Table of Contents
Related Manuals for AerodromeRC aviatik 30.40
Summary of Contents for AerodromeRC aviatik 30.40
- Page 1 AVIATIK 30.40 36” 1/8 S���� R/C S���� M���� I����������� Designed by M.K. Bengtson Prototype by Bert Ayers Manual by Bert Ayers M����������� ��� D���������� ��: Bengtson Company e-mail: sales@aerodromerc.com www.aerodromerc.com...
-
Page 2: Model Specifications
Removing them all at once is asking for lost and broken parts. Especially parts Thank you for buying the AerodromeRC Aviatik 30.40 36” like S9 or A4, A11 that are so small they can easily slip laser cut short kit for electric flight. -
Page 3: Tail Surfaces
• 35” 1/8”x 1/4” bass wood spar (2 – 24” pieces) pl?num=1249592840. • 35” 1/8”x 3/8” bass wood spar (2 – 24” pieces) The Aviatik 30.40 36” prototype was built by Bert Ayers. • 35” 1/4” square balsa strip (2 pieces cut from 1/4” balsa sheet [scrap]) TAIL SURFACES •... - Page 4 A������ 30.40 36” 1/8�� ����� Page 4 www.AerodromeRC.com pu�ing in each rib on the le� then right. Ribs R2a, R2b and R3 can be preassembled. Careful to get R2b and R3 in correct location. This builder glued them as he came to them.
-
Page 5: Fuselage Construction
A������ 30.40 36” 1/8�� ����� Page 5 www.AerodromeRC.com • 3 – 4-40 blind nuts • 1 Neo Magnet F������ S������ The fuselage is built in two sections. If build in one section (front and rear together) the a� section will be curved. It will not match the top view and will not be scale. - Page 6 A������ 30.40 36” 1/8�� ����� Page 6 www.AerodromeRC.com On the top plan view, pin down part TS2 (not TS5). Bevel the inside of the tail post so that they can be brought Epoxy F1 to the front of the right side section, being very together about an 1/8”.
- Page 7 A������ 30.40 36” 1/8�� ����� Page 7 www.AerodromeRC.com Slide the rear section into position, centering it on the plan center line. The piece that was tacked to the tail post should elevate the rear to fit properly with the front section, adjust where needed.
- Page 8 A������ 30.40 36” 1/8�� ����� Page 8 www.AerodromeRC.com This builder likes to make a fixture, copied from the plans, to sand the proper radiuson the cowl balsa. This builder also added two 1/8” wood dowel pins to the rear side of C1 that went into the F1d former at the datum line point on each side.
-
Page 9: Motor Mount
A������ 30.40 36” 1/8�� ����� Page 9 www.AerodromeRC.com MOTOR MOUNT Use two lengths of heavy thread or string. Tack glue one end of thread parallel with top of the cylinder. Wind both Items needed but not furnished in the short kit: threads down around the cylinder. -
Page 10: Landing Gear
A������ 30.40 36” 1/8�� ����� Page 10 www.AerodromeRC.com LANDING GEAR Return to the landing gear bending diagram. Measure the width of the wire where it mounts to the plywood Items needed but not furnished in the Short Kit: mounting plates. Measure the width where these wires •... -
Page 11: Contact Information
fit, then run some thin CA glue CONTACT INFORMATION around the plywood rim to secure the tire. The Aviatik 30.40 36” was designed by M.K. Bengtson Copy the Wire Wheel cone pa�ern onto the heavy card stock. Cut out the circle then lightly score the spoke e-mail: kay@aerodromerc.com...