Related Manuals for Daviscomms MTD1000
Summary of Contents for Daviscomms MTD1000
- Page 1 500206R01 MTD1000 ersonal racking ystem Start up Guide...
- Page 2 The receiver component required to receive GPS data to the MTD1000 device for a location fix. GPS active antenna d. Li- Polymer battery for MTD1000 An alternative solution to power up the MTD1000 without a power adaptor up to 24 hours. Voltage/ current specification: (3.7V/ 780mAh) Li-Polymer battery e.
- Page 3 500206R01...
- Page 4 500206R01 Setup 1. Determine if you have the RS232 port available on your PC 2. Setting up as a tracking device 3. Installation of Microsoft.NET ver 1.1 4. Installation steps for MTS application 5. Setting up as a modem 6. Google Earth Plus installation 7.
- Page 5 Connect the USB-Serial converter cable to the communications cable as in Fig.3 Important*: Download the ATEN serial-to USB converter cable driver from www.daviscomms.com.sg Please refer to steps below to install the ATEN USB-Serial driver to your PC. Step 1...
- Page 6 500206R01 Step 4 Step 3 Select “Search for the best driver in these locations” and check on “Include this location in the search”. Click “Browse” Locate the folder “Winxp V1.5” and click “OK” Step 5 Step 6 Click “Next” Click “Continue Anyway”...
- Page 7 MANAGER/PORTS to detect the comport number of the ATENS USB driver installed in your computer. Take note of the USB comport number for easy reference later. www.daviscomms.com.sg download Microsoft.Net Framework 1.1. Refer to page 8 for installation of Microsoft.NET program.
- Page 8 Select “I agree” and click “Install”. Step 5 Step 6 Click “OK” to complete the installation of the program. Important*: Download and install the MTD1000 PTS 3.00 application from www.daviscomms.com.sg Proceed to next page Please while your computer installs the program.
- Page 9 500206R01 5. Setup and installation steps for PTS application Step 1 Download and install the PTS application the application to your PC Step 2 Step 3 Back to setup Click “Next” Click “Next” Step 4 Step 5 Click “Next” Click “Next”...
- Page 10 500206R01 Step 6 Step 7 Click “Install” Please wait while Setup installs the program. Step 8 Step 9 Check “Launch MTD1000 PTS 3.00” and click “Finish” Select “Device” and click on “Serial port”...
- Page 11 500206R01 Step 10 Step 11 Key in the comport number of the e.g. COM1 if using the serial communications cable. Refer to page 7 step 9 if using the ATEN Serial to USB cable converter to find out the comport number.
- Page 12 *Important: Take note of the SIM card number of the modem Purchase the Google earth plus license key from https://registration.keyhole.com/choice_lt_initial.html Download Google earth from www.daviscomms.com.sg to your PC 6. Google Earth Plus installation Step 1 Step 2 Click “Run” to install the Google Earth installation program.
- Page 13 500206R01 Step 3 Step 4 Please wait while your computer prepares to installs the program Uncheck all boxes except launch “Google Earth” and click “Finish” to complete the installation. Important*: When Google earth is launched, go to Help-> Google Earth Plus License and enter the license key which you have already purchased online from step 31 and click activate.
- Page 14 Key in the phone number of the tracking device e.g. The Google Earth Plus application will appear on the desktop to “912345678” display the location of the tracking device. Click on “Add” For more information please visit www.daviscomms.com.sg Click “SMS channel” under “communications...
- Page 15 500206R01 Appendix LEDs status indication of the tracking device and modem When the red LED is lighted up, it means the unit is charging up the Li-polymer battery When the red LED is not lighted up, it means the Lithium polymer battery is fully charged or the Li- polymer battery is not connected to the battery and charging is not active.