Panel Facilities And Specifications - Pioneer S-W100S Service Manual

8. PANEL FACILITIES AND SPECIFICATIONS

7 PANEL FACILITIES
3
2
POWERED SUBWOOFER
1
FRONT PANEL
1 Power switch (POWER)
When pressed, power is turned ON; when pressed again, power is
turned OFF.
2 Power Indicator
Illuminates when the power is on.
3 Phase switch (PHASE — 0˚ / _ 180˚)
When depressed (_ 180˚), the output phase becomes the reverse
of the input signal, and when raised (— 0˚ ), it is in the same phase
as the input signal.
÷ Normally, the switch is set to (— 0˚ ).
But when the sound connection between the subwoofer and
the left and right speakers sounds unnatural, try switching to
180˚ and set the switch in the position where the sound is natural.
4 Level knob (LEVEL)
Sets the subwoofer volume.
÷ Turn the knob slowly from the MIN position.
÷ With this unit, the bass level can be independently set, so do
not turn up the bass on the stereo amplifier.
5 Turnover knob (TURNOVER)
Sets the high limit of the frequency played back by the subwoofer.
÷ Setting Criteria
50Hz ... when the diameter of the left/right speakers is 20-cm (8 in.)
or more.
100Hz . when the diameter of the left/right speakers is 10 – 25-cm (4
– 10 in.).
200Hz . when the diameter of the left/right speakers is 12-cm (5 in.)
or less.
7 SPECIFICATIONS
Cabinet ...................... Floor type with passive radiator system
Speaker (Magnetically shielded type) ........... 16 cm cone type
Passive radiator .................................. 15.6 cm x 28.6 cm oval
Power Amplifier
Continous Power Output (RMS) ...... 100 W/4 Ω (30 – 200 Hz)
Total Harmonic Distortion ................................................ 0.5 %
÷
Above specifications are for when power supply is 230 V.
Input (sensitivity at 100 Hz/impedance) (MYXMA, MLXMA/E)
SPEAKER LEVEL .................................... 1.6 V + 1.6 V/15 kΩ
4 5
∫¿ˆ¥YY∫
(30 – 200 Hz, 4 Ω, 25 W)
(both channels in-phase)
67
R L
R L
REAR PANEL
6 Line Level Input terminal (LINE LEVEL INPUT)
Connects to the stereo amplifier's SUBWOOFER PRE-OUT
terminal, with the specially provided RCA plug cord.
7 Line Level Output terminal (LINE LEVEL OUTPUT)
Used for connecting other equipment through the amplifier.
8 Speaker Level Output terminals
(SPEAKER LEVEL OUTPUT)
When the speakers output terminals on the stereo amplifier
are connected to this unit's SPEAKER LEVEL INPUT terminals
9 and used as the unit's input signal, these terminals are used
to connect the left and right speakers via the unit.
9 Speaker Level Input terminals
(SPEAKER LEVEL INPUT)
Connect to the speakers output terminals on the stereo
amplifier, with the specially provided speaker cords.
LINE LEVEL (RCA jack) ...................................... 160 mV/50 kΩ
Turnover Frequency .......... 50 – 200 Hz (continuously variable)
Outline Dimension ................. 190 (W) x 430 (H) x 430 (D) mm
Weight (without package) ............................................ 10.0 kg
Power Requirements
European model .............................. AC 220 – 230 V, 50/60 Hz
Singapore model .............................. AC 220 – 230 V, 50/60 Hz
Multi-voltage model .............. AC 110 – 115V/120V – 127V/220 – 230V
Power Consumption
Singapore model ............................................................... 82 W
European models .............................................................. 86 W
Multi-voltage model ......................................................... 243 W
Accessories ............................................. Speaker cords x 2
Warranty card (MYXMA: Only) x 1
NOTE:
Specifications and design subject to possible modification
without notice, due to improvements.
S-W100S
8
9
/240V (seleccionable), 50/60 Hz
RCA plug cord x 1
Operating instructions x 1
13