Kenwood KDC-MP632U Service Manual page 12

KDC-MP632U
KDC-W6534U/UY/X590/X7533U
QQ
3 7 63 1515 0
• With the remote controller, continuous forwarding is pro-
hibited.
• Using the VOL knob, [
adjusted in 3 steps : R15 ↔ 0 ↔ F15 (The initial value is 0)
• Using the VOL knob, [
be adjusted in 3 steps : L15 ↔ 0 ↔ R15 (The initial value is
0)
• Using the VOL knob, [
/ Treble Level can be adjusted in 3 steps : –8 ↔ 0 ↔ +8
(The initial value is 0)
• Using the VOL knob, [
Rear can be adjusted in 2 steps : Through ↔ 180Hz (or
220Hz) (The initial value is Through)
• Using the VOL knob, [
can be adjusted in 2 steps : 60Hz (or 50Hz) ↔ Through
(The initial value is Through)
• Using the VOL knob, [
Phase can be adjusted in 2 steps : Reverse ↔ Normal
(The initial value is Normal)
• Using the VOL knob, [
can be adjusted in 2 steps : –8 ↔ 0 (The initial value is 0)
• Using the VOL knob, [
TE
L 13942296513
OFF can be adjusted in 2 steps : OFF ↔ ON (The initial
value is OFF)
• Using the VOL knob, [
can be adjusted in 2 steps : OFF ↔ ON (The initial value is
OFF)
• Bass f / Bass Q / Bass EXT / Middle f / Middle Q / Treble f
do no appear in audio adjustments.
MENU
• Press the [Q] key to enter the MENU.
• Press the remote control [DNPP/SBF] key or the [DIRECT]
key to enter the MENU.
• Continuous forwarding by remote control is prohibited.
• Initial item in CD/USB source is "F/W Version".
2-ZONE (Dual Zone) items (Model with 2-ZONE
only)
• When using sources other than the STANDBY source, press
[AUTO] or [TI] key for less than 1 second, 2-ZONE ON/
OFF is achieved.
www
Backup current measurement
When reset in ACC OFF (Back Up ON) condition, MUTE ter-
minal goes off after 2 seconds, instead of 15 seconds. (During
.
this time, the CD mechanism does not function.)
12
TEST MODE
] and [ ] key, the Fader can be
] and [ ] key, the Balance can
] and [ ] key, the Bass / Middle
] and [ ] key, the HPF Front /
] and [ ] key, the LPF Sub Woofer
] and [ ] key, the Sub Woofer
] and [ ] key, the Volume Offset
] and [ ] key, the Loudness ON/
] and [ ] key, 2-Zone ON/OFF
x ao
y
i
8
OPEL communication items (Model with OPEL
communication)
During the test mode, OPEL communication line outputs the
following (At every 500msec, the output condition of the com-
munication line will be switched.)
CE
DATA
CLK
500msec
500msec
Special displays while all lights are on
When all lights are on with STANDBY source, if the follow-
ing keys are pressed, the following messages are displayed.
[1] key Version is displayed (forwarding)
(Display) TYPE : x_ _ _ ("x" is displayed in hexadecimals)
→ 512K – 1.02 ("development ID" – "version")
Q Q
3 6 7 1 3
→ all lights on →
∗ TYPE indicates µ-com destination, and shows real-time
condition of the destination terminal.
[2] key Serial No. is displayed (8 digits)
(Display) xxxxxxxx
[3] key Key pressed: Power ON time is displayed.
While Power ON time is displayed, press and hold for 2
seconds or longer to clear the Power ON time.
(Display)
PON_0Hxx (00~50 is displayed for "xx". When less
xxxxx (00001~10922 is displayed for "xxxxx")
[4] key Key pressed: CD operation time is displayed.
Press the key for more than 2 seconds while the CD
operation time is displayed to clear CD operation time.
(Display)
CDT_0Hxx (00~50 is displayed for "xx". When less
u163
.
xxxxx (00001~10922 is displayed for "xxxxx")
2 9 9 4 2 8
500msec
1 5 0 5 8 2 9 9 4
than 1 hour, display by increment of 10
minutes.)
MAX 10922 (hours)
m
co
than 1 hour, display by increment of 10
minutes.)
MAX 10922 (hours)
9 9
2 8 9 9