTALLATION / WARRANTY INSTRUCTIONS
PRODUCT BRAND
PRODUCT BRAND
PRODUCT NAME / CODES
PRODUCT NAME / CODES
PLEASE READ THESE INSTALLATION INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR MAINTAINING THIS
EQUIPMENT. THE PRODUCT IS DESIGNED FOR INSTALLATION AND MAINTENANCE IN ACCORDANCE WITH
PLEASE READ THESE INSTALLATION INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR MAINTAINING THIS
RELEVANT AUSTRALIAN STANDARDS (AS3000) AND LOCAL REGULATIONS (WHERE APPLICABLE), BY AN
EQUIPMENT. THE PRODUCT IS DESIGNED FOR INSTALLATION AND MAINTENANCE IN ACCORDANCE WITH
AUTHORISED AND LICENCED ELECTRICIAN. THE INSTALLATION INSTRUCTIONS WERE CORRECT AT THE TIME OF PRINT.
RELEVANT AUSTRALIAN STANDARDS (AS3000) AND LOCAL REGULATIONS (WHERE APPLICABLE), BY AN
TO REFLECT CHANGES IN TECHNOLOGY AND AUSTRALIAN STANDARDS; GERARD LIGHTING RESERVES THE RIGHT TO AMEND
AUTHORISED AND LICENCED ELECTRICIAN. THE INSTALLATION INSTRUCTIONS WERE CORRECT AT THE TIME OF PRINT.
THE INSTRUCTIONS WITHOUT NOTICE. UPDATED GUIDELINES CAN BE FOUND ON THE RELEVANT BRAND WEB SITE.
TO REFLECT CHANGES IN TECHNOLOGY AND AUSTRALIAN STANDARDS; GERARD LIGHTING RESERVES THE RIGHT TO AMEND
IMPORTANT - THE PRODUCT MUST BE MAINTAINED AND OPERATED IN ACCORDANCE WITH THE MANUFACTURER'S
THE INSTRUCTIONS WITHOUT NOTICE. UPDATED GUIDELINES CAN BE FOUND ON THE RELEVANT BRAND WEB SITE.
INSTRUCTIONS, FAILURE TO DO SO MAY DAMAGE THE PRODUCT AND SERVICES. IT IS STRONGLY RECOMMENDED THAT THIS
IMPORTANT - THE PRODUCT MUST BE MAINTAINED AND OPERATED IN ACCORDANCE WITH THE MANUFACTURER'S
IMPORTANT NOTE BE COMMUNICATED TO THE OWNER AND OR OPERATOR OF THE INSTALLATION AT THE TIME OF SITE
INSTRUCTIONS, FAILURE TO DO SO MAY DAMAGE THE PRODUCT AND SERVICES. IT IS STRONGLY RECOMMENDED THAT THIS
COMMISSIONING. GOOD PRACTICE DOES NOT RECOMMEND THE 24/7 USE OF PRODUCTS WITHOUT THE APPLICATION OF
IMPORTANT NOTE BE COMMUNICATED TO THE OWNER AND OR OPERATOR OF THE INSTALLATION AT THE TIME OF SITE
SUITABLE SWITCH CYCLE INTERVALS. FURTHERMORE, WITH THE OMISSION OF NOMINATED SURVIVAL CURVES AND OR
COMMISSIONING. GOOD PRACTICE DOES NOT RECOMMEND THE 24/7 USE OF PRODUCTS WITHOUT THE APPLICATION OF
RECOMMENDED OPERATING HOURS, PRODUCT DESIGN EXPECTATIONS PROVIDE FOR A CONTINUAL DAILY USAGE OF 6 HOURS
SUITABLE SWITCH CYCLE INTERVALS. FURTHERMORE, WITH THE OMISSION OF NOMINATED SURVIVAL CURVES AND OR
FOR RESIDENTIAL APPLICATIONS AND A CONTINUAL DAILY USAGE OF 12 HOURS FOR COMMERCIAL AND INDUSTRIAL
RECOMMENDED OPERATING HOURS, PRODUCT DESIGN EXPECTATIONS PROVIDE FOR A CONTINUAL DAILY USAGE OF 6 HOURS
APPLICATIONS. ALL PRODUCTS MUST BE THOROUGHLY CLEANED ON A REGULAR BASIS AT INTERVALS THAT REFLECT IN THE
FOR RESIDENTIAL APPLICATIONS AND A CONTINUAL DAILY USAGE OF 12 HOURS FOR COMMERCIAL AND INDUSTRIAL
INSTALLATION ENVIRONMENT, ENSURING THE OPTICAL PERFORMANCE, TOGETHER WITH THE ELECTRICAL, MECHANICAL AND
APPLICATIONS. ALL PRODUCTS MUST BE THOROUGHLY CLEANED ON A REGULAR BASIS AT INTERVALS THAT REFLECT IN THE
STRUCTURAL INTEGRITY AS DESIGNED, IS MAINTAINED THROUGHOUT THE SERVICE LIFE OF THE PRODUCT.
INSTALLATION ENVIRONMENT, ENSURING THE OPTICAL PERFORMANCE, TOGETHER WITH THE ELECTRICAL, MECHANICAL AND
STRUCTURAL INTEGRITY AS DESIGNED, IS MAINTAINED THROUGHOUT THE SERVICE LIFE OF THE PRODUCT.
