Summary of Contents for PCM PCM-5820 Series
- Page 1 PCM-5820 Series (PCM-5820/5820L/5820E/5822) NS GXM Single Board Computer with CPU SVGA/LCD, Ethernet, Audio and TV-out Interface...
-
Page 2: Copyright Notice
For technical support and service for please visit our support website. This manual is for the PCM-5820/5820L Rev. A103 or higher. PCM-5820E Rev. A101 or higher, PCM-5822 Rev. A101 Part No. 2006582003 3rd Edition Printed in Taiwan December 1999... -
Page 3: Packing List
Packing list Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCM-5820 Series all-in-one single board computer • 1 startup manual • 1 utility disk/CD, driver, and manual (in PDF format) •... -
Page 4: Table Of Contents
1.3.2 Local-bus flat panel/VGA interface ...... 5 1.3.3 LVDS (Low Voltage Differential Signal) interface..............5 1.3.4 Audio function ............5 1.3.5 Ethernet interface (PCM-5820/5820E only) ..5 1.3.6 Mechanical and environmental ......6 1.3.7 Solid state disk ............6 Board layout and dimensions ........7 Chapter 2 Installation ........9... - Page 5 2.12 Power connectors ............22 2.12.1 Main power connector +5 V, +12 V (CN9) ..22 2.12.2 Auxilary power connector (CN10) ....22 2.12.3 CPU fan power connector (CN6) ...... 22 2.13 IR connector (CN7) ............ 22 2.14 Audio interfaces (CN5, CN1) ........23 2.14.1 Audio connector (CN5) ........
- Page 6 (800 x 600 TFT color LCD) ........ 36 Ethernet interface configuration ......37 Chapter 4 Award BIOS Setup ......... 39 System test and initialization ........40 4.1.1 System configuration verification ....... 40 Award BIOS setup ............. 41 4.2.1 Entering setup ............. 41 4.2.2 Standard CMOS setup .........
- Page 7 Installation of audio driver ........64 6.2.1 Installation for Windows 95/98 ......65 6.2.2 Installation for Windows NT ......68 Chapter 7 PCI Bus Ethernet Interface ....71 Introduction ..............72 Installation of Ethernet driver ........72 7.2.1 Installation for MS-DOS and Windows 3.1 ..72 7.2.2 Installation for Windows 95/98 ......
- Page 8 Appendix B System Assignments ......91 System I/O ports ............92 DMA channel assignments ........93 Interrupt assignments ..........94 1st MB memory map ..........95 Appendix C LCD Services ........97 LCD Services .............. 98 Appendix D Installing PC/104 Modules ....99 Installing PC/104 modules ........
- Page 9 Tables Table 2-1: Jumpers ....................10 Table 2-2: Connectors ..................... 11 Table 2-3: Audio power source setting ..............23 Table 2-4: COM2 selection (J4) ................24 Table 2-5: Serial port default settings ..............24 Table 2-6: LCD power setting ................. 26 Table 2-7: Ethernet LED setup ................
- Page 10 Figure 2-3: Connectors - solder side ............14 Figure 2-4: Jumper settings ..............16 Figure 3-1: Contents of the PCM-5820 Series utility disk ......31 Figure 3-2: BIOS VGA setup screen ............33 Figure 4-1: BIOS setup program initial screen ........41 Figure 4-2: CMOS setup screen ..............
