Related Manuals for Samson trovis 5570
Summary of Contents for Samson trovis 5570
- Page 1 Automation System TROVIS 5500 Room Panel TROVIS 5570 Mounting and Operating Instructions EB 5570 EN Firmware version 1.0x ® Edition March 2003 Electronics from SAMSON...
- Page 2 Moreover, we do not guarantee that the buyer can use the product for an intended purpose. SAMSON rejects any liability for claims by the buyer, especially claims for compensation including lost profits or any other financial loss, except the damage was caused by wrongful intent or by gross negligence.
-
Page 3: Table Of Contents
Contents Contents Operation ....... 4 Operating elements......4 Displaying data . -
Page 4: Operation
Operation Operation The room panel, a remote room controller, will be ready for use after it has been connected and started up. If the phone icon located in the top left-hand corner flashes, repeat the start-up procedure (–> p. 10). Operating elements Arrow keys (up and down keys) Are used to select data and parameters. -
Page 5: Displaying Data
Operation Displaying data The data are displayed in turn on each press of the key. Use the key to display the data in reverse order. The arrow (data indicator) at the top of the display indicates the data selected, by pointing to the corresponding icon printed on the housing of the room panel. It is recommended that the desired data be selected with the cover closed to ensure that the data displayed are assigned to the appropriate icons. -
Page 6: Selecting The Operating Mode
Operation Important! If the phone icon flashes in the top left-hand corner, the connection to the heating and district heating controller is faulty. Selecting the operating mode Press the key repeatedly to cycle through the following operating modes: ; 55555… Rated operation (day): The day set point (rated operation) will be continuously maintained regardless of the programmed times of use. -
Page 7: Setting The Data
Operation Setting the data The room panel allows for direct setting of the clock, times of use, day set point, night set point and party mode in the parameter level. Note! If the user fails to press a key for two minutes, the room panel will leave the parameter level. 1.4.1 Setting the clock Proceed as follows: Open the cover. -
Page 8: Setting The Times Of Use
Operation 1.4.2 Setting the times of use Three times of use can be programmed for each day of the week. If one time of use is not required, be sure that the start and stop times are adjusted to identical values. Proceed as follows: Open the cover. -
Page 9: Setting The Temperature Set Points
Operation 1.4.3 Setting the temperature set points The day set point specifies the room temperature to be maintained during rated operation. The night set point specifies the room temperature to be maintained during reduced opera- tion. When adjusting the set points in the parameter level, the following applies: Parameter Arrow points to Display... -
Page 10: Start-Up
Start-up Start-up The TROVIS 5570 Room Panel is intended to be used in combination with a heating and dis- trict heating controller from the TROVIS 5500 Series. The start-up of the room panel requires the heating and district heating controller to be con- figured as specified below. -
Page 11: Calibrating The Room Sensor
Installation Calibrating the room sensor If the temperature displayed by the room panel does not correspond with the actual room temperature, the value measured by the room sensor can be changed and readjusted. When calibrating the room sensor, change the currently displayed sensor value to the reference value, i.e. -
Page 12: Electrical Connection
Electrical connection Electrical connection Prior to connecting the room panel to the heating and district heating controller, route two wires (or four wires including two wires for the power supply) in the building. When connecting the devices, there is no particular polarity requirement. Connecting to the TROVIS 5575 Heating and District Heating Controller: Connect terminals 5 and 6 of the room panel to terminals 14 and 15 of the controller device bus. - Page 13 EB 5570 EN...
- Page 16 SAMSON AG ⋅ MESS- UND REGELTECHNIK Weismüllerstraße 3 ⋅ 60314 Frankfurt am Main ⋅ Germany Phone: +49 69 4009-0 ⋅ Fax: +49 69 4009-1507 EB 5570 EN Internet: http://www.samson.de...