QR CODE
For the latest product online reference data,
1. PRODUCT SPECIFICATION:
PLACEMENT
simply install and activate a QR code
IF AVAILABLE
scanner application on your smartphone.
Product brand
For more information refer brand web.
Product weight
Type of Protection
IP Rating - for interior products, the IP rating nominated
1. PRODUCT SPECIFICATION:
is "from below the ceiling" unless specifically nominated.
Important – when installing electronic or HID lighting equipment, the installer must consider the In-rush start current (if any) as
Product brand
documented on the control gear identification label when selecting appropriate circuit controls or protective devices.
Type of Protection
Voltage
IP Rating - for interior products, the IP rating nominated
Current
is "from below the ceiling" unless specifically nominated.
Rated Minimum / Maximum Ambient Temperature
Nominal design Voltage
Suitable for direct mounting on flammable surfaces
Circuit wattage
Dimmable
Line current
Installation orientation
Important – when installing electronic or HID lighting equipment, the installer must consider the In-rush start current (if any) as
Designed application
documented on the control gear identification label when selecting appropriate circuit controls or protective devices.
Rated average design life
Power factor
Minimum distance from lit objects
Nominal Freq. (Hz)
Rated Minimum / Maximum Ambient Temperature
2. APPROVALS: The RCM marking of this product applies to AS/NZS CISPR15 (EMC) "Limits and methods of
Suitable for direct mounting on flammable surfaces
measurement of radio disturbance characteristics of electrical lighting and similar equipment". This
Dimmable (if relevant refer brand web for approved list)
product is designed to conform to AS/NZS60598.1:2013 "Luminaires, general requirements and tests",
Installation orientation
AS/NZS60598.2.5:2002"Luminaires - Particular requirements – Floodlights"
Designed application
Rated average design life
3. STORAGE: Prior to installation products are to be stored in cool and dry conditions.
2. APPROVALS: The RCM marking of this product applies to AS/NZS CISPR15 (EMC) "Limits and methods of
4. APPLICATION: The installation application and orientation of the product is designed in accordance with the nominated
measurement of radio disturbance characteristics of electrical lighting and similar equipment". This
product IP rating, class designation and these installation instructions. Installation environments and operating conditions
product is designed to conform to AS/NZS60598 "Luminaires, general requirements and tests".
beyond these instructions are not recommended.
3. STORAGE: Prior to installation products are to be stored in cool and dry conditions.
5. INSTALLATION / GENERAL: Installation of the product is to be completed by an authorized and licensed electrician, in
accordance with these instructions, relevant Australia standards and local regulations (where applicable). Termination of product
4. APPLICATION: The installation application and orientation of the product is designed in accordance with the nominated
wiring, together with the installation of the product must be in a manner and orientation that maintains the integrity of the
product IP rating, class designation and these installation instructions. Installation environments and operating conditions
designated IP rating of the product For electronic control equipment (when supplied) DO NOT MEGGER between A and N.
beyond these instructions are not recommended.
6. INSTALLATION / SPECIAL CONDITIONS (relevant only for products approved for such an installation):
5. INSTALLATION / GENERAL: Installation of the product is to be completed by an authorized and licensed electrician, in
accordance with these instructions, relevant Australia standards and local regulations (where applicable). Termination of product
(a) products installed in high wind environments must have suitable installation / fastening methods applied to ensure the
wiring, together with the installation of the product must be in a manner and orientation that maintains the integrity of the
product's mounting points are not damaged through, corrosion, constant vibration and or movement. Exterior products are
designated IP rating of the product For electronic control equipment (when supplied) DO NOT MEGGER between A and N.
designed with precise vertical aiming limits, which should not be exceeded. Any vertical floodlight aiming requirements should
PAGE 1 OF 2
PAGE 1 OF 2
Page 2
- Sylvania
- Sylvania
- Sylvania Briteline LED Raptor – SR4H757A2
- Sylvania Briteline LED Raptor – SR4H757A2
Luminaire head only – Control gear refer additional instruction manual
COPYRIGHT GERARD LIGHTING
COPYRIGHT GERARD LIGHTING
Gerard Lighting Pty Ltd
96-112 Gow Street, Padstow, NSW 2211
Gerard Lighting Pty Ltd
T: 02 9794 9300 |
96-112 Gow Street, Padstow, NSW 2211
T: 02 9794 9300 |
- Sylvania
- 28.6Kgs
- Class I
240V System
415V System
- IP66
- Sylvania
-Sylvania
- Class I
- Class I
- 130 – 150V DC per channel
- 2.1 - 2.2A per channel
- IP66
- IP66
- 0°C / 40°C
- 240V
- 415V
- NO
- 1260W
- 1260W
- Refer compatible control gear
- 5.5A,
- 3.2A
- -10 deg to +60 deg on the horizontal refer page 5
- Exterior use only: Refer Section 6A
- 36000hrs @ L90
- 0.9
-0.9
- 5m
- 50 Hz
-050Hz
- -10°C / 40°C
- -10°C / 40°C
- NO
- NO
- YES 0-10V Analogue
- YES 0-10V Analogue
- -10 deg to +60 deg on the horizontal
- Exterior use, Insterior on GL approval
- 36000hrs @ L90
ABN 71 115 184 999
ABN 71 115 184 999
www.gerardlighting.com.au
www.gerardlighting.com.au
issue date: 01/04/2016
issue date: 01/04/2016
Vi2015
Vi2015
Advertisement