-
Page 11: Chapter 1 General Information
General Information This chapter gives background informa- tion on the PCM-5820 Series. Sections include: • Board specifications • Board layout and dimensions... -
Page 12: Introduction
You can change the display BIOS simply by programming the Flash chip. If you need any additional functions, the PCM-5820 Series has a PC/104 connector for future upgrades. PCM-5820 Series User's Manual... -
Page 13: Features
• On-board LVDS interface (PCM-5820L and PCM-5820E only) • On-board 100Base-T Ethernet interface (PCM-5820/5820E/ PCM-5822 only) • On-board TV-out function, NTSC and PAL format (PCM-5822) • Supports CompactFlash card • Built-in Enhanced IDE (AT bus) hard disk drive interface • On-board mini-DIN PS/2 keyboard/mouse connector •... -
Page 14: Specifications
Specifications 1.3.1 Standard SBC functions • CPU: - Embedded NS GXM-233 / 2.9 V (for PCM-5820/L) - Embedded NS GXM-200 / 2.2 V (for PCM-5820E/PCM- 5822) • BIOS: AWARD 256 KB Flash memory • Chipset: NS CX5530 • System memory: One 144-pin SODIMM socket accepts up to 128 MB SDRAM •... -
Page 15: Local-Bus Flat Panel/Vga Interface
• Audio interface: Microphone in, Line in, CD audio in, Line out, Speaker L, Speaker R. • Power: Accepts +12 V source for improved audio quality 1.3.5 Ethernet interface (PCM-5820/5820E/5822 only) • Chipset: RTL 8139 • Ethernet interface: PCI 10/100 Mbps Ethernet. IEEE 802.3 u protocol compatible •... -
Page 16: Mechanical And Environmental
• Weight: 0.77 kg (weight of total package) 1.3.7 Solid state disk • Supports one 50-pin socket for CompactFlash™ card 1.3.8 TV-out function (PCM-5822 only) • Chipset: CHRONTEL CH7003C • Supports NTSC, NTSC-EIA (Japan) and PAL TV formats • Provides Composite, S-video, and SCART (optional) outputs via RCA (composite) connector and S-video connector •... -
Page 17: Board Layout And Dimensions
Board layout and dimensions Figure 1-1: PCM-5820 Series dimensions Chapter 1 General Information... - Page 18 PCM-5820 Series User's Manual...
-
Page 19: Chapter 2 Installation
Installation This chapter tells how to set up the PCM-5820 Series hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installa- tion procedure. -
Page 20: Jumpers And Connectors
The table below lists the function of each of the board jumpers and connectors: Table 2-1: Jumpers Label Function Audio power source setting Clear CMOS Watchdog timer action COM2 selector Buzzer setting LCD power selector Ethernet power select (PCM-5822) PCM-5820 Series User's Manual... -
Page 21: Table 2-2: Connectors
CRT display connector CN19 CompactFlash socket CN20 SODIMM socket CN21 RCA (composite) connector (PCM-5822 only) CN22 S-Video connector (PCM-5822 only) CN23 ATX feature connector (PCM-5822) CN24 ATX power button & power LED connector LED1 Ethernet LED (PCM-5820/5820E/5822) LED2 Power & HDD LED... -
Page 22: Locating Jumpers
Locating jumpers Figure 2-1: Jumpers PCM-5820 Series User's Manual... -
Page 23: Locating Connectors
Locating connectors 2.3.1 Component side Figure 2-2a: Connectors - component side (PCM-5820/L/E) Figure 2-2b: Connectors - component side (PCM-5822) Chapter 2 Installation... -
Page 24: Solder Side
2.3.2 Solder side Figure 2-3: Connectors - solder side (PCM-5820 Series) PCM-5820 Series User's Manual... -
Page 25: Setting Jumpers
Setting jumpers 2.4.1 Introduction You may configure your card to match the needs of your applica- tion by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. -
Page 26: Settings Details
1 - 2 *1 - 2 *Closed Enable 2 - 3 3.3 V Open Disable J4: COM2 Selector Closed Result Pins *1 - 2 RS-232 3 - 4 RS-422 * default setting 5 - 6 RS-485 PCM-5820 Series User's Manual... -
Page 27: Safety Precautions
Safety precautions Warning! Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on because sensitive electronic components can be damaged by the sudden rush of power. Caution! Always ground yourself to remove any static charge before touching the board. -
Page 28: Installing Dram (Sodimms)
SODIMM sockets snap into place. 5. Check to ensure that the SODIMM is correctly seated and all connector contacts touch. The SODIMM should not move around in its socket. PCM-5820 Series User's Manual... -
Page 29: Ide Hard Drive Connector (Cn11)
Connecting drives is done in a daisy-chain fashion and requires one or two cables, depending on the drive size. All required cables are included in your PCM-5820 Series package. 1.8" and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector. 3.5"... -
Page 30: Compactflash Disk (Cn19)
