Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TREND t30
Summary of Contents for TREND t30
- Page 2 SAFETY Keep work area clean. Cluttered oil and sharp edges. Always trail workshops and benches can the power cord away from the cause injuries work area. Observe the safety regulations in the instruction manual of the Power Use the attachment with the Connect dust extraction Tool to be used or connected to this power tools and accessories...
- Page 3 Recommended speeds can be found on the packaging, in cutter After work, release the router instructions or in the Trend plunge to protect the cutter. Routing Catalogue. Always use a push-stick or push- Always use router cutters in a block for last 300mm of the cut.
-
Page 4: Electrical Safety
Also refer to the table below. are competent to do this, proceed as instructed below. If you are in doubt, contact an authorised Cable Rating (Amperes) Trend Repair Agent or a qualified electrician. Voltage 110V 230V Disconnect the plug from the supply. -
Page 5: Vacuum Cleaning Safety
VACUUM CLEANING SAFETY General Safety General Safety Regulations when Routing Noise Fire and explosion hazard. The level of noise when routing may exceed 85 Never vacuum-clean inflammable fluids, such dB(A). It is therefore advisable to wear ear as gas, oil, alcohol, solvents, etc. Do not defenders especially if routing for long periods of work near inflammable fluids or gas. -
Page 6: Manufacturer's Declaration
Stephen Phillips Also for the T30AF & T30ALF 1 x Nylon Pre-Filter Trend Machinery & Cutting Tools Ltd. For extraction of fine dust particles the 0.3 micron cartridge filter must be used with the nylon pre-filter and paper filter bag. -
Page 7: Description Of Parts
Carrying handle Motor filter Float Cartridge filter -for T30A & T30/EURO (12 micron) -for T30AF & T30ALF (0.3 micron) Paper-filter bag Container Cartridge filter cap Container catch Bumper... - Page 8 ASSEMBLY Some of the accessories are supplied inside the container and so must be removed before using the unit. Insert the five castor wheels in their purposely provided housings under the container (9). Connect the hose to container (9). To remove it, push button (14) and pull the hose towards you.
-
Page 9: Operation
OPERATION Suction of Dry Dust and Dirt The filter cartridge (7) has to be completely pushed in and is secured by turning the filter cartridge cap (10). Check that it fits correctly. In order to remove the cartridge filter (7) turn the cap (10) anti-clockwise and draw the cartridge filter. -
Page 10: Suction Of Fluids
TURNED For the location of your nearest Trend Service OFF to avoid its accidental starting. Agent, please call the telephone number at the Remember the power tool socket is back of this manual. - Page 11 T30 - SPARE PARTS LIST v3.0 07/2003 Qty. Desc. Ref. Container Housing WP-T30/001 Motor Cover WP-T30/002 Motor Housing WP-T30/003 Container Clip WP-T30/004 Castor WP-T30/005 3 Core Cable with Plug 230V UK WP-T30/006 2 Core Cable with Plug 230V EURO WP-T30EUR/006...
- Page 12 T30 - SPARE PARTS LIST v3.0 07/2003 Item Description Ref. Lower Motor Housing WP-T30/034 Foam Baffle Lower Housing WP-T30/035 Rubber Grummet External WP-T30/036 Float WP-T30/037 Float Cage WP-T30/038 Cartridge Filter 12 Micron (T30A) T30/6 Cartridge Filter 0.3 Micron (T30AF & T30ALF)
- Page 13 T30 - SPARE PARTS DIAGRAM v3.0 07/2003 yy yy yy yy yy yy -IB-...
- Page 14 Web: ___________www.trendmachinery.co.uk RECYCLABLE © Copyright Trend 2003. No part of this publication may be reproduced, stored or transmitted in any form without prior permission. Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools...
Need help?
Do you have a question about the t30 and is the answer not in the manual?
Questions and answers