PC system. Floppy drive connector (CN2) You can attach up to two floppy drives to the the PCM-5820 Series' on-board controller. Any combination of 5¼” (360 KB and 1.2 MB) and/or 3½” (720 KB, 1.44 MB, and 2.88 MB) drives is possible. -
Page 31: Parallel Port Connector (Cn3)
Appendix A. 2.10 Parallel port connector (CN3) Normally, the parallel port is used to connect the card to a printer. The PCM-5820 Series includes a multi-mode (ECP/EPP/SPP) parallel port, accessed through CN3 - a 26-pin flat-cable connec- tor. -
Page 32: Keyboard And Ps/2 Mouse Connector (Cn17)
POST. 2.12 Power connectors 2.12.1 Main power connector +5 V, +12 V (CN9) Supplies main power to the PCM-5820 Series (+5 V) and devices that require +12 V. 2.12.2 Auxilary power connector (CN10) Supplies secondary power to peripherals that require -5 V and -12 V. -
Page 33: Audio Interfaces (Cn5, Cn1)
CD-ROM drive is suitable for connection to CN1. 2.14.3 Audio power source setting (J1) The PCM-5820 Series is designed to work with a single +5 V power supply as audio interfaces usually function under +5 V. However, most audio controllers require an independant +12 V power source since this avoids noise interference from other digital circuits. -
Page 34: Serial Ports (Cn16, Cn14)
Chapter 6 for audio setup details. 2.15 Serial ports (CN16, CN14) The PCM-5820 Series offers two serial ports: one RS-232 and one RS-232/422/485. These ports allow you to connect to any serial device (a mouse, printers, etc.) or communication network. -
Page 35: Vga Interface Connections
Therefore make sure that CN9 is connect- ed to a +12 V power supply. The PCM-5820 Series provides a bias control signal on CN12 which can be used to control the LCD bias voltage. It is recom- mended that the LCD bias voltage not be applied to the panel until the logic supply voltage (+5 V or +3.3 V) and panel video signals... -
Page 36: Lcd Power Setting (J6)
2.16.3 LCD power setting (J6) The PCM-5820 Series' PCI SVGA interface supports 5 V and 3.3 V LCD displays. By changing the setting of J6, you can select the panel video signal level to be 5 V or 3.3 V. -
Page 37: Ethernet Interface Connections
2.18 Ethernet interface connections The PCM-5820 Series is equipped with a high performance 32-bit PCI Ethernet interface which is fully compliant with IEEE 802.3u 10/100 Mbps CSMA/CD standards. 2.18.1 100Base-T RJ-45 connector (CN13) 100Base-T connections are made via the on-board RJ-45 connec- tor. -
Page 38: Ethernet Led And Hdd/Power Leds
An on-board watchdog timer reduces the chance of disruptions which EMP (electro-magnetic pulse) interference can cause. This is an invaluable protective device for standalone or unmanned applications. Setup involves one jumper and running the control software (refer to Appendix C). PCM-5820 Series User's Manual... -
Page 39: Watchdog Timer Action (J3)
IRQ11 * default setting 2.21 USB connectors (CN4) The PCM-5820 Series board provides two USB (Universal Serial Bus) interfaces which gives complete Plug and Play, and hot swaps for up to 127 external devices. The USB interfaces comply with USB specification Rev. 1.0 and are fuse protected. -
Page 40: Atx Power Control Connector (Cn23,Cn24)
2.23 ATX power control conn. (CN23, CN24) The PCM-5820 Series offers two serial ports: one RS-232 and one RS-232/422/485. These ports allow you to connect to any serial device (a mouse, printers, etc.) or communication network. 2.23.1 ATX feature connector (CN23) and power... -
Page 41: Chapter 3 Software Configuration
Software Configuration This chapter details the software configu- ration information. It shows you how to configure the card to match your applica- tion requirements. Award system BIOS is covered in Chapter 4. Sections include: • LCD display configuration • Connections for two standard LCDs... -
Page 42: Introduction
BIOS simply by reprogramming the Flash chip. Utility CD disk The PCM-5820 Series is supplied with a software utility on CD-ROM. This disk contains the necessary file for setting up the VGA display. Directories and files on the disk are as follows: AWDFLASH.EXE... -
Page 43: Vga Display Software Configuration
Configure the LCD type as follows: 1. Apply power to the PCM-5820 Series with a color TFT display attached. This is the default setting for the PCM-5820 Series. - Page 44 Y. Press N to exit the program. The new VGA configuration will then write to the ROM BIOS chip. This configuration will remain the same until you run the AWDFLASH.EXE program and change the settings. PCM-5820 Series User's Manual...
-
Page 45: Connections For Two Standard Lcds
Connections for two standard LCDs 3.4.1 Connections for Toshiba LTM10C042 (640 x 480 TFT color LCD) Table 3-1: Connections for Toshiba LTM10C042 LTM10C042 PCM-5820 Series CN12 Name Name SHFCLK PD12 PD13 PD14 PD15 PD16 PD17 PD10 PD11 ENAB +5 V... -
Page 46: Connections For Toshiba Ltm12C275A
3.4.2 Connections for Toshiba LTM12C275A (800 x 600 TFT color LCD) Table 3-2: Connections for Toshiba LTM12C275A LTM12C275A PCM-5820 Series CN12 Name Name NCLK SHFCLK PD12 PD13 PD14 PD15 PD16 PD17 PD10 PD11 ENAB M/DE +5 V +5 V PCM-5820 Series User's Manual... -
Page 47: Ethernet Interface Configuration
1. Power the PCM-5820 Series on. Make sure that the RSET8139.EXE file is located in the working drive. 2. At the prompt, type RSET8139.EXE and press <Enter>. The Ethernet configuration program will then be displayed. - Page 48 PCM-5820 Series User's Manual...
-
Page 49: Chapter 4 Award Bios Setup
Award BIOS Setup This chapter describes how to set BIOS configuration data. -
Page 50: System Test And Initialization
3. The CMOS memory has lost power and the configuration information has been erased. The PCM-5820 Series' CMOS memory has an integral lithium battery backup. The battery backup should last ten years in normal service, but when it finally runs down, you will need to replace the complete unit. -
Page 51: Award Bios Setup
Award BIOS setup Award’s BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. 4.2.1 Entering setup Power on the computer and press <Del>... -
Page 52: Standard Cmos Setup
Once a field is highlighted, on-line help information is displayed in the left bottom of the Menu screen. Figure 4-2: CMOS setup screen PCM-5820 Series User's Manual... -
Page 53: Bios Features Setup
By choosing the BIOS FEATURES SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-5820 Series. Figure 4-3: BIOS features setup Chapter 4 Award BIOS Setup... -
Page 54: Chipset Features Setup
4.2.4 Chipset features setup By choosing the CHIPSET FEATURES SETUP option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-5820 Series. Figure 4-4: Chipset features setup PCM-5820 Series User's Manual... -
Page 55: Power Management Setup
By choosing the POWER MANAGEMENT SETUP option from the INITIAL SETUP SCREEN menu, the screen below is dis- played. This sample screen contains the manufacturer’s default values for the PCM-5820 Series. Figure 4-5: Power management setup Chapter 4 Award BIOS Setup... -
Page 56: Pnp/Pci Configuration
4.2.6 PnP/PCI configuration By choosing the PnP/PCI CONFIGURATION option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-5820 Series. Figure 4-6: PnP/PCI configuration PCM-5820 Series User's Manual... -
Page 57: Integrated Peripherals
INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’s default values for the PCM-5820 Series. The PANEL TYPE by default supports a 18-bit 640 x 480 TFT LCD panel display. Figure 4-7: Integrated peripherals... -
Page 58: Load Bios Defaults
LOAD BIOS DEFAULTS loads the default system values directly from ROM. If the stored record created by the Setup program becomes corrupted (and therefore unusable), these defaults will load automatically when you turn the PCM-5820 Series on. Confirm Password: Figure 4-8: Load BIOS defaults screen... -
Page 59: Change Password
4.2.9 Change password To change the password, choose the PASSWORD SETTING option form the Setup main menu and press <Enter>. 1. If the CMOS is bad or this option has never been used, a default password is stored in the ROM. The screen will display the following messages: Enter Password: Press <Enter>. -
Page 60: Auto Detect Hard Disk
This record is required for the system to operate. 4.2.12 Exit without saving Selecting this option and pressing <Enter> lets you exit the Setup program without recording any new values or changing old ones. PCM-5820 Series User's Manual... -
Page 61: Chapter 5 Svga Setup
SVGA Setup • Introduction • Installation of SVGA driver for Windows 95/98/NT... -
Page 62: Introduction
The PCM-5820 Series has an on-board LCD/VGA interface. The specifications and features are described as follows: 5.1.1 Chipset The PCM-5820 Series uses a Cyrix CX5530 chipset for its SVGA controller. It supports many popular 18-bit LCD displays and conventional analog CRT monitors. The VGA BIOS supports LCD. -
Page 63: Installation Of Svga Driver
Complete the following steps to install the SVGA driver. Follow the procedures in the flow chart that apply to the operating system that you are using within your PCM-5820 Series. Important: The following windows illustrations are examples only. You must follow the flow chart instructions and pay attention to the instructions which then appear on your screen. -
Page 64: Installation For Windows 3.1
C h o o s e t h e language you want to use during installation. a. Select the highlighted item. b. P r e s s " E N T E R " . a. Press "ENTER" to install all resolutions. PCM-5820 Series User's Manual... - Page 65 a. Type the path of the operating system. a. When installation is completed, reboot the system. b. You will see the "ChipsCPL" icon in the control panel. ChipsCPL a. Double click "ChipsCPL". b. Adjust screen size, color and refresh rate to your preferences.
-
Page 66: Installation For Windows 95/98
Choose the "Adapter" label. b. Press the "Change..." button. a. Press the "Have Disk" button. a. Insert the disc into the CD-ROM drive. b. T y p e "D:\5820\ "D:\VGA\Win95\". VGA.100\Win9X\VGA". c. Press "OK". D:\VGA\Win95\ D:\5820\VGA.100\Win9X\VGA\ PCM-5820 Series User's Manual... - Page 67 a. Select the highlighted item. b. Click the "OK" button. a. C & T 6 5 5 5 5 appears in the adapter label. b. Click the "Apply" button. a. Press "Yes" to reboot. a. Repeat Step 1 on the previous page of this manual.
- Page 68 Press "OK" to exit. a. Press "Yes" to set the monitor type. a. Select "Standard", "Super VGA 800 x 600", or "XGA". b. Press the "OK" button. a. Choose "Restart" to reboot. E N D PCM-5820 Series User's Manual...
-
Page 69: Installation For Windows Nt
5.2.3 Installation for Windows NT a. Select "Start", "Settings", "Control Panel". b. Double click the "Display" icon. a. Choose the "Settings" label. b. Press the "Display Type" button. a. Press the "Change..." button. a. Click the "Have Disk..." button. Chapter 5 SVGA Setup... - Page 70 Type "D:\VGA\NT40\" in Winnt\VGA\" in the blank. the blank. c. Press the "OK" button. D:\5820\VGA.100\Winnt\VGA\ D:\VGA\NT40\ a. Select the highlighted item. b. Press the "OK" button. a. Press "Yes" to proceed. a. Press "OK" to reboot. PCM-5820 Series User's Manual...
-
Page 71: Further Information
Click "OK" to save the setting. E N D Further information For further information about the PCI/SVGA installation in your PCM-5820 Series, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: Cyrix web site: www.cyrix.com Chapter 5 SVGA Setup... - Page 72 PCM-5820 Series User's Manual...
-
Page 73: Chapter 6 Audio
Audio • Introduction • Installation of audio driver for Windows 95/98/NT... -
Page 74: Introduction
Before installing the audio driver, please take note of the proce- dures detailed below. You must know which operating system you are using in your PCM-5820 Series, and then refer to the corre- sponding installation flow chart. Just follow the steps in the flow chart. -
Page 75: Installation For Windows 95/98
6.2.1 Installation for Windows 95/98 a. Select "Start", "Settings", "Control Panel", "System", "Device Manager". b. Click the "Other Devices" item. c. Remove items related to ESS 1869. CX 5530. a. Select "Add new hardware". b. Click "Next". a. Choose "No", click "Next". - Page 76 Click "Have Disk". a. Insert the disc into the CD-ROM drive. b. Type the correct path "D:\5820\VGA.100\ Win9X\Audio" and D:\5820\VGA.100\Win9X\Audio\ click the "OK" button. a. Select "ES1869 Control interface". a. Click "Finish" to complete. PCM-5820 Series User's Manual...
- Page 77 a. Click "OK". a. Insert Windows 95 b. Type the path of your Windows 95 disc and click "OK". D:\5820\VGA.100\Win9X\Audio a. Click "Yes" to restart. E N D Chapter 6 Audio...
-
Page 78: Installation For Windows Nt
Double click "Multimedia". a. Select the "Devices" item. b. Click "Add". a. Select the "Unlisted..." item. b. Click "OK". a. Insert the disc into the CD-ROM drive. b. Type "D:\5820\VGA.100\ D:\5820\VGA.100\Winnt\Audio Winnt\Audio" and click "OK". PCM-5820 Series User's Manual... - Page 79 a. Choose the highlighted item. b. Click the "OK" button. a. Set the I/O address. b. Click "Continue". a. Set ESS 1869 configuration. b. Click "OK" to restart. E N D Chapter 6 Audio...
- Page 80 PCM-5820 Series User's Manual...
-
Page 81: Chapter 7 Pci Bus Ethernet Interface
PCI Bus Ethernet Interface This chapter provides information on Ethernet configuration. • Introduction • Installation of Ethernet driver for Windows 95/98/NT • Further information... -
Page 82: Introduction
Introduction The PCM-5820 Series is equipped with a high performance 32-bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems. It is also both 100Base-T and 10Base-T compatible. The medium type can be configured via the RSET8139.exe program included on the utility disk. -
Page 83: Installation For Windows 95/98
7.2.2 Installation for Windows 95/98 a. Select "Start", "Settings", "Control Panel". b. Double click "Network". a. Click "Add" and prepare to install network functions. a. Select the "Adapter" item to add the Ethernet card. a. Click "Have Disk" to install the driver. Chapter 7 PCI Bus Ethernet Interface... - Page 84 Choose the "Realtek" item. b. Click "OK". a. Make sure the configurations of relative items are set correctly. b. Click "OK" to reboot. E N D Note: The correct path for Windows 98 is: "D:\5820\Ethernet.100\Win98" PCM-5820 Series User's Manual...
-
Page 85: Installation For Windows Nt
7.2.3 Installation for Windows NT a. Select "Start", "Settings", "Control Panel". b. Double click "Network". a. Choose the "Adapters" label. b. Click the "Add" button. a. Press "Have Disk". a. Type "A:". b. Press "OK". Chapter 7 PCI Bus Ethernet Interface... - Page 86 Fill in the correct path. D:\5820\Ethernet.100\Winnt\ A:\Winnt\ c. Click "OK". a. Choose the "Realtek" item. b. Click "OK". a. Make sure the configurations of relative items are set correctly. b. Click "OK" to reboot. E N D PCM-5820 Series User's Manual...
-
Page 87: Further Information
Further information Realtek website: www.realtek.com Chapter 7 PCI Bus Ethernet Interface... - Page 88 PCM-5820 Series User's Manual...
-
Page 89: Appendix A Pin Assignments
Pin Assignments This appendix contains information of a detailed or specialized nature. It includes: • CRT display connector • Flat panel display connector • COM2 RS-232/422/485 serial port connector • Keyboard and mouse connector • Main power connector • IDE hard drive connector •... -
Page 90: Crt Display Connector (Cn18)
DDCSCL Flat panel display connector (CN12) Table A-2: Flat panel display connector Function Function +12 V +12 V Vcc_LCD Vcc_LCD PD10 PD11 PD12 PD13 PD14 PD15 PD16 PD17 SHFCLK DE (M) ENABKL VSAFE (ENAVDD) 44 Vcc_LCD PCM-5820 Series User's Manual... -
Page 91: Com2 Rs-232/422/485 Serial Port (Cn14)
COM2 RS-232/422/485 serial port (CN14) Table A-3: COM2 RS-232/422/485 series port RS-232 port RS-422 port RS-485 port TxD+ DATA+ TxD- DATA- RxD+ RxD- Keyboard and mouse connnector (CN17) Table A-4: Keyboard and mouse connector Signal KB DATA MS DATA KB CLOCK MS CLOCK Appendix A Pin Assignments... -
Page 92: Main Power Connector (Cn9)
DATA 15 SIGNAL GND DRQ* IO WRITE* IO READ* IO CHANNEL READY 28 IRQ14 (IDE IRQ) IOCS16* ADDR 1 ADDR 0 ADDR 2 HARD DISK HARD DISK SELECT 0 SELECT 1 IDE ACTIVE* * low active PCM-5820 Series User's Manual... -
Page 93: Com1 Rs-232 Serial Port (Cn16)
COM1 RS-232 serial port (CN16) Table A-7: COM1 RS-232 serial port Signal Ethernet 100Base-T connector (CN13) Table A-8: Ethernet 100Base-T connector Signal XMT+ XMT- RCV+ RCV- Appendix A Pin Assignments... -
Page 94: Auxilary Power Connector (Cn10)
Table A-10: Floppy drive connector Signal Signal DENSITY SELECT* INDEX* MOTOR 0* DRIVE SELECT 1* DRIVE SELECT 0* MOTOR 1* DIRECTION* STEP* WRITE DATA* WRITE GATE* TRACK 0* WRITE PROTECT* READ DATA* HEAD SELECT* DISK CHANGE* * low active PCM-5820 Series User's Manual... -
Page 95: Parallel Port Connector (Cn3)
Parallel port connector (CN3) Table A-11: Parallel port connector Signal STROBE* AUTOFD* ERROR* INIT* SLCTINI* ACK* BUSY SLCT * low active Appendix A Pin Assignments... -
Page 96: Ir Connector (Cn7)
DATA 1+ Audio connector (CN5) Table A-14: Audio connector Signal Signal SPEAKER OUT R+ SPEAKER OUT R- SPEAKER OUT L+ SPEAKER OUT L- LINE OUT R LINE OUT L LINE IN R LINE IN L MIC IN PCM-5820 Series User's Manual... -
Page 97: Cd Audio Connector (Cn1)
CD audio connector (CN1) Table A-15: CD audio connector Signal CD audio control R CD audio control L LVDS connector (CN15) Table A-16: LVDS connector Signal Signal TX0- TX0+ TX1- TX1+ TX2- TX2+ TXCK- TXCK+ CPU fan power connector (CN6) Table A-17: CPU fan power connector Signal +5 V... -
Page 98: Rca (Composite) Connector (Cn21)
RCA (composite) connector (CN21) C om posite G N D S-Video connector (CN22) Table A-18: S-Video connector Signal Luminance output (brightness) Chrominance output (color) Table A-19: SCART Mode (optional) Signal Blue CSYNC Green PCM-5820 Series User's Manual... -
Page 99: Atx Power Feature Connector (Cn23)
ATX power feature connector (CN23) Table A-20: ATX power feature connector (CN23) Signal 5VSB (Stand-by voltage) VPSON ATX power button & power LED connector (CN24) Table A-21: ATX power button & power LED connector (CN24) Signal LED+ Button+ LED- (GND) Button- (GND) Appendix A Pin Assignments... - Page 100 PCM-5820 Series User's Manual...
-
Page 101: Appendix B System Assignments
System Assignments • System I/O ports • DMA channel assignments • Interrupt assignments • 1st MB memory map... -
Page 102: System I/O Ports
3D0-3DF Color/graphics monitor adapter 3F0-3F7 Diskette controller 3F8-3FF Serial port 1 Watchdog timer * PNP audio I/O map range from 220 ~ 250H (16 bytes) MPU-401 select from 300 ~ 330H (2 bytes) ** default setting PCM-5820 Series User's Manual... -
Page 103: Dma Channel Assignments
B.2 DMA channel assignments Table B-2: DMA channel assignments Channel Function Available Audio* Floppy disk (8-bit transfer) Parallel** Cascade for DMA controller 1 Audio* Available Available * Audio DMA default setting: DMA 1.5 Audio High DMA select: DMA 1.3 Audio Low DMA select: DMA 5.6.7 ** Parallel port DMA default setting: DMA 3 Parallel port DMA select: DMA 1.3 Appendix B System Assignments... -
Page 104: Interrupt Assignments
IRQ 4 Serial communication port 1 IRQ 5 Audio* IRQ 6 Diskette controller (FDC) IRQ 7 Parallel port 1 (print port) * Audio default setting: IRQ5 USB and Ethernet IRQ is automatically set by the system PCM-5820 Series User's Manual... -
Page 105: 1St Mb Memory Map
B.4 1st MB memory map Table B-4: 1st MB memory map Addr. range (Hex) Device F000h - FFFFh System ROM D800h - EFFFh Unused D000 - D400H available C800h - D7FFh Ethernet ROM* C000h - C7FFh VGA BIOS B800h - BFFFh CGA/EGA/VGA text B000h - B7FFh Reserved for graphic mode usage... - Page 106 PCM-5820 Series User's Manual...
-
Page 107: Appendix C Lcd Services
LCD Services This appendix contains information of a detailed or specialized nature. It includes information about 18-bit TFT LCD interfaces. -
Page 108: Lcd Services
A minimum of seven working days is required for completion of service, starting from receipt of the LCD package by For the 18-bit TFT display support list, please contact our custom- er service department for more detailed information and service files. PCM-5820 Series User's Manual... -
Page 109: Appendix D Installing Pc/104 Modules
Installing PC/104 Modules This appendix gives instructions for installing PC/104 modules. -
Page 110: Installing Pc/104 Modules
The PCM-5820 Series' PC/104 connectors give you the flexibility to attach PC/104 modules. Installing these modules on the PCM-5820 Series is quick and simple. The following steps show how to mount the PC/104 modules: 1. Remove the PCM-5820 Series from your system, paying particular attention to the safety instructions already mentioned above. -
Page 111: Figure D-1: Pc/104 Module Mounting Diagram
P C /1 0 4 M o u n tin g S u p p o rt F e m a le M a le P C /1 0 4 m o d u le P C M -5 8 20 S e rie s Figure D-1: PC/104 module mounting diagram 8 .9 8 2.5... -
Page 112: Table D-1: Pc/104 Connectors (Cn8)
IRQ7 — — IRQ6 — — IRQ5 — — IRQ4 — — IRQ3 — — DACK2* — — — — BALE — — +5 V — — — — — — — — * active low PCM-5820 Series User's Manual... -
Page 113: Appendix E Programming The Watchdog Timer
Programming the Watchdog Timer The PCM-5820 Series is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for whatever reason. This feature ensures system reliability in industrial standalone or unmanned... -
Page 114: Programming The Watchdog Timer
You must write your program so that it writes 1 to I/O port 443 at an interval shorter than the timer's preset interval. The timer's intervals have a tolerance of ± 30%, so you should program an instruction that will refresh the timer about every second. PCM-5820 Series User's Manual... - Page 115 The following program shows how you might program the watchdog timer in BASIC: Watchdog timer example program X=Out &H443, 1 REM Enable and refresh the watchdog GOSUB 1000 REM Task #1, takes 1 second to complete X=Out &H443, 1 REM Refresh the watchdog GOSUB 2000 REM Task #2, takes 1 second to...
- Page 116 PCM-5820 Series User's Manual...
-
Page 117: Appendix F Mechanical Drawings
Mechanical Drawings... -
Page 118: Figure F-1: Board Dimensions Pcm-5820/L/E
Component side Figure F-1: Board Dimensions component side (PCM-5820, PCM-5820L, PCM-5820E only) PCM-5820 Series User's Manual... -
Page 119: Figure F-2: Board Dimensions Component Side (Pcm-5822)
Component side (PCM-5822) Figure F-1: Board Dimensions component side (PCM-5822 only) Appendix F Mechanical Drawings... -
Page 120: Figure F-3: Board Dimensions Solder Side (Pcm-5820 Series)
Solder side Figure F-3: Board Dimensions solder side (PCM-5820 Series) PCM-5820 Series User's Manual...